Pepperl+Fuchs ICE1-8IOL-G60L-V1D Bedienungsanleitung

ICE1-8IOL-G60L-V1D,

ICE1-8IOL-G30L-V1D

Fieldbus Module with

Multiproto ol Te hnology

and I/O-Link

FACTORY AUTOMATION

MANUAL

With regard to the supply of products, the current issue of the following document is ap-

plicable: The General Terms of Delivery for Products and Services of the lectrical Indus-

try, published by the Central Association of the lectrical Industry (Zentralverband

lektrotechnik und lektroindustrie (ZV I) e.V.) in its most recent version as well as the

supplementary clause: " xpanded reservation of proprietorship"

IC 1-8IOL-G60L-V1D, IC 1-8IOL-G30L-V1D

1 Introdu tion................................................................................. 5

1.1 Content of this Do ument ................................................................... 5

1.2 Manufa turer ........................................................................................ 5

1.3 Target Group, Personnel...................................................................... 5

1.4 Symbols Used ...................................................................................... 5

2 Produ t Des ription ................................................................... 7

2.1 Use and Appli ation ............................................................................ 7

2.2 Displays and Operating Elements...................................................... 9

2.3 Interfa es and Conne tions.............................................................. 11

2.4 Dimensions......................................................................................... 15

3 Installation................................................................................. 16

3.1 General Information........................................................................... 16

4 Commissioning, Proto ol Setting ........................................... 17

4.1 Setting Proto ols ............................................................................... 17

5 Commissioning for EtherNet/IP .............................................. 19

5.1 Preparation ......................................................................................... 19

5.2 Configuration Example...................................................................... 20

5.3 IO-Link Master Parameters ............................................................... 23

5.4 Conne tions and Assembly Obje t.................................................. 33

5.5 Bit Assignment................................................................................... 36

5.5.1 Status Data of the IO-Link Master (Inputs) ....................................... 36

5.5.2 IO-Link Device Input Data ................................................................ 39

5.5.3 IO-Link Input & xtended IO-Link Status Data ................................. 41

5.5.4 IO-Link Input Data & xtended IO-Link Status Data

& IO-Link vent Data........................................................................ 44

5.5.5 Control Data of the IO-Link Master (Outputs)................................... 49

5.5.6 Control Data of the IO-Link Device (Outputs)................................... 50

5.6 EtherNet/IP Obje ts ........................................................................... 51

IC 1-8IOL-G60L-V1D, IC 1-8IOL-G30L-V1D

6 Commissioning for PROFINET................................................ 55

6.1 Preparation..........................................................................................55

6.2 Configuration Example ......................................................................55

6.2.1 Integration of PROFIN T IO Modules in the TIA Portal..................... 56

6.2.2 Assigning a Unique Device Name in the Control System ................. 58

6.2.3 Assigning the Device Name to a PROFIN T IO Module .................. 59

6.2.4 Configuring the IO-Link Channels ....................................................62

6.2.5 Parameterization of the IO-Link Channels ........................................ 66

6.2.6 Parameterization of the Status/Control Module ................................ 70

6.2.7 Siemens IO-Link Library................................................................... 74

6.2.8 Replacing Devices Without a Removable Medium/

Programming Unit ............................................................................75

6.2.9 Identification and Maintenance Functions (I&M)............................... 78

6.2.10 Prioritized Start-Up/Fast Start-Up (FSU)........................................... 81

6.2.11 Resetting Modules to their Factory Settings .....................................82

6.3 Bit Assignment ...................................................................................84

7 The Integrated Web Server...................................................... 89

8 Troubleshooting........................................................................ 95

8.1 Diagnosti s Indi ator in the Integrated Web Server.......................95

8.2 Alarm Signals and Error Messages from Modules via PROFINET 95

8.3 Alarm Signals and Error Messages via Ethernet IP........................97

IC 1-8IOL-G60L-V1D, IC 1-8IOL-G30L-V1D

Introduction

2019-02

1 Introduction

1.1 Content of this Document

This document contains information required to use the product in the relevant phases of the

product life cycle. This may include information on the following:

■

Product identification

■

Delivery, transport, and storage

■

Mounting and installation

■

Commissioning and operation

■

Maintenance and repair

■

Troubleshooting

■

Dismounting

■

Disposal

The documentation comprises the following parts:

■

This document

■

Datasheet

In addition, the documentation may comprise the following parts, if applicable:

■

U-type examination certificate

■

U declaration of conformity

■

Attestation of conformity

■

Certificates

■

Control drawings

■

Instruction manual

■

Other documents

1.2 Manufacturer

1.3 Target Group, Personnel

Responsibility for planning, assembly, commissioning, operation, maintenance, and

dismounting lies with the plant operator.

Only appropriately trained and qualified personnel may carry out mounting, installation,

commissioning, operation, maintenance, and dismounting of the product. The personnel must

have read and understood the instruction manual and the further documentation.

Prior to using the product make yourself familiar with it. Read the document carefully.

1.4 Symbols Used

This document contains symbols for the identification of warning messages and of informative

messages.

Note!

For full information on the product, refer to the further documentation on the Internet at

www.pepperl-fuchs.com.

Pepperl+Fuchs GmbH

Lilienthalstraße 200, 68307 Mannheim, Germany

Internet: www.pepperl-fuchs.com

2019-02

IC 1-8IOL-G60L-V1D, IC 1-8IOL-G30L-V1D

Introduction

Warning Messages

You will find warning messages, whenever dangers may arise from your actions. It is mandatory

that you observe these warning messages for your personal safety and in order to avoid

property damage.

Depending on the risk level, the warning messages are displayed in descending order as

follows:

Informative Symbols

Action

This symbol indicates a paragraph with instructions. You are prompted to perform an action or

a sequence of actions.

Danger!

This symbol indicates an imminent danger.

Non-observance will result in personal injury or death.

Warning!

This symbol indicates a possible fault or danger.

Non-observance may cause personal injury or serious property damage.

Caution!

This symbol indicates a possible fault.

Non-observance could interrupt the device and any connected systems and plants, or result in

their complete failure.

Note!

This symbol brings important information to your attention.

IC 1-8IOL-G60L-V1D, IC 1-8IOL-G30L-V1D

Product Description

2019-02

2 Product Description

2.1 Use and Application

The IC 1-8IOL-* modules function as an interface in an industrial fieldbus system. They enable

communication between a central controller at the control level and the decentralized sensors

and actuators at the field level. The resulting potential line or ring topologies that can be

achieved enable reliable data communication and a significant reduction in the amount of

wiring required, which therefore makes the costs for installation and maintenance reasonable.

Simple and quick extension is also possible.

The IC 1-8IOL-* series modules have a robust metal housing made of die-cast zinc. Due to the

fully encapsulated device housing, the module electronics are protected against environmental

influences and can be used in a wide range of temperatures. Despite the robust design, the

modules have compact dimensions and a low weight. They are especially suitable for use in

machines and plants with a moderate I/O concentration on distributed assemblies.

Multiproto ol (EtherNet/IP, PROFINET)

The multiprotocol modules allow you to select different protocols for communication within a

fieldbus system. As a result, multiprotocol modules can be integrated into different networks

without the need to purchase protocol-specific modules. Thanks to this technology, you can

also use one and the same module in different environments.

Using rotary coding switches in the lower area of the modules, you can comfortably and easily

set both the protocol and the address of the module, provided the protocol to be used supports

this. If you have chosen a protocol and started the cyclic communication once, the module

remembers this setting and uses the selected protocol from this point on. To use another

supported protocol with this module, perform a factory reset.

Input/Output Channels for the Field Level

For the field level, the modules have the following input/output channels

■

8 IO-Link master ports

• 4 IO-Link master ports Class A

• 4 IO-Link master ports Class B

If one or more of the IO-Link ports are not required, these can also be freely configured as

digital inputs or outputs (SIO mode).

■

4 hardwired digital inputs

■

4 configurable digital outputs (instead of the voltage outputs of Class B master ports on

pin 2)

IO-Link Chara teristi s of the Modules

The modules support IO-Link Standard V1.1.

■

Parametrization of IO-Link devices in PROFIN T using Siemens IO_LINK_D VIC

functional modules for Step 7 and the TIA Portal

8 x IO-Link master ports

■

4 Class A connections with an additional hard-wired digital input at pin 2 of the I/O port.

■

4 Class B connections with a galvanically isolated auxiliary power supply for up to 2 A per

port at pins 2 and 5 with a total current of 8 A.

■

The auxiliary power supply can optionally be configured as a digital output.

2019-02

IC 1-8IOL-G60L-V1D, IC 1-8IOL-G30L-V1D

Product Description

IO-Link connections

■

5-pin M12 connector

Parameter memory

■

The parameter storage function stores and monitors the parameters of the IO-Link device

and the IO-Link master.

■

The function makes it possible for you to easily replace the IO-Link device or the IO-Link

master.

This is possible from the IO-Link specification V1.1 and only if the IO-Link device and the

IO-Link master support the function.

IO-Link device parameterization

■

The IO-Link devices can be parameterized in the PROFIN T protocol using the Siemens

IO_LINK_D VIC functional module for ST P 7 and the TIA Portal.

Spe ial Produ t Features

■

Robust design:

Connectivity options for the module series include the widespread M12 connector with A

encoding for I/O signals and D coding for the network. In addition, the connectors are

color-coded to prevent confusion of the ports. The output circuits are galvanically isolated

from the rest of the network and the sensor electronics. Controllers are therefore reliably

protected against noise.

■

Integrated web server:

Network parameters such as IP address, subnet mask, and gateway can be adjusted via

the integrated web server. The modules support the communication protocols BOOTP

and DHCP for automated assignment of network parameters via the corresponding

servers.

You can read the parameters of the IO-Link device via the integrated web server and write

new parameters to the modules in single-write mode. Single-write mode does not activate

the automatic parameter storage mechanism.

■

For e Mode

In Force Mode, the module ports can be temporarily configured as digital inputs/outputs or

IO-Link ports. The configuration applies until the module is next switched off.

"Force Mode" allows the simulation of process data at the digital inputs/outputs without

the need to connect sensors and actuators. This means you can test an application in

advance without a full physical application. It is possible to simulate input switching states

or to switch outputs even without a controller. This feature eases and accelerates machine

commissioning and can be used to test new production plants.

■

Integrated network swit h:

The integrated two-port thernet switch of the modules allows you to set up a line

topology or a ring topology for the therNet/IP network or PROFIN T network. The

additionally implemented DLR or MRP protocol allows you to design a highly available

network infrastructure.

■

Redundan y fun tion:

The module firmware supports the redundancy function DLR (Device Level Ring) or MRP

(Media Redundancy Protocol) for ring topologies. This means that if the connection is

interrupted, the modules switch immediately to an alternative ring segment and thus

ensure interruption-free operation. The DLR class supported is "beacon-based" in

accordance with the therNet/IP specification.

■

Fail-safe fun tion:

The modules provide a fail-safe function. You can therefore choose the behavior of each

individual output channel in the event of an interruption or a loss of communication.

IC 1-8IOL-G60L-V1D, IC 1-8IOL-G30L-V1D

Product Description

2019-02

■

Qui kConne t:

QuickConnect allows the modules to record the communication in an therNet/IP network

particularly quickly through an accelerated boot-up process. This allows you to switch

tools faster, for example.

2.2 Displays and Operating lements

ICE1-8IOL-G30L-V1D

L D channel indicator

L D status indicator

Rotary switch

ICE1-8IOL-G30L-V1D

L D channel indicator

L D status indicator

Rotary switch

20X10X

X03

X4 X8

DIA

X04

BF DIA

Lnk/Act

X02

X01

UAux

DIA

x100 x10 x1

MS NS

0E/IP

X01

A B

Power

IO-Link

BF DIA

X02

X01 USUAux

X03

X02

X04

A B

Link/Act

E/IP

x100

x10

MS NS

2019-02

IC 1-8IOL-G60L-V1D, IC 1-8IOL-G30L-V1D

Product Description

Displays—General Part

Description for L D A, B, DIA, U

, U

Aux

Note!

The L Ds in the lower area of the thernet IO module have different names and functions

depending on the selected protocol. The following L D descriptions are therefore divided into

a general part (1), which is valid for all protocol settings, and L D descriptions for a specific

protocol setting (2).

Figure 2.1

X4 X8

BF DIA

Lnk/Act

X02

X01

UAux

DIA

x100 x10 x1

MS NS

0E/IP

BF DIA

X02

X01 USUAux

A B

Link/Act

E/IP

x100

x10

MS NS

G60L G30L

L D Function

DIA

L D A (for each of X1

- X8 A)

Red: peripheral error (sensor/actuator overload or short circuit)

SIO mode

Yellow: channel A status (pin 4) is "on"

Off: no error, not connected

IO-Link mode

Green: IO-Link communication present

Flashing green: no IO-Link device connected

Off: not configured for IO-Link

DIA

L D B (for each of X1

- X8 B)

Red: peripheral fault (sensor and actuator overload or short circuit at

line L+ (pin 1))

SIO mode

White: Channel B status (pin 2) is "on"

Red: Overload or short circuit at C/Q (pin 4) line

Off: no error, not connected

IO-Link mode

Red: IO-Link COM mode: IO-Link communication error or overload or

short circuit at C/Q (pin 4) line

Flashing green: no IO-Link device connected

Off: not configured for IO-Link

L D U

Green: voltage 19 V  U

 30 V

Red: voltage U

< 19 V or U

> 30 V

L D U

Aux

Green: voltage 19 V  U

Aux

 30 V

Red: voltage U

Aux

< 19 V or U

> 30 V

Red alert is only possible if, for therNet/IP, the option "Report U

Aux

supply voltage fault" is enabled in "General Diagnosis Settings" or, for

PROFIN T, the option "U

Aux

supply diagnosis" is enabled in "Global

Diagnostic Parameters."

Table 2.1

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Pepperl+Fuchs Steuereinheit Handbücher

Pepperl+Fuchs

Pepperl+Fuchs VBA-2E-KE5-IJL Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs 5500 Series Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs ICA-8DIO4M1-G20-IO Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs 7500 Series Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs WCS-EIG410 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs IUT-F190-R4-V1 Series Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs VBA-4E-G11-I-F Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs VBA-4E-KE5-IL Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs VLX-F231-B6 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs VAZ-2E2A-G20-ZPA1 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs WCS DG310 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs WCS-CG310 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs 5500 Series Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs ICE11-8IOL-G60L-V1D Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs IC-KP2-1HB6-2V15B Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs IQT-F116-R4M-V1 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs VAA-2E2A-KE1P-S/E2 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs HD2-DM-A Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs VAA-2E-G4-SN Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs VAA-2E2A-KE1-S/E2 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs LAL-SRW series Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs IC-KP2-1HB6-V15B Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs KFD2-DWB-Ex1.D Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs ICE11-8IOL-G60L-V1D Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung