Perstel DMR132vlm Bedienungsanleitung
User's Manual
T-DMB Receiver
Thanks for purchase of Perstel DMB Receiver.
Please read User’s Manual before use.
Please hold the product firm-
ly with mounting bracket,
and have lower part of
mounting bracket placed on
dashboard.
Before use
Safety precautions 02
Before use
Safety precautions
01
For safety, please have
speed detector cable
engaged with tachometer
at all times.
dashboard Please do not
operate the product while
driving, or it may cause
serious accident.
Please do not use the prod-
uct while engine is not work-
ing, or vehicle battery may
be discharged.
Please do not too much
raise volume level, or it
may take your attention
away while driving.
Please keep the remote
controller handy.
Power On!
Manual
PUSH
Front
glass
dashboard
Stop the engine for installation.
Please do not block eyesight
and/or airbag with the product.
Do not turn on the product
before turning on the engine. Install the antenna at the
center of loop for best
reception.
Do proper connection of
cables, or it may cause
damage to the product.
The product is designed to
best work at 5 ~ 25C.
Please maintain the temper-
ature for best use in deep
summer and winter.
Please clear the product
with dry clothes. Do not
apply chemical or deter-
gent.
Do not dismantle the prod-
uct without proper knowl-
edge, or warranty will be
void.
The product is packaged with
12V cigar lighter charger.
Please prepare 24V cigar
lighter charger to use in buses
and/or trucks.
Package contents
Before use 04
Before use
Intellectual Property Rights
03
Intellectual Property Rights
PERSTEL holds intellectual property rights for those material used in this user's manual.
Any content or image is not allowed for copying, transforming without prior consent by
PERSTEL.
2005 PERSTEL INC. All Rights reserved.
Legal disclaimer
- Manufacturer, importer, or distributor is not liable for any contingent damage caused by
misuse of the product.
- Color, specification and contents are subject to change without prior notice.
Optional accessories
These accessories are sold separately.
DMR132VLM Remote
controller User's manual
12V cigar lighter
charger Mounting bracket Antenna set
Wall adapter
(indoor 12V)
Car pack audio
connector I indoor antenna
cable & connector Headrest
mounter
On-dash mounter Rod anteanna 24V cigar lighter
charger
Speed detector
cable
Before use 06
Before use
Intellectual Property Rights
05
1. Product installation
Insert connection
joint ( ) in the set
bracket rail.
Tighten screw ( ) till
two brackets are
firmly fixed. And
tighten locking
screw ( ).
Secure proper space on
front glass. Place suction
cup on the glass and
push the suction lever
over the suction cup.
Bend zebra rod to
secure best visual
angle.
Place DMR132 on set bracket. Insert screw in the
screw hole at bottom of DMR132, and screw it tight.
For installation in deep winter, the suction cup
may become too hard to use. Place it under hot
air blow to make it soft before installation.
DMR132 may too much shake while driving if it
hangs high in the air. Adjust height of suction
cup, and bend zebra rod to have lower part sup-
ported with vehicle dash board.
Product installation
For safety reasons, it is highly recommended to consult installation work with local
installation shops or dealers. Installation work may be different by car type.
For safety reasons, please have speed detector cable engaged with tachometer at all
times.
Far safety reasons, please turn off the engine for the entire installation procedure.
Front
glass
dashboard
(Mounting bracket)
(Set bracket)
Before use
Intellectual Property Rights 08
Before use
Intellectual Property Rights
07
2. Antenna mounting
Insert antenna in magnet base
and screw it tight.
4. Speed detector connection
Speed detector is a mandatory device to secure drivers’ safety while driving. Speed
detector detects vehicle speed and automatically shut off display screen when vehicle
is moving (audio remains alive). Connection may vary depending on vehicle type, so
please consult with mechanic for speed detector connection.
3. Power connection
PUSH
123456
D
D
FF RPT
Plug in power cable to the DC IN port, and plug in cigar lighter charger to the socket.
For best reception, place antenna on the loop using magnet base.
For best performance, fasten antenna connector tight.
It is recommended to wrap cables with waterproof tapes.
Organize excessive cables with cable holders. Plug in one end of speed detector cable to SPEED DET port. And, connect another end of speed
detector cable to vehicle’s speed pulse signal line. Display screen will be shut off when vehicle is
moving.
Please consult with local mechanic since vehicles’ pulse signal position varies by vehicle type.
In case speed detector is not properly connected as stated, display screen remains active while
driving, and it may cause serious incidents.
Any incident caused by absence of speed detector will be responsibility of users or drivers.
Manufacturer will not be responsible for the consequences at any degree.
Please consult with mechanic when connecting power directly from vehicle.
Please be sure to clean dusty from cigar lighter charger socket.
Screw in antenna cable with
antenna connector.
Before use
Intellectual Property Rights
09
Installation of optional items
1. Rod antenna
Screw in the rod antenna to
antenna port firmly. Turn on the unit, and simulate antenna
position till best reception is obtained.
When using on table, unfold the sup-
port bar from the rear, and stretch it to
convenient angle.
2. Indoor wall adapter
When using the product at home,
please replace cigar lighter charger with
indoor wall adapter like above diagram.
Before use
Intellectual Property Rights 10
3. Support bar
Insert connection joint
in the set bracket rail,
and screw it tight.
Before placing the whole set of unit,
please clean up mounting floor. Peel
off protection vinyl from adhesive
tape when ready.
Place the whole set on the floor (on
dash board or else), and make sure
adhesive tape hold the set firmly.
Unscrew rear screw to
adjust angle. Fasten the
rear screw when the
adjust is done.
Place the DMR132 on
the set bracket and fas-
ten locking screw.
On-dash mounting bracket works more stable than on-glass mounting bracket.
It is matter of choice and matter of convenience.
4. On-dash mounting bracket
Before use
Controls diagram 12
Controls diagram
Remote control I/F
Power LED (Red)
Tune LED (Green)
Favorite memories
LCD
Navigation
MENU
Display
Antenna port
Speaker
USB
port
Power
switch
Support bar
screw
mounting
hole
DC
In
Speed detector port
Audio out
USB port is only for upgrading system software in the future. Please consult
with local dealer or manufacturer for upgrade.
Indoor antenna & adapter is designed for those who use normal TV antenna
system. Please check TV system before purchase of this accessory.
Before use
Intellectual Property Rights
11
Plug in antenna adapter to one end of
antenna cable. Plug in and screw the antenna
adapter to DMR132 ANT port.
Another end of antenna cable is
for wall TV antenna socket. Plug it
gently to the socket like connect-
ing cable TV antenna.
Depending on country and broadcast system, indoor antenna cable & adapter set
enables users to watch DMB using TV antenna.
5. Indoor antenna cable & adapter
Top
Rear Side
Operation
Functionality of remote controller 14
Operation
Functionality of remote controller
13
Functionality of remote controller
Open the battery compartment by
using tiny pin, and replace battery
following polarity indication. Slide
battery compartment back to origi-
nal position.
Battery replacement (Remote controller)
Power
Turn on and off of DMR132
Menu
Enter the menu or escape the menu.
List
Shows preset list or hides the list.
Display
Shows information of current service.
OK/ Mute
Menu mode- For confirming Selection.
Long key when receiving - Current service will be saved in preset list.
(Press it for more than 3 seconds.)
Short key when receiving -Audio will be muted.
Navigation
Up/Down - For volume control, or scroll up and down the menu in menu
mode.
Left/Right - For service change while receiving signal, or entering or
escaping menu in menu mode.
Favorites
Press to instantly access to saved favorite memories.
While receiving services, press it (1 ~ 5) and hold to store or overwrite
favorite memory.
List
Enter/ Mute
Menu
Display
Favorite
Navigation
Operation
Power on 16
Operation
Functionality of remote controller
15
Turn the power on using slide switch
on the left side of the product.
Press POWER button to activate/
deactivate the DMR132.
To use remote controller, please keep main power switch (slide switch on the left side of
DMR132) “ON” at all times.
Left side
Remote controller
LCD indicator Power on
DMB mode
DAB mode
Signal strength
Information window
Ensemble
Service name
Tune mode
Current time
Current time
Ensemble name
Service name
DLS info
Signal strength
Tune mode
Volume level
Volume level
Operation
Mute/ Unmute 18
Operation
Volume control
17
Press Mute button shortly to mute
audio.To unmute audio, press
mute button again, or adjust vol-
ume button.
Volume control Mute/ Unmute
Press down button to lower
volume level.
Press up button to raise vol-
ume level.
Press up button to
raise volume level. Press down button to
lower volume level.
DMB mode DAB mode
Inhaltsverzeichnis
Andere Perstel Empfänger Handbücher
