Panduit Ezair CA9 Bedienungsanleitung

sources.

14- Remove protective coating from dies. Insert Crimp Die into the ram

of the Parts Guide. 12- Place Reel Holders onto Arm, apply pressure (compress spring) while tightening. then the Cutter Die. 15-Slide the cutter die upwards then tighten securely

with allen wrench (use small end of wrench to tighten)

Equipment Needed: Tools Needed: Safety Equipment

CP-871 Metric Allen wrenches (Set)

CA9 Applicator Dial Calipers

Power Cord and air line Side cutters Glasses

Terminals

Operation Manual

Tool Solutions Division - Romeoville, IL (USA)

Tighten screws to secure Arm. 2- Screw the Support Posts (2) into the side of the press.

Quick Start Guide

Part Number >> CP-871 Press / CA9 Applicator >> Setup, Loading and Operation

4- Attach Power Cord, Foot Pedal and Tool Feed (back of press)

5- Insert Air Hose into Air Regulator on Press then connect to air

1- Loosen screws (2) on Reel Arm and raise the arm high enough to accommodate reel; rotate 90°.

3-Place the Parts Guide over the Support Posts (2) slide to fasten, tighten knobs to secure.

interlock and applicator hits stop (B). 8-Raise the handle on the side of the press to secure applicator.

13- Check label for proper die set, initial setting and shut height. Turn dial to adjust to initial setting.

11-Place reel on Arm w/label facing outwards, tighten back Reel Stop until parts are aligned with the end

6- Use handle to Raise Safety Guard door until engaged (click sound). Make sure handle is in the

10- Loosen thumb screw and remove Reel Holders and spring.

9- Attach air line to inner fitting on press and adapter to applicator.

QS-CA9 Rev: 00 / April, 2012

Page: 1 of 2

down position. 7- Place the applicator on base of the press, raise ram (A), slide to the right until rams

Fully

Assembled

CP-871 with

CA9

Applicator

PRESS SET-UP

APPLICATOR INSTALLATION

clockwise until button releases and pops outward.

Equipment Needed: Tools Needed: Safety Equipment

CP-871 Metric Allen wrenches (Set)

CA9 Applicator Dial Calipers

Power Cord and air line Side cutters Glasses

Terminals

Operation Manual

16- Lift Feed Finger (A) and insert Lower Die (B).

19- Close Safety Guard. Power ON press by turning the Emergency Stop

17- Lower the Feed Finger into slot of lower die and tighten securely w/allen wrench.

20- Place solder slug into die area over lower die and press foot pedal.

18- Turn air onto the press. Air Regulator gage should read 0.6.

Tool Solutions Division - Romeoville, IL (USA)

Quick Start Guide

Part Number >> CP-871 Press / CA9 Applicator >> Setup, Loading and Operation

Page: 2 of 2

QS-CA9 Rev: 00 / April, 2012

22- Raise Safety Guard. Place the #1 Parts Pusher in rear position.

24- Unwind terminals from spool & feed them through parts guide & into the track.

past the finger and is on the right side of it.

28- Close Safety Guard door.

26- Place the #1 Part Pusher in the forward position.

29- Insert wire into the barrel of the terminal and press foot pedal.

27- Flip #2 Track Cover down (A), toggle ON/OFF (B) twice to advance parts into the die area.

30- Check that crimp is secure and continue with operation.

25. Slide terminals into track lift Feed Finger until the first part goes

21- Measure crimp indentation w/caliper to determine shut height. Refer to Oper. Manual for variances.

23- Lift track cover (A) and make sure toggle switch is in the OFF position (B).

OPERATION

Fully

Assembled

CP-871 with

CA9

Applicator

Dieses Handbuch passt für folgende Modelle

Andere Panduit Crimpwerkzeuge Handbücher

Panduit

Panduit CT-1123 Bedienungsanleitung

Panduit

Panduit BlackFin CT-2600 Series Bedienungsanleitung

Panduit

Panduit BlackFin CT-2931/STBT Bedienungsanleitung

Panduit

Panduit Black Fin CT-2931/STCVUK Bedienungsanleitung

Panduit

Panduit CT-1000 Bedienungsanleitung

Panduit

Panduit BlackFin CT-3980/BT Bedienungsanleitung

Panduit

Panduit CTFP-100 Bedienungsanleitung

Panduit

Panduit CT-2940/L Bedienungsanleitung

Panduit

Panduit BlackFin CT-2980/STBT Bedienungsanleitung

Panduit

Panduit CT-600-A Bedienungsanleitung

Panduit

Panduit CTFP-25 Bedienungsanleitung

Panduit

Panduit ClackFin CT-3001/CCPBT Bedienungsanleitung

Panduit

Panduit CT-930LPCH Bedienungsanleitung

Panduit

Panduit CT-1003 Bedienungsanleitung

Panduit

Panduit BlackFin CT-2980/ST Bedienungsanleitung

Panduit

Panduit Blackfin CT-2980/TO Bedienungsanleitung

Panduit

Panduit CT-2002CH Bedienungsanleitung

Panduit

Panduit CT-1000 Administratorhandbuch

Panduit

Panduit Contour Crimp CT-1015 Bedienungsanleitung

Panduit

Panduit CT-460 Montageanleitung

Panduit

Panduit CT-460 Bedienungsanleitung

Panduit

Panduit CT-3001 Bedienungsanleitung

Panduit

Panduit PBTMT Bedienungsanleitung

Panduit

Panduit BlackFin CT-2600/L Bedienungsanleitung

Beliebte Crimpwerkzeuge Handbücher anderer Marken

JST

JST CS 10 Bedienungsanleitung

molex

molex 63811-5100 Bedienungsanleitung

Danfoss

Danfoss ET4200 Bedienungsanleitung

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Bedienungsanleitung

TE Connectivity

TE Connectivity 2063528-1 Bedienungsanleitung

molex

molex 63825-3000 Bedienungsanleitung

Tyco Electronics

Tyco Electronics 69156-1 Bedienungsanleitung

CRH

CRH CRL CBLHCT1 Bedienungsanleitung

Emerson

Emerson Klauke ES 105CFM Bedienungsanleitung

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Bedienungsanleitung

Danfoss

Danfoss ET4350 Bedienungsanleitung

Milwaukee

Milwaukee M18 Bedienungsanleitung

HOGERT

HOGERT HT1P169 Bedienungsanleitung

Textron

Textron ESG105L Bedienungsanleitung

Tyco Electronics

Tyco Electronics 90035-3 Bedienungsanleitung

Emerson

Emerson Klauke ES 20RMCCFB Bedienungsanleitung

Continental Refrigerator

Continental Refrigerator PC150HD Bedienungsanleitung

TE Connectivity

TE Connectivity ERGOCRIMP 1-1579001-3 Bedienungsanleitung