PEERLESS ESA746PU Leitfaden

Installation and Assembly:

Corrosion Resistant Articulating Mount for Indoor or Outdoor

26" to 46" Flat Panel Displays

Models: ESA746PU, ESA746PU-S

ISSUED: 01-15-11 SHEET #: 061-9061-2 02-01-11

3215 W. North Ave. • Melrose Park, IL • (800) 865-2112 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com

Max UL Load Capacity: 80 lb (36.3 kg)

USC

2 of 35 ISSUED: 01-15-11 SHEET #: 061-9061-2 02-01-11

• Do not begin to install your Peerless product until you have read and understood the instructions and warnings

contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US

customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact

your local distributor.

• This product should only be installed by someone of good mechanical aptitude, has experience with basic building

construction, and fully understands these instructions.

• Due to outdoor environmental conditions such as heavy snow, hail, rain, etc. the environmental mount and

hardware must be inspected at least once a year. This product should not be exposed to high winds. A qualiﬁed

installer or inspector must check for signs of rust, loose fasteners, bent metal, etc. If evidence of excessive wear,

deterioration or any unsafe condition is observed, this product must be taken out of service immediately. Direct all

inquiries to customer care if you have any questions.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardware and components.

• Never exceed the Maximum UL Load Capacity. See page one.

• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of

an "edge to edge" stud ﬁnder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tighten screws ﬁrmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding

power.

• This product was designed to be installed on the following wall construction only;

WALL CONSTRUCTION HARDWARE REQUIRED

• Wood Stud Included

•Wood Beam Included

•Solid Concrete Included

•Cinder Block Included

•Metal Stud Contact Qualiﬁed Professional (not evaluated by UL)

•Brick Contact Qualiﬁed Professional (not evaluated by UL)

•Other or unsure? Contact Qualiﬁed Professional

WARNING

Note: Read entire instruction sheet before you start installation and assembly.

Table of Contents

Parts List.................................................................................................................................................................................3

Installation to Wood Stud Wall................................................................................................................................................5

Installation to Solid Concrete and Cinder Block .....................................................................................................................6

Tools Needed for Assembly

• stud ﬁnder ("edge to edge" stud ﬁnder is recommended)

• phillips screwdriver

• drill

• 3/16" (5mm) for wood studs, 13/32" (10mm) for concrete and cinder block

• level

3 of 35 ISSUED: 01-15-11 SHEET #: 061-9061-2 02-01-11

Parts may appear slightly different than illustrated.

Before you begin, make sure all parts shown are included with your product.

Parts List ESA746PU ESA746PU-S

Description Qty. Part # Part #

wall arm 1 095-T1971 095-7971

Bwall plate 1 024-T1050 024-7050

Cadapter brackets 2 095-T1945 095-7945

D2.5" wood screws 3 520-D1033 520-D1033

Econcrete anchors 4 590-0320 590-0320

Fcable ties 8 560-1756 560-1756

Gcable tie anchors 2 590-1290 590-1290

H8-32 x 1/4" phillips screw 2 520-D1622 520-D1622

Iplastic cord covers 2 590-P1323 590-P1323

K#10-32 x 1/4" flat head phillips screw 1 520-D1108 520-D1108

L5 mm allen wrench 2 560-9640 560-9640

M#3 screwdriver bit 1 560-0209 560-0209

N2-1/2" security wood screw 1 520-D1668 520-D1668

O4mm security allen wrench 1 560-9646 560-9646

P1/4-20 x 1/2" socket pin screw

2 520-D1069 520-D1069

4 of 35 ISSUED: 01-15-11 SHEET #: 061-9061-2 02-01-11

Adapter Bracket Fasteners

M4 x 12 mm (6)

(510-D1079)

M4 x 25 mm (4)

(510-D1082)

M5 x 12 mm (4)

(520-D1064) M5 x 25 mm (4)

(520-D1122)

M8 x 12 mm (6)

(520-D1068)

M8 x 40 mm (4)

(520-D1152)

M8 x 25 mm (4)

(520-D1101)

I.D. .34" (4)

(540-1059)

I.D. .22" (4)

(540-1057)

M6 x 30 mm (4)

(520-D1067)

M6 x 12 mm (4)

(520-D1050)

M6 x 25 mm (4)

(520-D1211)

M6 x 20 mm (4)

(520-D1554)

multi-washer (6)

(580-D1036)

5 of 35 ISSUED: 01-15-11 SHEET #: 061-9061-2 02-01-11

3.95"

(100mm)

CS = Center of Screen

ﬁg. 1.1

ﬁg. 1.2

ﬁg. 1.3

Installation to Wood Stud Wall

Use a stud ﬁnder to locate the edges of the studs and draw a vertical line down the center of each stud.

Use wall

plate (B) as a template to mark center of four mounting holes. The top mounting slots should be located 3.95"

(100mm) above the desired screen center as shown in ﬁgure 1.1.

Drill four

5/32" (4mm) dia. holes to a depth

of 2-1/2" (64mm)

. Attach wall plate (B) to wall using three wood screws (D) and one security wood screw (N) as

shown in ﬁg. 1.2. Level wall plate then tighten all fasteners.

Attach wall arm (A) to wall plate (B) with two 1/4-20 x 1/2" socket pin screws (P) as shown in ﬁgure 1.3.

• Installer must verify that the supporting surface will safely support the combined load of the equipment and all

attached hardware and components.

• Tighten wood screws so that wall plate is ﬁrmly attached, but do not overtighten. Overtightening can damage the

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud ﬁnder

is highly recommended.

• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs.

Installers are responsible to provide hardware for other types of mounting situations (not evaluated by UL).

WARNING

STUD

6 of 35 ISSUED: 01-15-11 SHEET #: 061-9061-2 02-01-11

Installation to Solid Concrete and Cinder Block

• When installing Peerless wall arms on cinder block, verify that you have a minimum of 1-3/8" (35 mm) of actual

concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount

in a solid part of the block, generally 1" (25 mm) minimum from the side of the block. Cinder block must meet ASTM

C-90 speciﬁcations. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a

hammer drill to avoid breaking out the back of the hole when entering a void or cavity.

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardware and components.

WARNING

• Tighten screws so that wall plate is ﬁrmly attached,

but do not overtighten. Overtightening can damage

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Always attach concrete expansion anchors directly

to load-bearing concrete.

• Never attach concrete expansion anchors to

concrete covered with plaster, drywall, or other

ﬁnishing material. If mounting to concrete surfaces

covered with a ﬁnishing surface is unavoidable (not

evaluated by UL), the ﬁnishing surface must be

counterbored as shown below. Be sure concrete

anchors do not pull away from concrete when

tightening screws. If plaster/drywall is thicker than

5/8" (16 mm), custom fasteners must be supplied by

installer (not evaluated by UL).

WARNING

SOLID CONCRETE

CINDER BLOCK

Use wall plate (B) as a template to mark center of

holes.

The top mounting slots should be located

3.95" (100mm) above the desired screen center

as shown in ﬁgure 1.1 on page 5.

Drill four 5/16"

(8mm) dia. holes to a minimum depth of 2.5"

(64mm). Insert anchors (E) into holes. Attach wall

plate to wall using three wood screws (D) and one

security wood screw (N) as shown in ﬁg. 1.4. Level

wall plate then tighten all fasteners.

Attach wall arm (A) to wall plate (B) with two

1/4-20 x 1/2" socket pin screws (P) as shown in

ﬁgure 1.3 on page 5.

ﬁg. 1.4

CUTAWAY VIEW

INCORRECT CORRECT

wall

plate

wall

plate

plaster/

drywall

plaster/

drywall

concrete concrete

Drill holes and insert anchors (E).

Place plate (B) over anchors (E) and secure with screws (D,N).

Tighten all fasteners.

D,N

concrete

surface

7 of 35 ISSUED: 01-15-11 SHEET #: 061-9061-2 02-01-11

Installing Adapter Brackets

To prevent scratching the screen, set a cloth on a ﬂat, level surface that will support the weight of the screen. Place

screen face side down. If screen has knobs on the back, remove them to allow the adapter brackets to be attached.

Place adapter brackets (C) on back of screen, align to holes, and center on back of screen as shown below. Attach

the adapter brackets to the back of the screen using the appropriate combination of screws, washers, and spacers

as shown in steps 2-1 or 2-2.

NOTE: Top and bottom holes must always be used.

Verify that all holes are properly aligned, and then tighten screws using a phillips screwdriver.

NOTE: For ﬂat back screens proceed to step 2-1. For bump-out or recessed back screen skip to step 2-2.

CENTER BRACKETS

VERTICALLY

ON BACK OF SCREEN

NOTE: "X" dimensions should be equal.

• Tighten screws so adapter brackets are ﬁrmly attached. Do not tighten with excessive force. Overtightening can

cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become

detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.

• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly

secured, damage may occur to screen or product may fail.

WARNING

8 of 35 ISSUED: 01-15-11 SHEET #: 061-9061-2 02-01-11

Begin with the shortest length screw, hand thread through washer and adapter bracket into screen as shown

below. Screw must make at least three full turns into the mounting hole and ﬁt snug into place. Do not over

tighten. If screw cannot make three full turns into the screen, select a longer length screw from the bafﬂed

fastener pack. Repeat for remaining mounting holes, level brackets and tighten screws.

NOTE: Spacers may not be used, depending upon the type of screen.

Begin with longer length screw, hand thread through washer, adapter bracket and spacer in that order into screen

as shown below. Screw must make at least three full turns into the mounting hole and ﬁt snug into place. Do not

over tighten. If screw cannot make three full turns into the screen, select a longer length screw from the bafﬂed

fastener pack. Repeat for remaining mounting holes, level brackets and tighten screws.

For Flat Back Screen

For Bump-out or Recessed Back Screen

ADAPTER BRACKET (C)

SCREEN

WASHER

SCREW

2-2

2-1

If you have any questions, please call Peerless customer care at 1-800-865-2112.

SCREEN

WASHER

SCREW

ADAPTER BRACKET (C)

SPACER

9 of 35 ISSUED: 01-15-11 SHEET #: 061-9061-2 02-01-11

ﬁg 3.1

TENSION KNOB

ROLL

BRACKET

ﬁg. 4.1

ﬁg. 4.2

SAFETY

SCREWS

CROSS

SECTION

Mounting and Removing Flat Panel Screen

Hook adapter brackets (C) onto center of adapter

plate (A). NOTE: Adapter brackets (C) must be

centered on adapter plate (A) or product may not

function properly. Turn security screws, using a

phillips screwdriver, clockwise at least six times to

prevent screen from being removed as shown in

cross section of ﬁg. 3.1.

NOTE: To lock the screen down, tighten security

screws to wall plate as shown in cross section.

To remove screen from mount, loosen security

screws, swing screen away from mount, and lift

screen off of mount.

• Always use an assistant or mechanical lifting equipment to safely lift and position the ﬂat panel screens.

WARNING

• Do not tighten screws with excessive force.

Overtightening can cause damage to mount. Tighten

screws to 40 in. • lb (4.5 N.M.) maximum torque.

CAUTION

Hold screen securely and loosen tension knob on

side of mount shown in ﬁgure 4.1 to allow for tilt.

Adjust screen to desired tilt (15° forward, 5°

backward), then retighten tension knob.

Rotate screen by hand to level screen. Roll bracket

allows 2° roll adjustment.

Insert #10-32 x 1/4" ﬂat head phillips screw (K) to

lock screen into position as shown in ﬁgure 4.2.

• Be careful not to pinch ﬁngers when opening and

closing mount from the wall.

• Do not tighten screws with excessive force.

Overtightening can cause damage to mount. Tighten

screws to 40 in. • lb (4.5 N.M.) maximum torque.

CAUTION

4-1

10 of 35 ISSUED: 01-15-11 SHEET #: 061-9061-2 02-01-11

DETAIL 1

CORD

ﬁg. 5.1

ﬁg. 5.2

ﬁg. 5.3

CORD

Attach cable tie anchor (G) to top or bottom of wall arm (A) using 8/32 x 1/4" phillips screw (H) as shown in ﬁgure

5.1. Secure cables to top or bottom of wall arm (A) using cable ties (F) as shown in ﬁgure 5.2.

Route cords inside arm slots of wall arm (A). Lock cords into place by snapping cord covers (I) onto mount as

shown in ﬁgure 5.3. NOTE: Be sure arrow on inside of cable covers (I) points toward screen as shown in detail 1.

Cables may also be secured to slot at bottom of wall plate using a cable tie (F) as shown.

Cable Management

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere PEERLESS Rack & Stand Handbücher

PEERLESS

PEERLESS DST940 Leitfaden

PEERLESS

PEERLESS PARAMOUNT PRA2X2 Bedienungsanleitung

PEERLESS

PEERLESS RTPLA 50 Leitfaden

PEERLESS

PEERLESS ACC-V800X Leitfaden

PEERLESS

PEERLESS IM760P Leitfaden

PEERLESS

PEERLESS Vision-Point LCV 100 Leitfaden

PEERLESS

PEERLESS FPZ-600 Leitfaden

PEERLESS

PEERLESS MSA-301 Leitfaden

PEERLESS

PEERLESS WSP 716 Bedienungsanleitung

PEERLESS

PEERLESS PJF2-UNV Leitfaden

PEERLESS

PEERLESS Slimline OP-LWB 530 Leitfaden

PEERLESS

PEERLESS SGLS01 Leitfaden

PEERLESS

PEERLESS Solid-Point PLCM UN1 Leitfaden

PEERLESS

PEERLESS SmartMount D-FPF-320 Leitfaden

PEERLESS

PEERLESS Paramount PA760 Leitfaden

PEERLESS

PEERLESS PLA 60-UNL Leitfaden

PEERLESS

PEERLESS IM740P Leitfaden

PEERLESS

PEERLESS DST360 Leitfaden

PEERLESS

PEERLESS CMJ450 Leitfaden

PEERLESS

PEERLESS PRS-KIT0811 Leitfaden

PEERLESS

PEERLESS WWSP 420 Bedienungsanleitung

PEERLESS

PEERLESS HCACC503 Bedienungsanleitung

PEERLESS

PEERLESS DS246 Leitfaden

PEERLESS

PEERLESS PARAMOUNT PP740 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung