PCE Instruments PCE-JR 911 Bedienungsanleitung

INSTRUCTION MANUAL

PCE-JR 911

PCE Americas Inc.

711 Commerce Way

Suite 8

Jupiter

FL-33458

USA

From outside US: +1

Tel: (561) 320-9162

Fax: (561) 320-9176

[email protected]

www.pce-instruments.com/english

www.pce-instruments.com

PCE Instruments UK Ltd.

Units 12/13

Southpoint Business Park

Ensign way

Hampshire / Southampton

United Kingdom, SO31 4RF

From outside UK: +44

Tel: (0) 2380 98703 0

Fax: (0) 2380 98703 9

[email protected]

HVAC Meter

INSTRUCTION MANUAL....................................................................................................1

1.Introduction.....................................................................................................................3

2.Material Supplied............................................................................................................3

3.Features...........................................................................................................................3

3.1 IR thermometer with laser targeting.....................................................................................................3

3.2 Procedure Programming Function .......................................................................................................4

3.3Datalogger Function..................................................................................................................................5

4.Comparison Table...........................................................................................................5

5.Front View........................................................................................................................6

6.Paper Replacement.........................................................................................................7

7.Battery Replacement......................................................................................................7

8.FUNCTION-IR thermometer with laser targeting..........................................................9

9. FUNCTION-Procedure programming...........................................................................9

10. FUNCTION-Data logger .............................................................................................10

11.FUNCTION-Setting Parameters .................................................................................14

12.FUNCTION-Link with PC.............................................................................................15

1.Introduction

Thank you for purchasing this IR Meter Printer This unit has been developed to meet

your maximum satisfaction with its user-friendly design.Please review the entire

manual for a complete overview of how to operate this new IR Meter Printer

2.Material Supplied

Check for damaged or missing parts in your IR Meter Printer before starting.

The IR Meter Printer Set should contain

1. Meter

2. 4pcs AA batteries 3. Printing Paper

4. Operation manual

3.Features

This IR Meter Printer equipped with three functions:

•IR thermometer with laser targeting.

•Procedure programming function.

•Data logger function.

Please refer to below features of each function for clear understanding.

3.1 IR thermometer with laser targeting

Temperature Range -40 ~ 500

Resolution 0.1 unit (<100 ) or

1 unit; Unit is or .

Accuracy +/- 3% or 3

(Whichever is greater)

Repeatability +/- 1

Emissivity Adjustable from

0.3 ~ 1.0

Response time 0.2 seconds

Backlight / Laser sighting Yes / Yes

Distance Ratio 8:1

Printer

Interface with PC

38 mm Thermal-Printer

(30mm x 30 thermal

paper)

RS-232C (TTL level) *

Power supply AA x4 Battery or DC

9V, 1000mA adaptor,

w/ 5.5 x 2.0mm Center

plug Center is positiv

Operating current 500mA(Printing),

6mA(IR active),

2mA(IR standby)

Auto. Power off No operation for 10

seconds at normal mod

60 seconds for others

mode.

Operation temperature 0 - 50

Operation humidity Less then 90%RH

Dimension 208 x 70 x 53 mm

Remarks:

* Software for downloading data to PC is optional.

3.2 Procedure Programming Function

Procedure capacity: 4 procedures in total. Indicated as #1 to #4 with procedure name.

Measure point: 99 measure points in each procedure.

Measure point content Each measure point consists of point number point name and

temperature value.

3.3Datalogger Function

Data logger capacity 4 data logger settings. Indicated by #5 to #8

Data logger setting Setting by Begin Date End Date Start Time Suspend Time Rate

**.99 measure points in each data logger setting

Measure point Each measure point consists of point number point title and

temperature value.***

Remarks:

**Rate means the time period to get the temp. Value.For example "20" means getting

temp. value every 20 seconds during "Start Time" and " Suspend Time".

***Point name consisted by logging's date & time automatically.

4.Comparison Table

Function Procedure Logger

Number #1 to #4 #5 to #8

Name User defined or automatic Automatic

(Note 1) (Note 2)

Measuring/ User pressed Automatic measure and store

Sampling by specified setting by user(Note 3).

Max point 99 99

ON key to measure,

then press enter key

to confirm/store.

Note 1: Meter automatic defines title

if user doesn't key-in any. The name is consisted by current date and time. For

example if point name is "05-06 09:21:51" means the date is 6th May and the time is

09:21:51.

Note 2: Meter automatic defines the name of the measured point by current date and

time.

Note 3: Logger setting defined by Start-Date, Begin-time, Suspend-time, End-Date,

and sample rate. Each logger starts from Start-Date & time, sampling by specified

rate until Suspend-time. Start again next day until End-Date.

Logger is stopped by reaching End-Date or 99 points or press "0" key twice.

5.Front View

6.Paper Replacement

For feed paper and confirming setting. Feed the paper when it's held down except

printing. Please follow the pictures to scissor out a paragraph from supplied printing

paper To make easier feeding the paper insert the sharp-cut to the cartidge of the

printer. Keep the matt surface of the paper upward when inserting the paper

7.Battery

Replacement

When seeing the battery symbol flashing on the right-up corner of the LCD means the

batteries are weak.

If the power is too low to operate the IR printer, printer will reset with below indication

on LCD monitor.

Follow the steps to remove and replace batteries

1. Open the batteries set cover on the rear side.

2. Remove the expired batteries.

3. Insert new 4pcs AA batteries and make sure the batteries are inserted with correct

polarity.

4. Put on the cover.

8.FUNCTION-IR thermometer with laser targeting

1.Press "ON" key to enter IR mode. LCD will display real-time target temperature until

"ON" key released. After releasing the "ON" key, LCD will hold the last value for 10

seconds and then auto power off.

2.Press "ON" key and " " key at the same to in-active the laser targeting while

measure the temperature. Once releasing the " " key, laser targeting function

activated again.

3.Press "PRINT" key to print out current value date and time.

9. FUNCTION-Procedure programming

1. Press "PROC" key to enter procedure mode.

2. There are #1to #4 procedures included in this function.Press "SET" key to select

the procedure number you want.If selecting #3 LCD will display as below

3.How to name the procedure?

Make sure the procedure number you choose has been highlight.Press "ENTER"

key one time and the highlight will start flashing Editing function is valid only when

above highlight is flashing.Pressing alphanumeric keys to edit the name release the

alphanumeric keys when you select the word you need.Press "0" key for a space or

press" " for forward " " for backward.Press "ENTER" key to finish and store the

editing.

4.How to name the measured point? First of all press" " or " " to find the point you

need Press"1" to quickly skip to 10 11 or press "2" to skip to 20 21.... Or press"9" to

skip to 90 91 etc.

The point naming procedure is the same as "How to name the procedure" section.

Meter will also automatic store current date and time as point name if user didn't edit

any.

5.Press "ON" to get the current temperature and then press "ENTER" to save the

value User will see the LCD shown as below

6.Press "PRINT" to print out

procedure saved data "Print?" will appear on LCD If OK press "PRINT" again to

continue If NO press "PROC" to back to procedure function. Please refer to below for

the printed out data.

7.How to delete data

Press "PROC" key at least 2 seconds to clear procedure name point name or

temperature value

10. FUNCTION-Data logger

1.Press "LOG" key to enter data logger mode.

2.There are #5to #8 loggers included in this function Press "SET" key to select the

data logger number you want. If selecting #7 LCD will display as below

3.How to set the data logger parameters?

Press " " for forward and " " for backward to choose the parameters. Pressing

alphanumeric keys to modify the parameters one by one.Press "ENTER" key to start

the data logger.

Inhaltsverzeichnis

Andere PCE Instruments Messgerät Handbücher

PCE Instruments

PCE Instruments SIMCO FMX-003 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-TTC 30 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-TDS 100 HS Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-TG 250 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-HT 110 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-TDS 200 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-DC1 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-CL 10 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-FM 1000 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-432-ICA Bedienungsanleitung

PCE Instruments

PCE Instruments LMD 5 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-228LIQ Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-VT 1000 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-TDS 200 Series Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-LDM 45 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-910 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-MSR 150 Bedienungsanleitung

PCE Instruments

PCE Instruments PT-DPM Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-CT 21BT Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-TG 300-NO7 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-TA 30 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-423 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-PTR 200N Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-PTH 10 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung