Patton electronics DIAMONDLINK 3201 Bedienungsanleitung

DiamondLink™ Model 3201 & 3241

G.SHDSL Router

Quick Start Guide

Important

—This is a Class A device and is intended for use in a light industrial environment. It is not

intended nor approved for use in an industrial or residential environment.

Document Number: 03321U7-001 Rev. B

Part Number: 07M3201-QS

Revised: October 15, 2008

Sales Ofﬁce: +1 (301) 975-1000

Technical Support: +1 (301) 975-1007

E-mail: [email protected]

WWW: www.patton.com

DiamondLink 3201 & 3241 Quick Start Guide

1.0 Power up the router

Your G.SHDSL router comes with one of the following power supply options:

•

External AC adaptor with included power cord

•

External DC power supply

1.1 Models with external AC adaptor

Connect female plug of the AC power cord to the AC adaptor provided.

Connect the barrel-type connector of the AC adaptor to the

Power

connector on the DiamondLink router.

Insert the male plug of the AC power cord into an AC power outlet (100–240 VAC).

•

This device contains no user serviceable parts. The equipment

shall be returned to Patton Electronics for repairs, or repaired

by qualiﬁed service personnel.

•

The external power adapter shall be a listed Limited Power

Source. The mains outlet that is utilized to power the devise

shall be within 10 feet (3 meters) of the device, shall be easily

accessible, and protected by a circuit breaker.

•

If an AC power adapter is used, ensure that the power cable

used meets all applicable standards for the country in which it

is to be installed, and that it is connected to a wall outlet which

has earth ground.

•

Hazardous network voltages are present in WAN ports regard-

less of whether power to the unit is ON or OFF. To avoid electric

shock, use caution when near WAN ports. When detaching the

cables, detach the end away from the device ﬁrst.

•

Do not work on the system or connect or disconnect cables

during periods of lightning activity.

The interconnecting cables shall be acceptable for external use and shall be rated for

the proper application with respect to voltage, current, anticipated temperature, ﬂam-

mability, and mechanical serviceability.

WARNING

CAUTION

DiamondLink 3201 & 3241 Quick Start Guide

Figure 1.

48VDC power supply

1.2 Models with external DC power supply

Strip insulation 1/4-inch from the electrical wires that will connect the DC power source to the 48VDC

power supply terminal block (see

ﬁgure 1

Connect the negative (-) terminal from the power source with to the negative (-) terminal on

the power supply.

Connect the positive (+) terminal from the power source with to the positive (+) terminal on

the power supply

Connect the 48VDC output barrel-type plug to the

Power

connector on the DiamondLink.

1.3 Power-up indication

The

Power

LED blinks as the DiamondLink is powering up. When the

Power

LED stops blinking and remains lit,

the DiamondLink is ready for you to conﬁgure.

2.0 Conﬁgure the IP address

The DiamondLink is shipped with a factory-conﬁgured IP address assigned to the

Ethernet

LAN port (green out-

line). The address is

192.168.200.10/24

. In most cases, you must change the address to be on the same subnet

as your PC, as described in the procedures below. If you are not sure which IP address to use for your installa-

tion, contact your network administrator.

Input: 36–60VDC, 0.13A

(SELV)

( + N/C - )

48VDCPower Supply

Module

Output: 5V, 1A( Ctr +)

Input: 36–60VDC, 0.13A

(SELV)

( + N/C - )

Power Su

Terminal

block

(-) Terminal

(+) Terminal

DiamondLink 3201 & 3241 Quick Start Guide

2.1 Connect a PC and log in

Using the included combination RS232/Ethernet cable and DB9-RJ45 adapter, connect a PC’s serial port

to the on the DiamondLink’s (red)

Console

port (see

ﬁgure 2

Figure 2.

Connecting DiamondLink to the PC’s serial port

Start a HyperTerminal session on the PC using the settings:

9600 bps, 8 data bits, 1 stop bit, no parity, no ﬂow control

superuser

Password: superuser

2.2 Modify the IP address

Display current IP interface settings for the DiamondLink

Ethernet

LAN port.

→→

ip list interfaces <enter>

IP Interfaces:

ID | Name | IP Address | DHCP | Transport

---|------|----------------|----------|--------------

1 | ip1 | 192.168.200.10 | disabled | <bridge>

----------------------------------------------

------

Modify the IP address for the LAN port according to your network requirements.

→→

ip set interface ip1 ipaddress 10.10.10.5 255.255.255.0

Note

The above IP address (

10.10.10.5/24)

is only an example. You must choose an IP address on the same

subnet as your PC

Verify the new address is correct and save it in system boot memory.

→→

ip list interfaces <enter>

→→

system config save <enter>

→→

Power Console Ethernet Line

MDI-X

Connect to Console port

(red port)

Serial port

PC with

terminal emulator

DiamondLink 3201 & 3241 Quick Start Guide

3.0 Connect to the local IP network

Now you can connect the DiamondLink to your local IP network and complete the remaining conﬁguration from

your PC using a standard web browser.

Connect the DiamondLink’s (green)

Ethernet

port to the same Ethernet segment as your PC (see

ﬁgure 3

). Press

the MDI-X switch until the

Ethernet Link

LED turns on.

Figure 3.

Connecting the DiamondLink to the local IP network

You can check the network connection with the ping command. For example, you would ping

10.10.10.5

from

your PC.

4.0 Log onto the web management interface

You will now access the web management Graphical User Interface (GUI) to conﬁgure the DiamondLink using a

standard web browser (such as Internet Explorer or Netscape browser).

At your PC, open a web browser and enter the IP address you assigned to the DiamondLink’s Ethernet

LAN port in step 2 of section

2.2 “Modify the IP address”

on page 4.

superuser

and the password

superuser

Figure 4.

DiamondLink web management home page

Power Console Ethernet Line

MDI-X

Connect to Ethernet port

(green port)

Ethernet port

MDI-X switch

DiamondLink 3201 & 3241 Quick Start Guide

5.0 Connect the G.SHDSL port

Obtain single-twisted-pair cable with an RJ-11 plug connector at each end.

Plug one end of the cable into the RJ-11socket (yellow colored port labeled

LINE

)

on the

DiamondLink Router.

Plug the other end of the cable into the RJ-11 wall socket that provides your G.SHDSL service.

When a DSL link is established, the front panel

WAN Link

LED will turn on.

6.0 Additional Information

Refer to the

DiamondLink User Manual

located on the CD-ROM shipped with your Model 3201 or 3241 and

available online at www.patton.com/manuals for detailed information about:

•

Installing, conﬁguring, operating, and troubleshooting,

•

Warranty, trademark, & compliance

A.0 Customer and Technical Support

Toll-Free VoIP support: call

sip:[email protected]

with a VoIP SIP phone

Online support: www

.patton.com

E-mail support:

[email protected]

—answered within 1 business day

Telephone support:

•

Standard: +1 (301) 975-1007 (USA), Monday–Friday: 8:00 am to 5:00 pm EST (1300 to

2200 UTC/GMT)

•

Alternate: +41 (0)31 985 25 55 (Switzerland), Monday–Friday: 8:00 am to 5:00 pm CET (0900 to 1800

UTC/GMT)

Fax:

+1 (253) 663-5693

(USA)

or +41 (0)31 985 25 26 (

Switzerland)

DiamondLink 3201 & 3241 Quick Start Guide

B.0 Compliance Information

B.1 Compliance

EMC:

•

FCC Part 15, Class A

•

EN55022, Class A

•

EN55024

Safety:

•

UL 60950-1/CSA C22.2 N0. 60950-1

•

IEC/EN60950-1

•

AS/NZS 60950-1

PSTN Regulatory:

•

FCC Part 68

•

CS-03

•

AS/ACIF S043:2003

B.2 FCC Part 68 (ACTA) Statement

This equipment complies with Part 68 of FCC rules and the requirements adopted by ACTA. On the bottom side of

this equipment is a label that contains—among other information—a product identiﬁer in the format

US:

AAAEQ##TXXXX

. If requested, this number must be provided to the telephone company.

The method used to connect this equipment to the premises wiring and telephone network must comply with the

applicable FCC Part 68 rules and requirements adopted by the ACTA.

If this equipment causes harm to the telephone network, the telephone company will notify you in advance that

temporary discontinuance of service may be required. But if advance notice isn’t practical, the telephone com-

pany will notify the customer as soon as possible. Also, you will be advised of your right to ﬁle a complaint with

the FCC if you believe it is necessary.

The telephone company may make changes in its facilities, equipment, operations or procedures that could

affect the operation of the equipment. If this happens the telephone company will provide advance notice in

order for you to make necessary modiﬁcations to maintain uninterrupted service.

If trouble is experienced with this equipment, for repair or warranty information, please contact our company. If

the equipment is causing harm to the telephone network, the telephone company may request that you discon-

nect the equipment until the problem is resolved.

Connection to party line service is subject to state tariffs. Contact the state public utility commission, public ser-

vice commission or corporation commission for information.

DiamondLink 3201 & 3241 Quick Start Guide

2.3 Industry Canada Notice

This equipment meets the applicable Industry Canada Terminal Equipment Technical Speciﬁcations. This is con-

ﬁrmed by the registration number. The abbreviation, IC, before the registration number signiﬁes that registra-

tion was performed based on a Declaration of Conformity indicating that Industry Canada technical

speciﬁcations were met. It does not imply that Industry Canada approved the equipment.

This Declaration of Conformity means that the equipment meets certain telecommunications network protective,

operational and safety requirements. The Department does not guarantee the equipment will operate to the

user's satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to

the facilities of the local telecommunications company. The equipment must also be installed using an acceptable

method of connection. In some cases, the company’s inside wiring associated with a single line individual service

may be extended by means of a certiﬁed connector assembly (telephone extension cord). The customer should

be aware that compliance with the above condition may not prevent degradation of service in some situations.

Repairs to some certiﬁed equipment should be made by an authorized maintenance facility designated by the

supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give

the telecommunications company cause to request the user to disconnect the equipment. Users should ensure for

their own protection that the ground connections of the power utility, telephone lines and internal metallic water

pipe system, are connected together. This protection may be particularly important in rural areas.

B.4 Radio and TV Interference (FCC Part 15)

This equipment generates and uses radio frequency energy, and if not installed and used properly—that is, in

strict accordance with the manufacturer's instructions—may cause interference to radio and television recep-

tion. This equipment has been tested and found to comply with the limits for a Class A computing device in accor-

dance with the speciﬁcations in Subpart B of Part 15 of FCC rules, which are designed to provide reasonable

protection from such interference in a commercial installation. However, there is no guarantee that interference

will not occur in a particular installation. If the equipment causes interference to radio or television reception,

which can be determined by disconnecting the cables, try to correct the interference by one or more of the fol-

lowing measures: moving the computing equipment away from the receiver, re-orienting the receiving antenna,

and/or plugging the receiving equipment into a different AC outlet (such that the computing equipment and

receiver are on different branches).

B.5 EC Declaration of Conformity

Product Description:

DiamondLink™ Models 3201 & 3241

We certify that the apparatus identiﬁed above conforms to the requirements of Council Directive 1999/5/EC on

the approximation of the laws of the member states relating to Radio and Telecommunication Terminal Equip-

ment and the mutual recognition of their conformity.

The signed Declaration of Conformity can be downloaded from

www.patton.com/certiﬁcations/

The safety advises in the documentation accompanying the products shall be obeyed. The

conformity to the above directive is indicated by the CE sign on the device.

DiamondLink 3201 & 3241 Quick Start Guide

B.6 Authorized European Representative

D R M Green

European Compliance Services Limited.

Avalon House, Marcham Road

Abingdon,

Oxon OX14 1UD, UK

10 DiamondLink 3201 & 3241 Quick Start Guide

The information in this document is subject to change without notice. Patton Electronics assumes no

liability for errors that may appear in this document.

Trademarks statement

The term DiamondLink is a trademark of Patton Electronics Company. All other trademarks presented in this doc-

ument are the property of their respective owners.

Warranty, Trademark, & Compliance Information

For warranty, trademark and compliance information, refer to the DiamondLink 3201 & 3241 User Manual

located on the CD-ROM that came with your router or available online at www.patton.com.

In accordance with the requirements of council directive 2002/96/EC on Waste of

Electrical and Electronic Equipment (WEEE), ensure that at end-of-life you separate

this product from other waste and scrap and deliver to the WEEE collection system in

your country for recycling.

Andere Handbücher für DIAMONDLINK 3201

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Patton electronics Netzwerk-Router Handbücher

Patton electronics

Patton electronics SMARTNODE 4630 Series Bedienungsanleitung

Patton electronics

Patton electronics SMARTNODE 4110 Series Bedienungsanleitung

Patton electronics

Patton electronics 2112 Bedienungsanleitung

Patton electronics

Patton electronics SmartNode 4900 Series Bedienungsanleitung

Patton electronics

Patton electronics 3224 Diamond Edge Bedienungsanleitung

Patton electronics

Patton electronics OnSite 2884 Bedienungsanleitung

Patton electronics

Patton electronics 3210 Bedienungsanleitung

Patton electronics

Patton electronics IM 1/I Bedienungsanleitung

Patton electronics

Patton electronics OnSite 3210 Series Bedienungsanleitung

Patton electronics

Patton electronics SmartNode 4520 Series Bedienungsanleitung

Patton electronics

Patton electronics 3087 Bedienungsanleitung

Patton electronics

Patton electronics SMART NODE 4950-NCE Bedienungsanleitung

Patton electronics

Patton electronics SmartNode 4960 Series Bedienungsanleitung

Patton electronics

Patton electronics ONSITE 2621 Bedienungsanleitung

Patton electronics

Patton electronics 4110 Series Bedienungsanleitung

Patton electronics

Patton electronics SMARTNODE 4552 Bedienungsanleitung

Patton electronics

Patton electronics SmartNode 4960 Series Bedienungsanleitung

Patton electronics

Patton electronics 4020 Series Bedienungsanleitung

Patton electronics

Patton electronics Patton IPLink 2603 Bedienungsanleitung

Patton electronics

Patton electronics IM2RC/IA Bedienungsanleitung

Patton electronics

Patton electronics SmartNode 4520 Series Bedienungsanleitung

Patton electronics

Patton electronics IpLink 2884 Bedienungsanleitung

Patton electronics

Patton electronics IPROCKETLINK 3101 Bedienungsanleitung

Patton electronics

Patton electronics OnSite 2884 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise