Pepperl+Fuchs WCS DG310 Bedienungsanleitung

WCS DG310

WCS DeviceNet

Interface Module

FACTORY A TOMATION

MAN AL

With regard to the supply of products, the current issue of the following document is ap-

plicable: The General Terms of Delivery for Products and Services of the lectrical Indus-

try, published by the Central Association of the lectrical Industry (Zentralverband

lektrotechnik und lektroindustrie (ZV I) e.V.) in its most recent version as well as the

supplementary clause: " xpanded reservation of proprietorship"

WCS DG310

1 Introduction................................................................................. 4

1.1 Content of this Document ................................................................... 4

1.2 Target Group, Personnel...................................................................... 4

1.3 Symbols sed ...................................................................................... 4

2 Product Description ................................................................... 6

2.1 se and Application............................................................................. 6

3 Installation................................................................................... 7

3.1 Mounting ............................................................................................... 7

3.2 Electrical Connection .......................................................................... 7

4 Commissioning........................................................................... 9

4.1 Meaning of LEDs .................................................................................. 9

4.2 Meaning of Switches.......................................................................... 10

4.3 Operating Modes................................................................................ 11

4.4 Connecting the WCS Reader ............................................................ 12

4.5 Connection to the Control Panel ...................................................... 12

4.6 Data Exchange in DeviceNet............................................................. 13

4.7 EDS Configuration File ...................................................................... 14

5 Appendix ................................................................................... 15

5.1 Cable Routing in the RS-485 Bus ..................................................... 15

5.2 Meaning of F0 ..................................................................................... 17

5.3 Data Format for Connected WCS Readers ...................................... 18

5.4 Data from WCS Reader...................................................................... 18

5.5 Data Cables and Accessories ........................................................... 19

2017-12

WCS DG310

Introduction

1 Introduction

1.1 Content of this Document

This document contains information required to use the product in the relevant phases of the

product life cycle. This may include information on the following:

■

Product identification

■

Delivery, transport, and storage

■

Mounting and installation

■

Commissioning and operation

■

Maintenance and repair

■

Troubleshooting

■

Dismounting

■

Disposal

The documentation comprises the following parts:

■

This document

■

Datasheet

In addition, the documentation may comprise the following parts, if applicable:

■

U-type examination certificate

■

U declaration of conformity

■

Attestation of conformity

■

Certificates

■

Control drawings

■

Instruction manual

■

Other documents

1.2 Target Group, Personnel

Responsibility for planning, assembly, commissioning, operation, maintenance, and

dismounting lies with the plant operator.

Only appropriately trained and qualified personnel may carry out mounting, installation,

commissioning, operation, maintenance, and dismounting of the product. The personnel must

have read and understood the instruction manual and the further documentation.

Prior to using the product make yourself familiar with it. Read the document carefully.

Note!

Visit www.pepperl-fuchs.com to access further documentation for full information about the

product.

WCS DG310

Introduction

2017-12

1.3 Symbols Used

This document contains symbols for the identification of warning messages and of informative

messages.

Warning Messages

You will find warning messages, whenever dangers may arise from your actions. It is mandatory

that you observe these warning messages for your personal safety and in order to avoid

property damage.

Depending on the risk level, the warning messages are displayed in descending order as

follows:

Informative Symbols

Action

This symbol indicates a paragraph with instructions. You are prompted to perform an action or

a sequence of actions.

Danger!

This symbol indicates an imminent danger.

Non-observance will result in personal injury or death.

Warning!

This symbol indicates a possible fault or danger.

Non-observance may cause personal injury or serious property damage.

Caution!

This symbol indicates a possible fault.

Non-observance could interrupt the device and any connected systems and plants, or result in

their complete failure.

Note!

This symbol brings important information to your attention.

2017-12

WCS DG310

Product Description

2 Product Description

2.1 Use and Application

The WCS-DG310 is used as an interface between the WCS reader and the DeviceNet bus.

