RMS-D / RMS-D-RC / RMS-D-NA / RMS-D-RC-NA English
General Information for Your Safety
This device must be installed and maintained only by qualied, trained personnel.
Observe the safety requirements of EN 60950-1. Operate the sensor only with an SELV supply with a limited
output of up to 100 W. Use a T2.5 A fuse, for example, to reliably limit the power output.
Brief Instructions: Radar Motion Sensor for Detecting Persons at Automatic Doors
Scope of Delivery
Quantity Designation
1 Sensor RMS-D...
1 Connection cable with plug
1 Self-adhesive drilling template
2 Screws for mounting
1 Mounting instructions
Operating Elements
LED (red/green)
IR receiver
IR transmitter
DIP switches
Potentiometer
Connecting plug
Antenna
Product Information
Connecting the Radar
Connect the cable with the connecting plug:
Opening the Device
Open the housing from below:
Insert the screwdriver into the opening provided
and carefully push open the cover.
Fold up and remove the cover.
Mounting the Device
1. Attach the self-adhesive template
and drill according to the markings on the
template.
2. Pull the cable through the opening provided.
3. Fasten the base plate using the screws
(screws are in the housing).
Installation
Installation Information
• Protect the radar from rain*.
• Avoid placing moving objects in the detection
eld (fans, plants, trees, ags).
• Do not cover the radar. Only install the radar be-
hind appropriate covers. Mechanically operated
drive components may aect the radar.
• Avoid uorescent lights in the detection eld.
* Installation of the RMS Weather Cap is
recommended (see accessories).
Closing the Device
Attach the cover on the top and press down until it
snaps into place.
Turning the Antenna
to change the antenna characteristics
1. Select the shape of the detection area
(narrow or wide).
2. Remove the antenna carefully using two
ngers.
3. Turn the antenna through 90° and re-attach.
Do not touch any electronic components.
Do not use any metallic tools.
!
Technical Data
Functional principle Microwave module
Detection speed Min. 0.1 m/s
Marking CE
Inclination angle Vertical: 0° – 90° in 10° steps
Horizontal: -30° – +30° in 5° steps
Detection range at installation height
of 2200 mm and 30° inclination angle
Narrow (standard): 2000 x 4500 mm (WxD)
Wide: 4500 x 2000 mm (WxD)
Operating frequency 24.15 GHz – 24.25 GHz K band
NA version (FCC/IC): 24.075 GHz – 24.175 GHz K band
Operating mode Radar motion sensor
Function indicator Red/green LED
Operating elements DIP switch for selecting the mode of operation:
Direction detection, cross-trac suppression,
slow motion, switching mode, size of detection area,
adjuster for fall time
Operating voltage 12 – 36 VDC/12 – 28 VAC
No-load current < 50 mA at 24 VDC
Power consumption < 1.2 W at 24 V DC / < 1.7 W at 36 V DC
Switching mode Active/passive
Signal output Relay, 1 NO contact/NC contact
Switching voltage Max. 48 VAC / 48 VDC
Switching current Max. 0.5 AAC/1 ADC
Switching power Max. 24 W/60 VA
Fall time 0.2 s – 5 s, adjustable
Ambient temperature -20° C to 60° C/253 – 333 K
Relative humidity Max. 90 % without condensation
Mounting height Max. 4000 mm
Degree of protection IP 54
Connection 5 m connection cable with plug, 4-pin
(cable is included in the scope of delivery)
Housing material Polycarbonate (PC), ABS
Mass 130 g
Transmitting power (EIRP) < 20 dBm
Dimensions excluding securing parts 123 mm (w) x 65 mm (h) x 57 mm (d)
Troubleshooting
Fault Corrective action
Door is detected. Decrease the size of the detection area.
Change inclination angle.
LED not lit up. No power supply, device not functioning.
Sensor reacts to the slightest inuences
such as rain, vibrations, or reections.
Door opens for no apparent reason.
Increase immunity,
decrease the size of the detection area.
Potentiometer does not respond Operation with remote control is switched on.
Set DIP switch 6 to the UP position.
Remote control does not respond Operation with the DIP switch and potentiometer
is switched on. Set DIP switch 6 to the DOWN
position.
Device is locked. Switch the operating voltage
o and on again. The sensor can now be cong-
ured without a code for 30 minutes.
Check the remote control battery.
Factory Settings
Function Setting
DIP switches Switch 1 – 5: up
Switch 6: down
Detection area size Potentiometer:
Center position
Remote control: 9
Inclination angle 15°
Direction detection Forward
Fall time 1 s
Relay contact Active
Cross-trac
suppression
Potentiometer: o
Remote control: 1
Immunity 1
Slow motion O
Accessories
RMS
Remote Control
Remote control
RMS Weather Cap Mounting set and weather
protective cover
Conformity with Standards
EU conformity: Pepperl+Fuchs GmbH hereby
declares that the radio system types RMS-D
and RMS-D-RC comply with Directive 2014/53/
EU.
The full declaration of conformity is available at
www.pepperl-fuchs.com.
US conformity: The products RMS-D-NA and
RMS-D-RC-NA are compliant with Part 15 of the
FCC regulations.
Canada conformity: The products RMS-D-NA
and RMS-D-RC-NA contain an IC-approved
component.
IMPORTANT! The EU-compliant devices must
not be marketed in the United States/Canada
and the US/Canada-compliant devices must not
be marketed in Europe!
1 2
OPEN
3 4 5 6
1 7
456
23
Mounting options
Important: Do not open the housing from the top.
