Panduit CT-460 Bedienungsanleitung

CT-460: PA24481A01_04 Page: 1 of 4 6-2018

CT-460

PA24481A01

Rev. 046-2018

NEW TOOLS – BEFORE PLACING INTO SERVICE

1. VISUALLY INSPECT TOOL

FOR DAMAGE.

All Panduit crimping tools are calibrated and inspected before they are shipped from

the factory. There is, however, a possibility of damage in shipment. All new tools

should therefore be inspected before being used.

2. CHECK DIE CLOSURE

3. CLEAN EXCESS OIL FROM

CRIMP DIES AND USE.

New tools are shipped factory lubricated. They do not require extensive cleaning.

After inspection, simply clean any excess oil from the crimping dies and place into

service.

CAUTION: Verify power is “OFF” before

working on wiring with this tool. The plastic grips

are for the user’s comfort—and are not intended

to insulate against shock while working on live

electrical circuits.

WARNING: Controlled cycle device prevents tool from opening before cycle is

completed. Keep hands and other objects clear of pinch areas before closing.

ATTENTION: TO DISENGAGE CONTROLLED CYCLE DEVICE:

Turn the ratchet release screw counterclockwise and open handles.

The controlled cycle device will automatically reset after screw is released.

Email:

techsupport@panduit.com

EU Website:

www.panduit.com/emea

EU Email:

Emeatoolservicecenter

@panduit.com

www.panduit.com

Technical Support:

1-800-777-3300

Panduit Europe • EMEA Headquarters

Tel: +31 (0) 546 580 452 • Fax: +31 (0) 546 580 441

CRIMP DIES for

Pan-Term

insulated

terminals, splices

and wire joints.

Lock Screw

Notch

Ratchet Release

Screw

Locator Retention

Screw

BACK

VIEW

(FIG. 1)

FRONT

VIEW

(FIG. 2)

Adjustment

Terminal Locator

CT-460: PA24481A01_04 Page: 2 of 4 6-2018

INSULATED TERMINAL INSTRUCTIONS

1. With handles in open position, insert terminal in

proper size die so that tongue slides into locator

slot. See product packaging for proper crimping

pockets.

2. Position terminal against locator and close handles

until barrel is held snugly in place -- do not deform

barrel.

Insert stripped wire into terminal until conductor

extends beyond barrel. See product packaging for

wire strip length.

Crimp by closing handles until controlled cycle

device releases. Handles will open automatically,

and crimped terminal may be removed.

FIG. 3

INSULATED SPLICE INSTRUCTIONS

1. Remove locator using a 2.5mm Allen wrench on the

locator retention screws [see FIG. 1]. (The 2.5mm

wrench may be used simultaneously to secure

screws on opposite side.)

With locator removed and handles opened, insert

splice in proper size die so that barrel extends

1/16" beyond insulation closures.

3. Close handles until barrel is held snugly in position

-- do not deform barrel.

4. Insert stripped wire into splice and crimp by closing

handles until controlled cycle device releases.

Remove splice and repeat operation for crimping

other half of barrel.

FIG. 4

INSULATED WIRE JOINT INSTRUCTIONS

1. Remove locator using a 2.5mm Allen wrench on the

locator retention screws [see FIG. 1]. (The 2.5mm

wrench may be used simultaneously to secure

screws on opposite side.)

With terminal locator removed, insert wire joint in

proper size die so that ribs of molded insulator are

positioned against face of tool.

3. Twist ends of stripped wire together, trim and insert

into wire joint.

4. Crimp by closing handles until controlled cycle

device releases. Handles will open automatically,

and crimped joint may be removed.

FIG. 5

CT-460: PA24481A01_04 Page: 3 of 4 6-2018

IN-SERVICE TOOLS – AFTER TOOLS HAVE BEEN IN SERVICE

1. CLEAN AND VISUALLY

INSPECT FOR DAMAGE

ONCE A MONTH.

In-service tools should be cleaned and inspected at least ONCE A MONTH. To

clean---immerse in a commercial degreasing compound and wipe clean with a

lint free cloth. If a degreasing compound is not available, wipe with a clean cloth.

2. CHECK DIE CLOSURE

After cleaning, inspect the crimping dies for proper die closure. See FIG. 6

for plug gaging instructions.

3. LUBRICATE TOOL ONCE

A WEEK.

4. CLEAN EXCESS OIL

FROM CRIMP DIES AND

USE.

In-service tools should be lubricated ONCE A WEEK, and after every cleaning.

Lubricate all pins, pivots and bearing surfaces with a good grade S.A.E. 20 or

equivalent motor oil. Be sure to clean any excess oil from crimping dies before

using.

VISUAL INSPECTION

1. Visually inspect tool for missing or loose pins; then close the tool and note the return action of the handles.

2. Remove the terminal locator and visually inspect the crimping dies for worn, chipped or broken surfaces.

Damaged crimping dies are objectionable and may go undetected when gaging the die closure.

3. If parts are missing, defective or damaged; contact your local Panduit Sales Office for information on repair or

replacement of tools; or contact Technical Support at 1-800-777-3300.

DIE CLOSURE INSPECTION: CT-460

Die Closure inspection is made by using the GO/NO-GO gaging dimensions listed in FIG. 6.

TO PERFORM DIE CLOSURE INSPECTION

1. Clean die and plug gage surfaces.

2. Close tool handles until crimping jaws are bottomed and handles are fully closed.

3. Using the proper gage member, insert the GO side into the die – it must pass completely through the

closure.

4. Reverse the gage and try to insert the NO-GO side into the die closure (Do Not use excessive force). The

NO-GO side may partially enter the die closure but must not pass completely through.

5. Perform the above procedure for both the crimp die closure and the insulation die closure, as listed in FIG. 6

CT-460: PA24481A01_04 Page: 4 of 4 6-2018

6. If both the GO and NO-GO conditions are met; the tool is dimensionally correct – if either condition fails,

adjust the DIE CLOSURE as follows:

a. Remove lock screw with small wrench [see FIG. 2].

b. With adjustment wrench provided, turn adjustment pin one notch – each notch produces

approximately .002” of adjustment. A clockwise turn increases the die closure and a counter-

clockwise turn decreases the die closure.

c. Close the tool and plug gage the die closure as instructed above. If the GO/NO-GO conditions are

not met, repeat Step (2) in one-notch increments until the tool is gages to be dimensionally correct.

Replace and tighten both lock screws after final adjustment.

7. If the above procedure fails to satisfy all GO and NO-GO conditions, contact your local Panduit Sales

Office; or contact Technical Support at 1-800-777-3300.

FIG. 6

POCKET

SIZE

CRIMP DIE CLOSURE

GAGING GAGE ELEMENT

DIAMETERS

GO NO-GO GO NO-GO

16-14 BLUE 0.114 0.124 0.1140 - 0.1143 0.1237 - 0.1240

12-10 YELLOW 0.153 0.163 0.1530 - 0.1533 0.1627 - 0.1630

POCKET

SIZE

INSULATION DIE CLOSURE

GAGING GAGE ELEMENT

DIAMETERS

GO NO-GO GO NO-GO

16-14 BLUE 0.142 0.158 0.1420 - 0.1423 0.1577 - 0.1580

12-10 YELLOW 0.195 0.211 0.195 - 0.1953 0.2107 - 0.2110

Andere Panduit Crimpwerkzeuge Handbücher

Panduit

Panduit CT-920 Series Bedienungsanleitung

Panduit

Panduit CT-460 Montageanleitung

Panduit

Panduit CT-1123 Bedienungsanleitung

Panduit

Panduit MSPT-1.3 Bedienungsanleitung

Panduit

Panduit CT-2940/L Bedienungsanleitung

Panduit

Panduit Black Fin CT-2931/STCVUK Bedienungsanleitung

Panduit

Panduit BlackFin CT-2920 Bedienungsanleitung

Panduit

Panduit BlackFin CT-2931/STBT Bedienungsanleitung

Panduit

Panduit CT-1104 Bedienungsanleitung

Panduit

Panduit Black Fin CT-2931 Series Bedienungsanleitung

Panduit

Panduit BlackFin CT-2600/L Bedienungsanleitung

Panduit

Panduit CT-1003 Bedienungsanleitung

Panduit

Panduit CT-1123 Bedienungsanleitung

Panduit

Panduit PAT4.0 Series Bedienungsanleitung

Panduit

Panduit BlackFin CT-2980/ST Bedienungsanleitung

Panduit

Panduit BlackFin CT-3980/BT Bedienungsanleitung

Panduit

Panduit CT-1000 Bedienungsanleitung

Panduit

Panduit PBTMT Bedienungsanleitung

Panduit

Panduit CTFP-100 Bedienungsanleitung

Panduit

Panduit Contour Crimp CT-1015 Bedienungsanleitung

Panduit

Panduit BlackFin CT-2600 Series Bedienungsanleitung

Panduit

Panduit BlackFin CT-2600/LBT Bedienungsanleitung

Panduit

Panduit CT-1000 Administratorhandbuch

Panduit

Panduit BlackFin CT-2300/ST Bedienungsanleitung

Beliebte Crimpwerkzeuge Handbücher anderer Marken

JST

JST CS 10 Bedienungsanleitung

molex

molex 63811-5100 Bedienungsanleitung

Danfoss

Danfoss ET4200 Bedienungsanleitung

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Bedienungsanleitung

TE Connectivity

TE Connectivity 2063528-1 Bedienungsanleitung

molex

molex 63825-3000 Bedienungsanleitung

Tyco Electronics

Tyco Electronics 69156-1 Bedienungsanleitung

CRH

CRH CRL CBLHCT1 Bedienungsanleitung

Emerson

Emerson Klauke ES 105CFM Bedienungsanleitung

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Bedienungsanleitung

Danfoss

Danfoss ET4350 Bedienungsanleitung

Milwaukee

Milwaukee M18 Bedienungsanleitung

HOGERT

HOGERT HT1P169 Bedienungsanleitung

Textron

Textron ESG105L Bedienungsanleitung

Tyco Electronics

Tyco Electronics 90035-3 Bedienungsanleitung

Emerson

Emerson Klauke ES 20RMCCFB Bedienungsanleitung

Continental Refrigerator

Continental Refrigerator PC150HD Bedienungsanleitung

TE Connectivity

TE Connectivity ERGOCRIMP 1-1579001-3 Bedienungsanleitung