The data between the WCS reader(s) and the WCS-DG310 is transferred via the RS 485

interface, and from the WCS-DG310 to the control panel via the DeviceNet protocol.

You can connect up to four WCS readers of type LS221 or LS121. If you connect several WCS

readers, they must have different addresses. The WCS-DG310 meets the conditions laid down

in "DeviceNet Specification Release V2.0" and works as a DeviceNet "Group 2 only Slave."

(Vendor ID:272, device type: 12). The interface module allows transfer rates up to 500 kBaud in

DeviceNet.

WCS DG310

Installation

2017-12

3 Installation

3.1 Mounting

The dimensions of the WCS-DG310 interface module are:

23 x 116 x 115 mm (W x H x D).

The WCS-DG310 interface module is attached to a 35 mm wide DIN mounting rail ( N 50022-

35) with a snap-on fixing method.

The device is grounded via the mounting rail.

3.2 lectrical Connection

Plug X1 is located on the top side of the interface module, plug X2 on the underside.

Figure 3.1 lectrical connection

Preparing to use the RS 485 interface

1. Connect terminal 4 "Rx 422+" to terminal 6 "Tx 422+".

2. Connect terminal 5 "Rx 422-" to terminal 7 "Tx 422-".

Note!

Grounding of the mounting rail

The mounting rail must be grounded to the switch cabinet. The connection wire must have a

cross section of at least 10 mm

X1-6

X1-7

WCS.-LS221

WCS-DG310

UB+

RS 485 -

RS 485 +

RS 485 -

RS 485 +

GND

24 V (Pwr)

0 V (Pwr)

X2-1

X2-2

X1-4

X1-5

GND UB+

X3-5

DeviceNet Bus

V+

X3-4CAN-H

X3-3Schirm/shield

X3-2CAN-L

X3-1V-

Note!

To use with an RS 485 interface, terminal "Rx 422+" on plug X1 must be connected to terminal

"Tx 422+", and terminal "Rx 422-" must be connected to terminal "Tx 422-".

Terminal Designation

4 Rx 422+ RS 485+ data line to WCS reader

5 Rx 422- RS 485- data line to WCS reader

6 Tx 422+

7 Tx 422-

Table 3.1 Terminal X1

2017-12

WCS DG310

Installation

Connecting the interface module to the voltage

Connect the operating voltage (10 VDC...30 VDC) to terminals 1 and 2 of the 4-pin plug X2 on

the interface module.

The "Power" L D lights up green.

Terminal Designation

1 UB (Pwr) Operating voltage interface module/

operating voltage WCS reader

2 0 V (Pwr) Ground interface module/ground

WCS reader

Table 3.2 Terminal X2

Caution!

Damage to the device

Connecting an alternating current can damage the device or result in it malfunctioning.

Connect interface module to direct current (DC).

Note!

Grounding of the mounting rail

The mounting rail must be grounded to the switch cabinet. The connection wire must have a

cross section of at least 10 mm

WCS DG310

Commissioning

2017-12

4 Commissioning

4.1 Meaning of L Ds

Power:

The "Power" L D is green: The WCS-DG310 interface module is correctly connected to the

power supply.

BusPower:

The "Power" L D is green: The L D is connected directly to the electrically isolated supply

voltage of the DeviceNet side.

BusState:

State:

The "State" L D is green: Data exchange is taking place with the WCS readers. Using the 4

" rror No/Select ID" L DS, the number of the currently polled WCS reader is displayed.

The "State" L D is red: The interface module has detected an error or a warning. The interface

module displays the binary coded error and/or warning number via the " rror No/Select ID"

L Ds.

“BusState" L D DeviceNet interface state

Lights up green Connected to the DeviceNet master

Flashes green No connection to the DeviceNet master

Lights up red Serious error on DeviceNet bus (for example, duplicate MAC ID)

Flashes red Recoverable error (e.g., timeout error)

Flashes red/green Communication errors

Table 4.1 "BusState" L D display

rrorNo/Select ID Reader address

8 4 2 1

00010

00101

01002

10003

Table 4.2 Display of the 4 L Ds " rror No/Select ID" when the "State" L D lights up green

rror (No. 1...5): Switch the interface module off and back on. If the error occurs

again, the module must be replaced.

Warning (No. 6...15): The warning provides information. The interface module displays

the warning for one minute and then resets automatically.

2017-12

WCS DG310

Commissioning

4.2 Meaning of switches

The WCS-DG310 interface module has 6 switches with the following

functions:

Rx 422/Tx 422 Termination (serial interface)

If the interface module is operated as the first or last physical device in an RS485 bus, there

must be a bus termination on this gateway. To do this, set the slide switch "Rx 422 Termination"

to "Off" and the slide switch "Tx 422 Termination" to "On". This activates the RS 485 terminator

(150 Ω) built into the interface module.

If you connect only one WCS reader to the WCS-DG310, you must always activate the RS 485

terminator.

rrorNo/Select ID L D rror number A description of the fault

L D8 L D4 L D2 L D1

0 0 0 0 0 Reserved

0 0 0 1 1 Hardware error

0 0 1 0 2 PROM error

0 0 1 1 3 Internal memory error

0 1 0 0 4 Fieldbus hardware error or incorrect

fieldbus ID

0 1 0 1 5 Script error

0 1 1 0 6 Reserved

0 1 1 1 7 Communication WCS reader, RS

send buffer overflow

1 0 0 0 8 Communication WCS reader, receive

buffer overflow

1 0 0 1 9 Communication WCS reader, RS

timeout

1 0 1 0 10 General fieldbus error

1 0 1 1 11 Parity or frame check error

1 1 0 0 12 Reserved

1 1 0 1 13 Fieldbus configuration error

1 1 1 0 14 Fieldbus data buffer overflow

1 1 1 1 15 Reserved

Table 4.3 Meaning of the error codes (4 L Ds display " rror No/Select ID", if the "State" is illuminated

red and thus indicates an error or a warning)

Switch designation Function

Rx 422 Termination Switchable Rx 422 terminator for the serial interface

Tx 422 or RS 485

Termination

Switchable Tx 422 or RS 485 terminator for the serial interface

Termination (DeviceNet) Switchable terminator for the DeviceNet bus

Rotary switch S4 Set the number of connected WCS readers (see see chapter 4.4)

Rotary switch S5 No function (always remains in position 0)

DIP switches Set the node ID and baud rate (see see chapter 4.4)

Table 4.4 Meaning of the switches on the WCS DG-310 interface module

Inhaltsverzeichnis

Andere Pepperl+Fuchs Steuereinheit Handbücher

Pepperl+Fuchs

Pepperl+Fuchs VAA-2E1A-CB10-SJ/E2J-FL Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs EtherCAT WCS-ECG110 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs ICE1-8IOL-S2-G60L-V1D Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs PSE4-SC-01 Betriebsanleitung

Pepperl+Fuchs

Pepperl+Fuchs VBA-4E4A-G20-ZEJ/M3L-P9 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs VAA-2E2A-KE1-S/E2 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs IC-KP2-2HB6-V15B Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs PS1000-D2-24.40.RM Handbuch

Pepperl+Fuchs

Pepperl+Fuchs VU121 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs WCS-PNG110 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs IUT-F190-R4-V1 Series Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs LAL-SRW series Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs 5500 Series Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs VAA-4E4A-G20-ZEJ/M2L-P7-GEB Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs VAZ-2E2A-G20-ZPA1 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs ICA-8DIO4M1-G20-IO Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs HD2-DM-A Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs VU121 Referenzhandbuch

Pepperl+Fuchs

Pepperl+Fuchs ICE11-8IOL-G60L-V1D Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs IC-KP2-1HB6-2V15B Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs KFD2-DWB-Ex1.D Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs IC-KP2-1HB6-V15B Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs IC-KP2-2HB17-2V1D Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs VBA-2A-KE5-IL/UL Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung