pathway eGlass Bedienungsanleitung
!
For instructional videos, software downloads, or further training and support,
visit the eGlass Academy by scanning the QR Code with your phone"
or by visiting https://www.eglass.io/support
Quick Start Guide
When setting up eGlass, it’s best to follow the below steps in order. "
For example, you’ll need to see the camera image before “Calibrating Lighting”, which
is why “Installing Software” is a few steps ahead of “Calibrating Lighting”.
Unboxing
1
Assembly
2
Connecting
Installing Software
3
4
Computer Set-Up
5
Using Neon Pens
6
Setting Background
Calibrating Lighting
7
8
Eliminating Reflections
9
Using Software + Control Panel
10
The Setup Process
11
Turning-On
Support
!
Main eGlass Frame
4x Neon Glassboard Pens (Unactivated)
2x Support Legs
Cleaning Rag
Camera Arm
6x Support Leg Thumb Screws
USB Cable
2x Camera Arm Thumb Screws
Power Adapter
Anti-Reflection Hood
Power Cable
2x Anti-Reflection Hood Brackets
Polarizing Filter + Adapter
4x Anti-Reflection Hood Rods
1
2
3
4
5
6
7
8
9
15
17
18
19
20
10
16
1
2
3
4
5
6
7
8
9
15
10
17
16
What's In the Box?
18
19
20
Unboxing
1
2
3
4
5
6
7
8
9
10
11
!
Use optional polarizing filter to eliminate reflection of LCD computer screens.
Attach filter to camera arm using the filter adapter, and rotate filter until reflection is
minimized.
Page 2
1. Hand-tighten 6x M6 Thumb Screws to secure both Adjustable Support Legs
to the Main eGlass Frame. Ensure proper alignment so that both the AC power
port and USB port on the sides of the Main eGlass Frame are both accessible
with the Adjustable Support Legs installed.
2. Fasten the Camera Arm Assembly to the Main eGlass Frame with two M6
thumb screws. Hand tighten.
3. Install the lens filter by clipping it over the camera found on the Camera Arm
Assembly.
Assembly
Medium
(24”)
Low
(22”)
High
(26”)
High
(26”)
Low
(22”)
15
10
17
16
10
11
12
13
14
15
16
17
7
The support legs can be mounted in three height configurations. Install thumb screws in the color-coded
holes below depending on the desired height:
15
10
Choosing Height Setting
Assembly
2
1
3
4
5
6
7
8
9
10
11
!
Computer
Connect Computer
Use the included USB Cable to connect a PC, Mac, or Chromebook to the USB-In port on the bottom right
side of the eGlass frame.
Connect Power
A. Connect the Power Adapter to the Power Cable. "
B. Then plug one end of the Power Cable into a protected AC power outlet,"
C. and the other end of the Power Adapter into the DC-in port on the bottom left sider of the eGlass frame.
5
6
5
6
A.
C.
B.
5
6
4
Connecting
2
1
3
4
5
6
7
8
9
10
11
!
Need to see camera image before setting up "
•Before completing set-up process, please install the eGlassFusion Software onto your computer."
•Download Software from https://www.eglass.io/support "
•Chromebook users must use the HoverCam for Chrome App.
Download from
https://www.eglass.io/support
Computer Placement
•For optimal results, place computer screen on the other side of glass as close to eGlass camera as possible.
This will simulate eye contact when looking towards the computer screen. "
•Because computer will on the other side of glass and out of reach, use a mouse and keyboard (not included)
to operate."
•For best results, use a laptop stand (not included) as pictured below to position computer screen even closer
to the eGlass camera.
Laptop Stand
Good:
Best:
Computer Placement
2
1
3
5
4
6
7
8
9
10
11
Installing Software
2
1
3
4
5
6
7
8
9
10
11
eGlassFusion
!
Activate pen by dabbing tip into cloth upside-down until
ink flows to tip.
Store pens upside-down
when not in use to keep
tip saturated.
60sec
For a glowing effect, we recommend using neon dry erase markers, which can be purchased online.
Some recommended brands are:"
•Quartet Glass Whiteboard Dry Erase Markers - Neon"
•Arteza Glass Board Dry Erase Markers - Neon"
•Expo Neon Window Dry Erase Markers
To erase pen ink, simply use the included cloth to wipe the glass clean. Foaming glass cleaning solutions can
be used occasionally, but are not necessary for every day use.
The special properties of neon dry erase ink causes erased ink flakes to “clump” more
than standard dry erase markers, sometimes dirtying one's workspace. However, this
clumping is preferred as it causes ink particles to fall rather than remaining in the air
like standard dry erase particles do. Use a rag or small handheld vacuum to
occasionally clean your workspace of fallen ink flakes.
Turning-On
2
1
3
6
4
5
7
8
9
10
11
Flip the On/offPower Switch to provide
power to the glass lighting system.
Using Neon Pens
2
1
3
7
4
5
6
8
9
10
11
Before writing on the glass, turn the Glass Lights
dial (found on the Control Panel) to its maximum
setting by rotating it clockwise.
!
Choosing the right background is essential, because it will appear in the wide angle camera’s field of
view. Any light sources will make it harder to read the glowing ink. Furthermore, it is best to use eGlass
against a background that is free from clutter to minimize distractions. "
For a strikingly dramatic look, use a dark backdrop (such as a black sheet pinned to the wall with
thumbtacks). This will make the ink glow vividly against the black background.
Ink Writing
Ink Writing
Ink Writing
Ink Writing
Ink Writing
Ink Writing
Window in Background
Lights in Background
Ink Not Visible
Window Covered
Lights Removed
Ink Visible
Black backdrop
Cleanest background
Ink Highly Visible
BAD
GOOD
BEST
Setting Background
2
1
3
8
4
5
6
7
9
10
11
!
The objectives when calibrating lighting:"
•Reduce background brightness as much as possible."
•Maximize ink brightness so that it stands-out in contrast against the now-darkened background."
•Ensure instructor is properly lit so that viewers can see the instructor's face.
Calibrating Lighting
2
1
3
9
4
5
6
7
8
10
11
Calibrating the Lighting is one of the most important steps when setting up eGlass. When properly
calibrated, the lighting settings will make the ink glow vividly. eGlass features exposure controls that
allow it to be used in bright rooms. Even a white wall can be made darker by lowering the exposure
eGlass exposure.
Note: Before calibrating lighting, you need to have the software installed and running on you computer so
that you can see the eGlass image. You also need to active a neon pen and prepare to write on the glass.
Before Calibrating Lighting
•Background is bright "
•Ink does not glow against background"
•Instructor is not illuminated
After Calibrating Lighting
•Background is dark "
•Ink glows vividly against background"
•Instructor is illuminated
!
Continue Adjusting: Lighting should be constantly optimized by adjusting the Exposure +/- and
Instructor Lights according to the following balancing rule: "
If the image is too bright and you Lower the Exposure⬇, you may need to Raise the Instructor Lights⬆
Inversely, if the image is too dark and you Raise the Exposure⬆, you may need to Lower the Instructor Lights⬇
Step 2
Next, lower camera exposure by
pressing ( Exposure - ) until BOTH
the background and user are dark,
but the ink is still bright and visible.
Step 1
Turn the Glass Lights to 100% and
draw on the glass with an activated
Neon Pen.
Step 3
The previous step may have made
the user’s face too dark to be
visible, so slowly raise Instructor
Lights until the user is illuminated.
The image settings are adjusted from the Control Panel at the base of eGlass frame:"
Exposure + and Exposure - adjust how much light is let into the camera, effectively raising or lowering the the
entire image brightness. Even if your background is white wall, you can lower the exposure to make the
background appear darker, resulting in the ink glowing more vividly against the darker image. If the image is too
dark, you can raise the exposure to make the image appear brighter.
The Glass Lights control how bright the ink glows. The glass lights should always be set to 100% when using
neon markers."
The Instructor Lights illuminate the instructor. These should be increased as the exposure is lowered.
For the Best Results, Use a Dark Backdrop (Optional)
A dark backdrop (not included), such as a black fabric photography
backdrop, will provide the most dramatic look. These backdrops can be
purchased online and hung with thumbtacks, curtain rods, or other
mounting methods.
!
It is possible for light sources behind the camera to reflect offof the eGlass surface back into the camera.
These bright spots can be distracting and even make the glowing ink hard to see. For best results:"
1) Positioning: Do not position eGlass opposite of light sources that can reflect offof the glass (ceiling
light fixtures, windows, etc.). Try repositioning eGlass by turning it away from potential light sources."
2) Eliminate light sources at the source by closing curtains, powering-offlights, etc."
3) Lower Exposure (-) to reduce the intensity of reflections"
4) Hood: Use the Anti-Reflection Hood to fully eliminate reflections
Other Bright
Lights
Windows
Eliminating Reflections
2
1
3
10
4
5
6
7
8
9
11
Antireflection Hood
The included Antireflection Hood can be assembled and attached to the eGlass frame to block out any
reflections coming from the backside (camera side) of eGlass. "
Please note: Because the Antireflection Hood decreases visibility through the glass during face-to-face
instruction, try the other reflection elimination methods before using this solution when teaching face-to-face.
19
20
18
19
20
1. Insert the 4x Rods into the 2x Brackets"
2. Slide the Hood onto the 4x Rods,
ensuring each rod slides into the small pockets
18
18
Andere Handbücher für eGlass
2
Inhaltsverzeichnis
Beliebte Whiteboard Handbücher anderer Marken
EGAN
EGAN GlassWrite TableScreen TSG Bedienungsanleitung
Claridge
Claridge Edify Mobile Bedienungsanleitung
Legamaster
Legamaster e-Board Touch 2 Bedienungsanleitung
Nureva
Nureva WALL Bedienungsanleitung
Best-Rite
Best-Rite Black Splash Bedienungsanleitung
Da-Lite
Da-Lite Cosmopolitan Electrol Bedienungsanleitung