PEERLESS PJF2-UNV Leitfaden

ISSUED: 01-14-09 SHEET #: 056-9018-3 11-10-16

Visit the Peerless Web Site at www.peerless-av.com

1 of 9

For customer care call 1-800-865-2112.

Installation and Assembly Manual:

Vector Pro II™

Models: PJF2-UNV, PJF2-UNV-S

Maximum UL Load Capacity: 50 lb (27 kg)



This product is intended for use with UL

Listed products and must be installed

by a qualied professional installer.

Compatible

model/series*

ENG AEC*,

EXT*,

ADD*,

ACC500*,

CMJ400*,

DCT100,

DCS200,

CMJ500R1.

ISSUED: 01-14-09 SHEET #: 056-9018-3 11-10-16

Visit the Peerless Web Site at www.peerless-av.com

2 of 9

For customer care call 1-800-865-2112.

Tools Needed for Assembly

• studnder("edgetoedge"studnderisrecommended)

• phillipsscrewdriver

• drill

• 1/4"masonrybitforconcretesurface

• 5/32"bitforwoodstuds

• level

• 3/8"(10mm)socketwrench

• Itistheresponsibilityoftheinstallertoensurethat

theprojectorisproperlyventilated.Feetofchannels

areusedtoraisethemountofftheprojectorsurface.

CAUTION

Note:Readentireinstructionsheetbeforeyoustartinstallationandassembly.

• DonotbegintoinstallyourPeerlessproductuntilyouhavereadandunderstoodtheinstructionsandwarningscon-

tainedinthisInstallationSheet.Ifyouhaveanyquestionsregardinganyoftheinstructionsorwarnings,callPeer-

lesscustomercareat1-800-865-2112.

• Thisproductshouldonlybeinstalledbysomeoneofgoodmechanicalaptitude,hasexperiencewithbasicbuilding

construction,andfullyunderstandstheseinstructions.

• Makesurethatthesupportingsurfacewillsafelysupportthecombinedloadoftheequipmentandallattachedhard-

wareandcomponents.

• NeverexceedtheMaximumULLoadCapacity.

• Alwaysuseanassistantormechanicalliftingequipmenttosafelyliftandpositionequipment.

• Tightenscrewsrmly,butdonotovertighten.Overtighteningcandamagetheitems,greatlyreducingtheirholding

power.Seesuggestedtorquevalueswhereapplicablewithintheseinstructions.

WARNING

Table of Contents

PartsList............................................................................................................................................................................3

InstallationtoWoodJoistorWoodBeamCeilings............................................................................................................ 4

InstallationtoConcreteCeilings........................................................................................................................................ 5

FlushMountApplication .................................................................................................................................................... 6

InstallationtoExtensionColumns ..................................................................................................................................... 7

AttachingAdapterPlatetoProjector.................................................................................................................................. 8

AttachingAdapterPlatetoProjectorMount,ProjectorAlignment ..................................................................................... 9

ISSUED: 01-14-09 SHEET #: 056-9018-3 11-10-16

Visit the Peerless Web Site at www.peerless-av.com

3 of 9

For customer care call 1-800-865-2112.

Beforeyoustartcheckthepartslisttoinsureallofthepartsshownareincluded.

ACD

Note: Actual parts may appear slightly different than illustrated.

E GF H J K L

Parts List PJF2-UNV

Part #

PJF2-UNV-S

Part #

Description Qty

Aballandsocketmount 1 055-0011 055-0016

Badapter plate 1 055-1867 055-4867

Cceilingplate 1 580-1042 580-4042

Dextensioncolumnconnector 1 580-1025 580-4025

EM5x.8x10mmsocketpintypeFscrew 1520-1164 520-2031

F#10-32x3/8"spadethumbscrew 1560-1107 560-2107

G#10-32x3/8"serratedwasherheadsocketpinscrew 1 520-1151 520-2151

H#14x2.5phillipshexheadwoodscrew 2 5S1-015-C03 5S1-015-C04

J.25"IDx.56"ODx.26spacer 2 590-1050 590-2071

K#10-32x3/8"socketpinscrew 2 520-1084 520-2084

L#10-32x3/16"slottedsetscrew 3 520-1187 520-2187

Mwasher 4 540-1025 540-2025

NM3x8mmserratedwasherheadsocketpinscrew 4 510-1004 510-2004

OM4x10mmserratedwasherheadsocketpinscrew 4510-1060 510-2060

PM5x10mmserratedwasherheadsocketpinscrew 4510-1126 510-2063

RM6x10mmserratedwasherheadsocketpinscrew 4510-1066 510-2066

T2mmsecurityallenwrench 1560-1097 560-1097

U4mmsecurityallenwrench 1560-9646 560-9646

VM5x20mmserratedwasherheadsocketpinscrew 4510-1065 510-2065

ISSUED: 01-14-09 SHEET #: 056-9018-3 11-10-16

Visit the Peerless Web Site at www.peerless-av.com

4 of 9

For customer care call 1-800-865-2112.

WOODJOIST

Drilltwo5/32"(4mm)dia.holestoaminimum

depthof2.5"(64mm).Attachceilingplate(C)

withtwo#14x2.5"(6mmx65mm)wood

screws(H)asshownusing3/8"(10mm)socket

wrench.

Skip to step 3 for ush mount installation.

Skip to step 4 for extension column

installation.

For Optional Cord Management,

installtwospacers(J)betweenceiling

plate(C)andceiling.

Installation To Wood Joist Finished Ceilings,

Exposed Wood Joists, or Wood Beam Ceilings

WOODJOIST

CEILING

• Itistheresponsibilityoftheinstallertoverifythatthe

supportingsurfacewillsafelysupportthecombined

loadofallattachedhardwareandcomponents.

WARNING

IMPORTANT: Be sure to drill holes into the

joist CENTER!

CEILING

• WheninstallingPeerlessceilingmountsonawoodjoist/beamcoveredwithgypsumboard(drywall),verifythatthe

joistsorbeamsareaminimumof2"x4"nominalsize.Donotinstallovergypsumboardthickerthan5/8".

• Tightenwoodscrews(H)sothatceilingplate(C)isrmlyattached,butdonotovertighten.Overtighteningcandam-

agethescrews,greatlyreducingtheirholdingpower.

• Nevertighteninexcessof80in•lb(9N.M.).

• Makesurethatmountingscrewsareanchoredintothecenterofthestuds.Theuseofan"edgetoedge"studnder

ishighlyrecommended.

WARNING

ISSUED: 01-14-09 SHEET #: 056-9018-3 11-10-16

Visit the Peerless Web Site at www.peerless-av.com

5 of 9

For customer care call 1-800-865-2112.

CONCRETECEILING

Drilltwo1/4"(6mm)dia.holestoaminimumdepthof

2.5"(64mm).Attachceilingplate(C)usingtwoconcrete

anchorsand#14x2.5"woodscrews(H)asshownin

Illustration A and 1, 2,and3 (below).Tightenallfasteners.

IMPORTANT: It is the responsibility of the installer to

verify that the ceiling will safely support the combined

load of all attached hardware and components.

Skip to step 3 for ush mount installation.

Skip to step 4 for extension column installation.

Illustration A

Installation to Concrete Ceilings

Use only PEERLESS ACC233 concrete anchors (sold separately).

• FOR DIRECT ATTACHMENT TO LOAD BEARING

CONCRETE ONLY! Concreteexpansionanchorsare

not intendedforattachmenttoconcreteceilingscov-

eredwithalayerofplaster,drywall,orothernishing

material.

WARNING

• Tightenwoodscrewssothatceilingplateisrmly

attached,butdonotovertighten.Overtighteningcan

damagethescrews,greatlyreducingtheirholding

power.

• Nevertighteninexcessof80in•lb(9N.M.).

• Makesurethatmountingscrewsareanchoredinto

thecenterofthestuds.Theuseofan"edgetoedge"

studnderishighlyrecommended.

WARNING

• WheninstallingPeerlessceilingmountsonaconcreteceiling,theceilingmustbeatleast8"thickwithaminimum

compressivestrengthof2000psi.

• Makesurethatthesupportingsurfacewillsafelysupportthecombinedloadoftheequipmentandallattachedhard-

wareandcomponents.

• NeverexceedtheMaximumLoadCapacityof50lb(27kg).

WARNING

CONCRETECEILING

concrete

anchor

Drillholesandinsertanchors(H).

Placeplate(B)overanchors(H)andsecurewithscrews(E).

Tightenallfasteners.

concrete

surface

ISSUED: 01-14-09 SHEET #: 056-9018-3 11-10-16

Visit the Peerless Web Site at www.peerless-av.com

6 of 9

For customer care call 1-800-865-2112.

Screwballandsocketmount(A)intoceilingplate(C)asshowningure 3.1 (minimum5turns).Alignthenotch

withoneofthefourholesoftheceilingplate(C)andsecureballandsocketmount(A)withaM5x10mmsocket

pinscrew(E)usingsecurityallenwrench(U)asshowningure 3.2

NOTE: Slottedsetscrew(L)isusedtojamagainstthethreadsoftheballandsocketmounttopreventanyexcess

movementoftheballandsocketmount(A).Donotovertightenscrew;overtighteningscrewwilldamagethreads

makingitdifculttoseparatetheproducts.

Skip to step 5.

Flush Mount Application

WOODJOIST

CEILING

NOTCH

gure 3.1

gure 3.2

ISSUED: 01-14-09 SHEET #: 056-9018-3 11-10-16

Visit the Peerless Web Site at www.peerless-av.com

7 of 9

For customer care call 1-800-865-2112.

Screwextensioncolumntoceilingplate(C).

Alignthenotchwithoneofthefourholesin

theceilingplate(C)andsecureextension

columnwithaM5x10mmsocketpinscrew

(E)usingsecurityallenwrench(U).See

gure 4.1

Screwextensioncolumnconnector(D)to

extensioncolumn.Alignslotinextension

columnwithoneofthetopholesin

extensioncolumnconnector(D).Insertand

tightenone#10-32x3/8"socketpinscrew

(K)throughextensioncolumnconnector(D)

intoslotonextensioncolumnusingsecurity

allenwrench(U).See gure 4.2

Screwballandsocketmount(A)to

extensioncolumnconnector(D).Alignslot

inballandsocketmount(A)tooneofthe

bottomholesinextensioncolumnconnector

(D).Insertandtightenone#10-32x3/8"

socketpinscrew(K)throughextension

columnconnector intoslotinballandsocket

mount(A)usingsecurityallenwrench(U).

See gure 4.3

Allpipethreadconnectionsbetweentheball

andsocketmount(A),columnconnector

(D),ceilingplate(C)mustbethreadeda

minimumof5turns.

Slottedsetscrews(L)areusedtojam

againstthethreadsofeachconnectingjoint

topreventanyexcessmovement.Donot

overtightenscrews;overtighteningscrews

willdamagethreadsmakingitdifcultto

separatetheproducts.

SLOT

gure 4.1

gure 4.3

gure 4.2

EXTENSION

COLUMN

Installation to

Extension Column

EXTENSION

COLUMN

SLOT

EXTENSION

COLUMN

SLOT

ULlistedPeerlessmodel

EXT, AEC, or ADD series

extensioncolumn(sold

separately).

ISSUED: 01-14-09 SHEET #: 056-9018-3 11-10-16

Visit the Peerless Web Site at www.peerless-av.com

8 of 9

For customer care call 1-800-865-2112.

MOUNTINGHOLE

GENERICPROJECTOR

Placeprojectorupsidedown.Locateadapterplate(B)withnotchfacingforwardasclosetoprojectorcenterof

gravityaspossiblewithoutcoveringanymountingholes.Loosenchannels,andifthereareonlythreemount-

ingholesremovefourthchannel.Usingonechannelforeachmountinghole,positionfeetofchannelsover

mountingholesasshownbelow.IMPORTANT:Ifprojectordoesnothaveatleastthreemountingholes,donot

use this adapter plate.

NOTE:Someprojectorshavefeetwhichcanberemovedandthecorrespondingthreadedinsertcanbeused

foramountinghole.

NOTE:Oncechannelsareinpositionretightenfasteners.

NOTE:Theprojectoryouareinstallingmaydifferinappearancefromthesampleillustratedbelow.

Attachadapterplate(B)toprojectorusingonescrew(N, O, P, R, or V)foreachchannelasshownbelow.

Tightenallscrews,whilekeepingthecenterofgravity.Besurethatadapterplate(B)isstraight.Adjustthefeet

ofthechannelstokeeptheadapterplatelevel.Tightenallscrewswith4mmsecurityallenwrench(U)orwrench

providedwithprojectormount,whilekeepingthecenterofgravity.IfM3screwsareused,tightenusing2mm

securityallenwrench(T).

NOTE:Projectorswillrequiredifferentsizescrewsformounting.Useacombinationofscrews(N, O, P, R, or V)

andfootadjustmentthatwillresultinchannelsofadapterplate(B)ttingtightlyagainstprojector.IMPORTANT:

Inordertoproperlyengagethethreadsinthemountingholes,thescrewmustbeturnedatleast3fullturns.

Note:Ifusingscrew(N),placewasher(M)betweenscrew(N)andfootofchannel.

FOOTOFCHANNEL

• Itistheresponsibilityoftheinstallertoensurethat

theprojectorisproperlyventilated.Feetofchannels

areusedtoraisethemountofftheprojectorsurface.

CAUTION N, O, P, R, or V

Attaching Adapter Plate to Projector

NOTCHINDICATES

FRONTOFPROJECTOR

ISSUED: 01-14-09 SHEET #: 056-9018-3 11-10-16

Visit the Peerless Web Site at www.peerless-av.com

9 of 9

For customer care call 1-800-865-2112.

Toadjustroll,pitch,andyawloosenthesetscrew

(shownbelow)usingsecurityallenwrench(U)or

standard4mmallenwrench.Youshouldbeabletojust

slightlyloosenthescrewsothatyouradjustmentscan

besetwithouthavingtoholdtheprojector.Moveprojec-

tortodesiredpositionandslowlytightensetscrew.

NOTE: Be sure not to touch the projector while tight-

ening the set screw. This may cause the image to be

unaligned when you let go.

IMPORTANT: Allen wrench is your key for projector

removal. Store it in a safe place.

Attachprojector,withadapterplate(B)alreadyonit,to

theballandsocketmount(A)byinsertingtheballand

socketmountintotheadapterplateconnectionand

twistinguntiltheadapterplatewillnolongerturn(about

75°).Thespringloadedcaptivescrewshouldlineup

withacorrespondingholeontheadapterplate(this

shouldlineupautomaticallywhenthetwoareconnect-

ed).Pushdownandtightenthespringloadedcaptive

screwtosecuretheadapterplatetothemount.Ifnot

usingtheoptionalsecurityfeature,fastenthumbscrew

(F)intheholeoppositethespringloadedcaptivescrew.

OPTIONAL:ForArmorLock™security,insertserrated

washerheadsocketpinsecurityscrew(G)inthehole

oppositethespringloadedcaptivescrew.Tightenwith

securityallenwrench(U).Thiswillpreventtheprojector

frombeingremoved.

NOTE: Be sure to only use the #10-32 x 3/8"

screw (G) (or the thumb screw (F)) opposite the

spring loaded captive screw.

WOOD

JOIST

CEILING

PROJECTOR

ADAPTERPLATE

PROJECTOR

WOODJOIST

CEILING

PROJECTOR

CUTAWAYVIEWOF

CEILINGPLATE(C)

• Donotliftmoreweightthanyoucanhandle!Usead-

ditionalmanpowerormechanicalliftingequipmentto

safelyhandleplacementoftheprojector!

WARNING

7 8

Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.

Attaching Adapter Plate to Projector Mount

SETSCREW

CAPTIVE

SCREW

Andere Handbücher für PJF2-UNV

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere PEERLESS Rack & Stand Handbücher

PEERLESS

PEERLESS Solid-Point PLCM UN1 Leitfaden

PEERLESS

PEERLESS WSP820 Leitfaden

PEERLESS

PEERLESS Smartmount ST670 Leitfaden

PEERLESS

PEERLESS CMJ450 Leitfaden

PEERLESS

PEERLESS IMC 18 Leitfaden

PEERLESS

PEERLESS SAL730P Leitfaden

PEERLESS

PEERLESS IM760P Leitfaden

PEERLESS

PEERLESS PLA 50-UNL Leitfaden

PEERLESS

PEERLESS COL 510P Leitfaden

PEERLESS

PEERLESS ESA746PU Leitfaden

PEERLESS

PEERLESS HCACC503 Bedienungsanleitung

PEERLESS

PEERLESS Smartmount Leitfaden

PEERLESS

PEERLESS RTPLA 50 Leitfaden

PEERLESS

PEERLESS Smartmount SWS310/BK Leitfaden

PEERLESS

PEERLESS IWB600-WB Leitfaden

PEERLESS

PEERLESS SmartMount SA770PU Leitfaden

PEERLESS

PEERLESS PARAMOUNT PF640 Leitfaden

PEERLESS

PEERLESS MIS488 Leitfaden

PEERLESS

PEERLESS PRG-1 Leitfaden

PEERLESS

PEERLESS SmartMount D-FPF-320 Leitfaden

PEERLESS

PEERLESS SOLID POINT PLCM 1 Bedienungsanleitung

PEERLESS

PEERLESS ACC 604 Leitfaden

PEERLESS

PEERLESS SGLS01 Leitfaden

PEERLESS

PEERLESS WBK100-W Leitfaden

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung