PEERLESS Mounts SmartMount ST670 Leitfaden

ISSUED: 03-25-09 SHEET #: 202-9334-1

Installation and Assembly:

SmartMount®Universal Tilt Wall Mount for LCD and Plasma

Flat Panel Screens

Features:

• Screen held only 3" (76 mm) from wall for a discreet installation

• Wall plate design allows for wall acces allowing multiple cable management options

• Universal tilt brackets easily hook onto wall plate for fast installation

• Adjustable up to 15° of forward tilt and up to -5° backward tilt for optimal viewing angle

• One-touch tilt for effortless adjustment

• Pre-tensioned universal tilt bracket allows for tilt angle adjustment in one easy motion.

• Easy grip handle locks the screen position into place

• Optional IncreLok feature offers ﬁxed tilts at -5°, 0°, 5°, 10° and 15° increments

• Includes Sorted-For-You™ fastener pack for installation to wood studs, concrete, and cinder block

• Optional horizontal adjustment of up to 8" (203 mm) (depending on screen model) for perfect

screen placement

• Available in Black or Silver

USC

Model # Screen Size Range Max. Load Capacity

ST670, ST670P, ST670-S, ST670P-S,

SWS520/BK, SWS520/SI 42''- 71'' (107 - 180 cm) 250 lb (113 kg)

ST680, ST680P, ST680-S, ST680P-S 61''- 102'' (155 - 259 cm) 350 lb (159 kg)

2 of 18 ISSUED: 03-25-09 SHEET #: 202-9334-1

NOTE: Read entire instruction sheet before you start installation and assembly.

Table of Contents

Parts List.................................................................................................................................................................................3

Installation to Triple Wood Stud Wall......................................................................................................................................5

Installation to Solid Concrete or Cinder Block ........................................................................................................................6

Installing Tilt Brackets.............................................................................................................................................................7

Installing Flat Panel Screen to Wall Plate...............................................................................................................................9

• Do not begin to install your Peerless product until you have read and understood the instructions and warnings

contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US

customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact

your local distributor.

• This product should only be installed by someone of good mechanical aptitude, has experience with basic building

construction, and fully understands these instructions.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardware and components.

• Never exceed the Maximum Load Capacity. See page one.

• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of

an "edge to edge" stud ﬁnder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tighten screws ﬁrmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding

power.

• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal

injury.

• This product was designed to be installed on the following wall construction only;

WALL CONSTRUCTION HARDWARE REQUIRED

• Wood Stud Included

•Wood Beam Included

•Solid Concrete Included

•Cinder Block Included

• Metal Stud Do not attach except with Peerless Metal Stud Accessory Kit - ACC615;

• Brick Contact Qualiﬁed Professional

• Other or unsure? Contact Qualiﬁed Professional

WARNING

Tools Needed for Assembly

•stud ﬁnder ("edge to edge" stud ﬁnder is recommended)

• phillips screwdriver

•drill

• 5/16" (8 mm) bit for concrete and cinder block wall

• 5/32" (4 mm) bit for wood stud wall

• level

3 of 18 ISSUED: 03-25-09 SHEET #: 202-9334-1

Parts may appear slightly different than illustrated.

Before you begin, be sure all parts shown are included with your product.

Adapter Bracket Fasteners

M4 x 12 mm (4)

(504-9013)

M6 x 25 mm (4)

(520-1208)

M4 x 25 mm (4)

(504-1015)

M5 x 25 mm (4)

(520-9543)

M6 x 12 mm (4)

(520-1128)

M5 x 12 mm (4)

(520-1027)

.5" spacer (4)

(540-1057)

.75" spacer (4)

(540-1059)

M8 x 16 mm (6)

(520-9257)

M8 x 40 mm (4)

(520-1136)

multi-washer (4)

(580-1036)

M8 x 25 mm (4)

(520-1031)

M6 x 20 mm (4)

(520-9402) M6 x 30 mm (4)

(510-9109)

Parts List

Description Qty.

ST680

ST670

ST680-S

ST670-S

SWS520/BK

ST680P

ST670P

SWS520/SI

ST680P-S

ST670P-S

XX AAwall plate 1 200-1901 200-4901 200-1901 200-4901

XX 200-1902 200-4902 200-1902 200-4902

XX BBleft tilt bracket 1 201-1474 201-4474 201-1473 201-4473

XX 201-1480 201-4480 201-1477 201-4477

XX CCright tilt bracket 1 201-1476 201-4476 201-1475 201-4475

XX 201-1478 201-4478 201-1479 201-4479

XXXXDD#14 x 63.5 mm wood screw 6 5S1-015-C03 5S1-015-C03 5S1-015-C03 5S1-015-C03

XXXXEEconcrete anchor 6 590-0320 590-0320 590-0320 590-0320

XXFF4 mm allen wrench 1 560-1146 560-1146 - -

ST670P, ST670P-S,

SWS520/BK,

SWS520/SI

ST680P, ST680P-S

ST670, ST670-S

ST680, ST680-S

4 of 18 ISSUED: 03-25-09 SHEET #: 202-9334-1

M4 x 12 mm (6)

(510-1079) M5 x 12 mm (4)

(520-1064)

M5 x 25 mm (4)

(520-1122)

M6 x 25 mm (4)

(520-1211)

M4 x 25 mm (4)

(510-1082)

M6 x 12 mm (4)

(520-1050) M8 x 15 mm (6)

(520-1068)

M8 x 40 mm (4)

(520-1152)

I.D. .34" (8.6 mm) (4)

(540-1059)

I.D. .22" (5.6 mm) (4)

(540-1057)

multi-washer (6)

(580-1036)

M6 x 20 mm (4)

(520-9554)

M6 x 30 mm (4)

(520-1067)

M8 x 25 mm (4)

(520-1101)

Security Adapter Bracket Fasteners

5 of 18 ISSUED: 03-25-09 SHEET #: 202-9334-1

Installation to Triple Wood Stud Wall

Wall plate (AA) can be mounted to three studs that are 16" apart. Use a stud ﬁnder to locate the edges of the studs.

Use of an edge-to-edge stud ﬁnder is highly recommended. Based on their edges, draw a vertical line down each

stud’s center. Place wall plate on wall as a template. The top mounting slots should be 2.5" (64 mm) above the

desired screen center as shown in ﬁgure 1.1. Level plate, and mark the center of the six mounting holes. Make sure

that the mounting holes are on the stud centerlines. Drill six 5/32" (4 mm) dia. holes 2.5" (64 mm) deep. Make sure

that the wall plate is level, secure it using six #14 x 63.5 mm wood screws (DD) as shown in ﬁgure 1.2.

Skip to step 2.

NOTE: Wall plate may be mounted up to 6" (152 mm) off center as shown in ﬁgure 1.1.

ﬁg. 1.2

• Installer must verify that the supporting surface will safely support the combined load of the equipment and all

attached hardware and components.

• Tighten wood screws so that wall plate is ﬁrmly attached, but do not overtighten. Overtightening can damage the

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud ﬁnder

is highly recommended.

• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Install-

ers are responsible to provide hardware for other types of mounting situations (not UL approved).

WARNING

CS = center of screen ﬁg. 1.1

STUD

(152 mm)

2.5"

(64 mm)

(152 mm)

6 of 18 ISSUED: 03-25-09 SHEET #: 202-9334-1

Installation to Solid Concrete or Cinder Block

Make sure that wall plate (AA) is level, use it as

a template to mark four mounting holes. The top

mounting hole should be 2.5" (64 mm) below the

desired screen center as shown in ﬁgure 1.1 on page

5. Drill four 5/16" (8 mm) dia. holes to a minimum

depth of 2.5" (64 mm). Insert anchors (EE) in holes

ﬂush with wall as shown (right). Place wall plate over

anchors and secure with #14 x 63.5 mm screws (DD).

Level, then tighten all fasteners.

• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" (35 mm) of actual

concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount

in a solid part of the block, generally 1" (25 mm) minimum from the side of the block. Cinder block must meet ASTM

C-90 speciﬁcations. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a

hammer drill to avoid breaking out the back of the hole when entering a void or cavity.

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Make sure that the wall will safely support four times the combined load of the equipment and all attached hardware

and components.

WARNING

• Always attach concrete expansion anchors directly

to load-bearing concrete.

• Never attach concrete expansion anchors to

concrete covered with plaster, drywall, or other

ﬁnishing material. If mounting to concrete surfaces

covered with a ﬁnishing surface is unavoidable,

the ﬁnishing surface must be counterbored as

shown below. Be sure concrete anchors do not

pull away from concrete when tightening screws. If

plaster/drywall is thicker than 5/8" (16 mm), custom

fasteners must be supplied by installer.

WARNING

• Tighten screws so that wall plate is ﬁrmly attached,

but do not overtighten. Overtightening can damage

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

WARNING

CUTAWAY VIEW

INCORRECT CORRECT

wall

plate

wall

plate

plaster/

drywall

plaster/

drywall

concrete concrete

Drill holes and insert anchors (EE).

Place plate (AA) over anchors (EE) and secure with screws (DD).

Tighten all fasteners.

concrete

surface

AA EE

SOLID CONCRETE

CINDER BLOCK

7 of 18 ISSUED: 03-25-09 SHEET #: 202-9334-1

Attaching Tilt Brackets to Screen using Bafﬂed Fastener Pack

To prevent scratching the screen, set a cloth on a ﬂat, level surface that will support the weight of the screen. Place

screen face side down. Refer to screen manufacturers instructions or customer service, for removing any knobs,

base, cover, or screw(s) on the back of the screen to prepare mounting. These need to be removed to allow the

adapter brackets to be attached. Select the small, medium, large or extra large screws from the bafﬂed fastener

pack then attach tilt brackets to screen following ﬁgure 2.1 or 2.2.

NOTE: Be sure to attach tilt brackets with handle facing outward as shown below.

NOTE: Top and bottom mounting holes must be used for attaching brackets. Middle holes should also be used

where the fasteners and screens allow. Verify that all holes are properly aligned, and then tighten screws using a

phillips screwdriver.

• Tighten screws so adapter brackets are ﬁrmly attached. Do not tighten with excessive force. Overtightening

can cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to

become detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.

• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly

secured, damage may occur to screen or product may fail.

WARNING

CENTER BRACKETS VERTICALLY

ON BACK OF SCREEN

HANDLE FACE

OUT

Note: "X" dimensions should be equal.

NOTE: For ﬂat back screens proceed to step 2-1. For bump-out or recessed back screen skip to step 2-2.

MULTI-WASHER

MEDIUM HOLE FOR M5 SCREWS

SMALL HOLE FOR M4 SCREWS

LARGE HOLE FOR M6 SCREWS

Notes:

• The number of fasteners used will vary,

depending upon the type of screen.

• Multi-washers and spacers may not be used,

depending upon the type of screen.

• Use the corresponding hole in the multi-

washer that matches your screw size as

shown.

• Slots in ST680 models are wider and require

the use of the M8 washer.

8 of 18 ISSUED: 03-25-09 SHEET #: 202-9334-1

Refer to Screen Compatibility Chart to determine the proper fastener to use. Visit www.peerlessmounts.com/3

for ST670 models or www.peerlessmounts.com/4 for ST680 models for a full screen compatibility chart for this

mount.

Begin with the shortest length screw, hand thread through multi-washer and adapter bracket into screen as shown

below. Screw must make at least three full turns into the mounting hole and ﬁt snug into place. Do not over tighten.

If screw cannot make three full turns into the screen, select a longer length screw from the bafﬂed fastener pack.

Repeat for remaining mounting holes, level brackets and tighten screws.

NOTE: Spacers may not be used, depending upon the type of screen.

NOTE: If using M10 x 15 mm penta-pinTM screws, tighten screws with Penta-pinTM driver.

Refer to Screen Compatibility Chart to determine the proper fastener to use. Visit www.peerlessmounts.com/3

for ST670 models or www.peerlessmounts.com/4 for ST680 models for a full screen compatibility chart for this

mount.

Begin with longer length screw, hand thread through multi-washer, adapter bracket and spacer in that order into

screen as shown below. Screw must make at least three full turns into the mounting hole and ﬁt snug into place.

Do not over tighten. If screw cannot make three full turns into the screen, select a longer length screw from the

bafﬂed fastener pack. Repeat for remaining mounting holes, level brackets and tighten screws.

NOTE: If using M10 x 15 mm penta-pinTM screws, tighten screws with Penta-pinTM driver.

For Flat Back Screen

For Bump-out or Recessed Back Screen

ADAPTER

BRACKET

(BB or CC)

SCREEN

ﬁg. 2.1

SCREW

2-1

2-2

If you have any questions, please call Peerless customer care at 1-800-865-2112.

MULTI-WASHER

SCREEN

SCREW

ADAPTER

BRACKET

(BB or CC)

ﬁg. 2.2

SPACER

MULTI-WASHER

9 of 18 ISSUED: 03-25-09 SHEET #: 202-9334-1

For preset tilt angles use Increlok™ and for custom

tilt angle use ratchet handle.

INCRELOK™: The screen can be locked into a

pre-set tilt position of -5°, 0°, 5°, 10° or 15°. Use

locator hole to ﬁnd tilt position hole and tilt screen

to align holes. Tighten IncreLok™ tilt locking

screws on both tilt brackets to lock tilt as shown in

detail 2.

Ratchet Handle: Loosen ratchet handle (refer to

step 3 for tension adjustment of handle). Push or

pull from top or bottom of screen to adjust tilt as

shown in ﬁgure 4.1. The tilt can be adjusted to a

maximum of 15° forward or 5° backward.

Tension Adjustment of Ratchet Handle: Adjust

tension in tilt brackets (BB & CC) by rotating ratchet

handle. NOTE: If obstruction prevents ratchet handle

from rotating, pull handle out while turning will allow

handle to reposition without tightening. Release and

turn handle to tighten or loosen.

Mounting Screen: Ratchet handle must be in the

up or down position or interference will occur while

hooking tilt brackets to wall plate (AA). Slowly hook tilt

brackets (BB & CC) onto wall plate (AA) and swing

screen down as shown in ﬁg. 3.1. Tilt bracket hooks

must fully engage wall plate as shown in detail 1. Using

phillips screw driver/allen wrench (FF), turn safety

screws on tilt brackets (BB & CC) clockwise till screw

tip securely contacts wall plate as shown in cross

section.

Screen Adjustment: Screen can be adjusted

horizontally by loosening safety/security screws on

tilt brackets (BB & CC) three full turns. Adjust screen

as shown in ﬁgure 3.2. Tighten safety screws on tilt

brackets till screw tip securely contacts wall plate as

shown in cross section.

Removing Screen: To remove screen from mount,

loosen safety screws, swing screen away from mount,

and lift screen off of mount.

Mounting and Removing Flat Panel Screen

DETAIL 2

ﬁg. 4.1

IncreLok™

TILT LOCKING

SCREW LOCATOR

HOLE

RATCHET

HANDLE

TILT

POSITION

HOLES

ﬁg. 3.2

Adjusting the Tilt Angle of the Flat Panel

Screen

• Always use an assistant or mechanical lifting equipment

to safely lift and position the ﬂat panel screen.

• Do not tighten screws with excessive force.

Overtightening can cause damage to mount. Tighten

screws to 40 in. • lb (4.5 N.M.) maximum torque.

• Be careful not to pinch ﬁngers when pushing screen from

the bottom.

WARNING

ﬁg. 3.1

RATCHET

HANDLE

SAFETY/

SECURITY

SCREW

DETAIL 1

BB &

CROSS SECTION

BB &

All other brand and product names are trademarks or registered trademarks of their respective owners.

Peerless Industries, Inc.

3215 W. North Ave.

Melrose Park, IL 60160

www.peerlessmounts.com

Anbringung und Zusammenbau:

SmartMount®-Universal-Wandkipphalter für LCD- und Plasma-

Flachbildschirme

Merkmale:

• Angebrachter Bildschirm steht nur 76 mm (3 Zoll) von der Wand ab und fügt sich so unauffällig in den Raum

• Wandplattendesign ermöglicht Zugang zur Wand und bietet damit vielfältige Kabelführungsoptionen

• Schnelle Anbringung durch einfaches Einhaken der Universal-Kipphalterungen in die Wandplatte

• Optimaler Betrachtungswinkel durch Neigbarkeit bis 15° nach vorne und -5° nach hinten

• Mühelose Neigungseinstellung durch einmaliges Antippen

• Vorspannung der Universalkipphalterung ermöglicht Neigungswinkeleinstellung mit einer einfachen Bewegung

• Arretieren der Bildschirmstellung über leicht zugänglichen Griff

• Optionale IncreLok-Funktion bietet ﬁxe Neigungsstellungen bei -5°, 0°, 5°, 10° und 15°

• Einschließlich Sorted-For-You™-Befestigungsteilesortiment zur Anbringung an Holzständern, Beton und Porenbetonstein

• Optionale horizontale Verstellung bis zu 203 mm (8 Zoll) (abhängig vom Bildschirmmodell) ermöglicht optimale Platzierung des Bildschirms

• In Schwarz oder Silber verfügbar

HINWEIS: Lesen Sie bitte das gesamte Anleitungsblatt durch, bevor Sie mit Anbringung und Zusammenbau beginnen.

USC

Modell-Nr. Bildschirmgröße Max. Tragfähigkeit gem. UL-Zulassung

ST670, ST670P, ST670-S, ST670P-S,

SWS520/BK, SWS520/SI 42''- 71'' (107 - 180 cm) 250 lb (113 kg)

ST680, ST680P, ST680-S, ST680P-S 61''- 102'' (155 - 259 cm) 350 lb (159 kg)

AUSGEGEBEN: 03-25-09 BLATT NR.: 2029334-1

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere PEERLESS Mounts Rack & Stand Handbücher

PEERLESS Mounts

PEERLESS Mounts PLAV70-UNLP-GB Leitfaden

PEERLESS Mounts

PEERLESS Mounts DS-VL-H060 Leitfaden

PEERLESS Mounts

PEERLESS Mounts PLA 50-UNL Leitfaden

PEERLESS Mounts

PEERLESS Mounts RTLA-100 Leitfaden

PEERLESS Mounts

PEERLESS Mounts FPECMC-01 Leitfaden

PEERLESS Mounts

PEERLESS Mounts DS-VL-H048 Leitfaden

PEERLESS Mounts

PEERLESS Mounts SUT660P Leitfaden

PEERLESS Mounts

PEERLESS Mounts Smartmount D-FPF-220 Leitfaden

PEERLESS Mounts

PEERLESS Mounts ACC488 Leitfaden

PEERLESS Mounts

PEERLESS Mounts DS-VL-H072 Leitfaden

PEERLESS Mounts

PEERLESS Mounts LCT-A1B6C Leitfaden

PEERLESS Mounts

PEERLESS Mounts Paramount PF660 Leitfaden

PEERLESS Mounts

PEERLESS Mounts FPEWM Leitfaden

PEERLESS Mounts

PEERLESS Mounts PRG UNV Leitfaden

PEERLESS Mounts

PEERLESS Mounts SmartMount ST632P Leitfaden

PEERLESS Mounts

PEERLESS Mounts ACC328 Leitfaden

PEERLESS Mounts

PEERLESS Mounts LCT-A1B2H Leitfaden

PEERLESS Mounts

PEERLESS Mounts Solid-Point PLA 2 Leitfaden

PEERLESS Mounts

PEERLESS Mounts LCT-A1B3H Leitfaden

PEERLESS Mounts

PEERLESS Mounts LCT-A1B3C Leitfaden

PEERLESS Mounts

PEERLESS Mounts LCT-A1B1C Leitfaden

PEERLESS Mounts

PEERLESS Mounts PLAV 70-UNL Leitfaden

PEERLESS Mounts

PEERLESS Mounts Smartmount D-FPF-220 Leitfaden

PEERLESS Mounts

PEERLESS Mounts LCT-A1B4C Leitfaden

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung