PCE Instruments PCE-TG 250 Bedienungsanleitung

PCE-TG 250 / Manual

TECHNICAL DATA

DISPLAY 128X64 PIXEL LCD WITH BACK LIGHT

MEASURMENT RANGE

- STANDARD 1.0 mm TO 250 mm IN STEEL DEPENDING OF THE PROBE

- THROUGH COATING 4 mm –18 mm

TOLERANCE +/-0.02 mm IN STEEL

DISPLAY RESOLUTION 0.01 mm ( Less than 100.0 mm )

0.1 mm ( over 100 mm )

BULIT-IN STANDARD BLOCK 4.00 mm

VELOCITY RANGE 1000-9999 m/s

POWER 2 EA. 1.2 V AA BATTERY

OUTSIDE DIMENSION 149X73X32 mm

WEIGHT 350 g

FEATURES:

AUTOMATIC SELF CALIBRATION

COUPLANT INDICATOR

AUTOMATIC POWER OFF DEVICE

HIGH-LOW LIMIT ALARM

LCD BRIGHTNESS ADJUST

THROUGH COATING CAPABILTY

THROUGH COATING MEASUREMENT

500 DATA READING STORAGE WITH DIFFERENT 5 MEMORY FILES

LOW BATTERY INDICTOR

INTRODUCTION OF THE GAUGE

OPERATING PROCEDURE

STANDARD MODE:

1. INSTRUMENT AND PROBE

PLUG THE PROBE TO THE THICKNESS GAUGE CONNECOTR. PRESS KEY, HEAR BI-BI

SOUND THEN LCD DISPLAY TURN ON AND DISPLAY THE LAST SET VERLOCITY. DISPLAY AS FOLLOWING

THICKNESS GAUGE SYSTEM SETTING

SYSTEM SETUP

PRESS GAUGE KEY TURN ON THE GAUGE, LCD WILL DISPLAY

PRESS MENU KEY 2 TIME. THEN PRESS ENTER KEY , DISPLAY FOLLOWING

System Setup

Function Setup

Outside alarm

[enter] to select

↓to down

PRESSS ENTER KEY AGAIN, DISPLAY FOLLOWING SCREEN

Units METRICS ( CAN PRESS SELECT INCH OR METRICS UNIT )

Resolution HIGH ( HIGH=HIGH RESOLUTION DISPLAY 0.01 mm )

Min Capture ON ( CAPTURE MIN MEASUREMENT THICKNESS )

2-Point CAL OFF ( OFF=SINGLE POINT AND ON=2-POINT CAL )

LANGUAGE ENGLISH

↓to down

USE KEY MOVE HIGH-LIGHT CURSOR UP AND DOWN. USE ENTER KEY TO CHANGE THE

SETTING

AFTER SETTING COMPLTED, PRESS MENU KEY 2 TIMES BACK TO THE MEASUREMENT FUNCTION

FUNCTION SETUP

PRESS GAUGE KEY TURN ON THE GAUGE, LCD WILL DISPLAY

PRESS ENTER 2-TIMES, PRESS ENTRY KEY, USE KEY MOVE HIGH LIGHT

CURSOR TO FUNCTION SETTING, PRESS THEN USE KEY MOVE HIGH-LIGHT CURSOR

DOWN TO THE FOLLOWING DISPLAY

Erase file

Erase all data

Erase cal data

[ENTER] to select

UP AND DOWN LIMIT ALARM SETTING

PRESS GAUGE KEY TURN ON THE GAUGE, LCD WILL DISPLAY

PRESS MENU KEY 2 TIME. PRESS KEY UNTIL HIGH-LIGHT CURSOR MOVE TO THE

OUTSIDE ALARM, THEN PRESS ENTER KEY, DISPLAY FOLLOWING

USE KEY TO ADJUST THE LOW LIMIT THICKNESS,

THEN PRESS ENTER TO SET HIGH LIMIT THICKNESS

AFTER SETTING, PRESS MENU 2-TIMES BACK TO THE MEASUREMENT FUCTION. WHEN THICKNESS

MEASUREMNT OVER THE RANGE 0.10 mm –200.0 mm, THE THICKNESS GAUGE BEBER START TO

ALARM.

2. VELOCITY SETTING

IF USER ALREADY KNOW THE MATERIAL VELOCITY. USER CAN USE MANUAL ADJUST THE

VELOCITY FROM REFERENCE CHART. THE GAUGE CAN STORED 5 DIFFERENT MATERIAL VELOCITY

IF THE DISPLAY VELOCITY IS NOT REQUIRED, THEN PRESS VEL KEY SELECT THE VELOCITY

FROM MEMORY, THEN PRESS ENTER KEY.

IF THE 5 STORGED VEL ARE NOT THE TEST MATERIAL VEL. THEN USE

KEY ADJUST THE VEL DISPLAY UNTIL MEET REQUIRED VEL. THEN USER CAN PREE

ENTER KEY STORE THIS VEL FOR MEASUREMENT THE SAME MATERIAL NEXT TIME

IF THE VEL IS UNKNOWN, USE THE TOOLS MEASURMENT THE TEST SPECIMEN THICKNESS. PUT

PROBE ON THE SPECIMEN. USE KEY ADJUST THE THICKNESS DISPLAY SAME AS

TOOLS MEASUREMNT.

PRESS VEL TO GET DISPLAY OF SPECIEMN VEL AND STORED THE VEL TO THE MEMORY.

PRESS VEL KEY ENTER VEL SETTING

PRESS VEL KEY AGAIN TO SELECT THE 2’NDSTORED VEL

USE KEY ADJUST THE VEL DISPLAY UNTIL MEET REQUIRED VEL

3. INSTRUMENT CALIBRATION

IT’S NECESSARY TO CALIBRATE WHEN CHANGE THE PROBE OR TURN ON THE INSTRUMENT.

DURING THE OPERATING, OPERATOR NEEDED FREQUENCY RETURN BACK AND CALIBRATION AGAIN.

SINGLE POINT CALIBRATION

SET THE VEL TO 5900 m/s, PUT SOME COUPLANT TO THE GAUGE SIDE BLOCK. PRESS THE

PROBE TO THE BLOCK, WAIT UNTIL COUPLANT INDICATOR NOT FLASH. PRESS CAL KEY, THE

DISPLAY WILL SHOW 4.00 mm.

TWO POINT CALIBRATION

TO GET MORE PRECISION MENSURMENT, TWO POINT CALIBRATION IS NECESSARY

GET A STEP BLOCK ( AT LEAST TWO DIFFERENT THICKNESS AND COVER THE MEASURMENT

RANGE.

PRESS MENU TWO TIME UNTIL CURSOR TO THE MENU PRESS ENTER , ENTER THE

SYSTEM SETTING MENU AS FOLLOWING

System Setup

Function Setup

Outside alarm

[enter] to select

↓to down

PRESS TO System Setup, then press key

PRESS KEY UNTIL DISPLY HIGH LIGHT AS FOLLOWING

Resolution: HIGH

Min Captyre: OFF

2-Point CAL: OFF

[enter] to select

↑TO UP ↓to down

PRESS ENTER KEY CHNANGE THE 2-POINT CAL: OFF INTO ON

Resolution: HIGH

Min Captyre: OFF

2-Point CAL: ON

[enter] to select

↑TO UP ↓to down

PRESS MANUAL BACK , THEN PRESS KEY AGAIN TO THE DISPLAY SCREEN.

PUT COUNPLAT ON THIN BLOCK, MOVE THE PROBE ON THE THIN BLOCK. PRESS CAL KEY,

DISPLAY SHOWTHE THIN BLOCK THICKNESS.

USE KEY TO ADJUST THE THIN THICKNESS DISPLAY UNTIL MEET BLCOK THICKNESS

VALUE. THEN PRESS CAL KEY AGAIN. DISPLAY

USE KEY TO ADJUST THE THICK THICKNESS DISPLAY UNTIL MEET BLCOK THICKNESS

VALUE. THEN PRESS CAL KEY AGAIN. COMPLETE THE 2-PINT CALIBRATION SETUP.

4. THICKNESS MEASUREMENT

AFTER CALIBRATE AND SETUP THE THICKNESS GAUEG, PUT SOME COUPLANT ON THE TEST

SPECIMEN. MOVE AND PRESS THE PROBE ON THE SPECIMEN, LCD NOW DISPLAY THE ACTIUAL

THICKNESS MEASUREMENT READING.

WHEN PROBE AND TEST SPECIMEN COUPLANT IS GOOD, THE DISPLAY WILL SHOW COUPLANT GOOD

INDICATOR. WHEN LIFT-OFF THE PROBE THE THICKNESS DISPLAY NO CHANGE BUT COUPLANT

INDICTOR DISAPPEAR.

5. LOW BATTERY INDICATOR

WHEN THICKNESS GAUGE POWER WAS NOT ENOUGH, THE LOW BATTERY INDICATOR WILL DISPLAY

ON THE LEFT BOTTOM ON DISPLAY LCD.

6. TURN POWER OFF THE THICKNESS GAUGE

UM-2D HAVE 2 WAYS TO TURN OFF THE POWER.

6.1 AUTO TURN OFF

-IF THE THICKNESS GAUGE WAIT 3 MIN NOT MEASUREMENT, THE THICKNESS GAUGE WILL

TURN-OFF AUTOMATICALLY

6.2 MANUAL TURN OFF

-PRESS MENU UNTIL HIGH LIGHT TO OFF INDICATOR, PRESS KEY TO TURN OFF THE

THICKNESS GAUGE

7. THICKNESS DATA STORAGE AND RECALL

7.1 THICKNESS DATA STORAGE

THE THICKNESS DATA CAN BE STORGED WITH 5 DIFFERENT FILE NAME. EACH FILE NAME CAN

STORGED 100 READING.

PRESS KEY, MOVE DISPLAY LCD HIGH LIGHT CUSOR TO SAVE1.

PRESS KEY CAN SELECT SAVE1, SAVE2,SAVE3, SAVE4, SAVE 5 FILE NAME

PUT PROBE ON THE SPECIMEN GET READING1, PRESS KEY. THE LEFT BOTTOM SIDE WILL

SHOW MEMORY, THIS MEAN, THE READING 1 ALREADY STORAGED IN THE FILE 1. CONTINOUS TO DO

THE STORAGE OF READING 2.3.4…..

7.2 THCINESS DATA RECALL

PRESS KEY, MOVE DISPLAY LCD HIGH LIGHT CUSOR TO SAVE1.

PRESS KEY CAN SELECT SAVE1, SAVE2,SAVE3, SAVE4, SAVE 5 FILE NAME

PRESS KEY. THE LCD DISPLAY

No.001 IS THE FILE NAME

Total: 005 MEANS FILE NAME No 1 HAVE 5 STORAGE DATA, USE KEY

TO CHANGE THE POINT READING

DELIETE

DELIETE THE SINGLE POINT READING

ENTER THE RECALL CONDITION

USE KEY TO CHANGE THE POINT READING, SELECT THE POINT WANT TO DELIETE.

PRESS KEY, DELIETE THIS POINT.

DELIETE THE WHOLE FILE

PRESS GAUGE KEY TURN ON THE GAUGE, LCD WILL DISPLAY

PRESS ENTER 2-TIMES, PRESS ENTRY KEY, USE KEY MOVE HIGH LIGHT

CURSOR TO FUNCTION SETTING, PRESS THEN USE KEY MOVE HIGH-LIGHT CURSOR

DOWN TO THE FOLLOWING SCREEN.

Erase file

Erase all data

Erase cal data

[ENTER] to select

PRESS , THE SCREEN DISPLAY

Press [ ENTER]

To confirm

Press [ MENU ]

to cancle

AFTER PRESS KEY, IT WILL SHOW ERASE FILE 1

Andere PCE Instruments Messgerät Handbücher

PCE Instruments

PCE Instruments UMI 840 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-228LIQ Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-PFG Series Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-DDA 10 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-DC 3 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-4-EKIT Series Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-MSV 10 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-DFG N Series Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-TDS 100 HS Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-TG200 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-HWA 30-ICA Bedienungsanleitung

PCE Instruments

PCE Instruments TDS-100H Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-TG 50 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-DFG NF Series Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-GPA 50 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-MMT E Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-TG 300-NO5 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-HMM Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-HFX 100 Bedienungsanleitung

PCE Instruments

PCE Instruments DFG N Series Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-SLT Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-WB 20SD Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-CT 5000 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-VT 3700-ICA Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung