Phase TOCR02 Bedienungsanleitung

TOCR02

2 PART MICRO MOTION

SENSOR W/IR REMOTE

CONTROLLER

Power Circuit Part

PIR Motion Sensor

INTRODUCTION

The use of occupancy detectors in commercial and

industrial applications can significantly reduce energy

usage reducing both energy costs and helping the

environment.

The Titan 360 degrees MICROSENSITIVE 2 PART

flush mount OCCUPANCY DETECTOR uses passive

infrared sensors (PIR) which react to changes in

temperature emitted by the slight motion of persons or

objects passing through its detection area. The PIR

sensor automatically operates the connected load

when an area is occupied. After a preset time on

non-activation (when an area is vacated) the load will

be switched off. In addition the built in photocell takes

natural light (daylight) into account when determining

its activation..

It also incorporates lux memory feature which means

the sensor is able to record and memorize the lux

level when the internal connected light fixture is turned

on by the Micro Motion Sensor. However, once the

natural light lux level is higher than that of the internal

artificial light even if the movement still exists, the

sensor will switch off the internal light fixture thus

saving energy.

The product also incorporates a 2 part structure

allowing the initial installation to be made and the

detector removed to avoid damage during painting,

maintenance etc.

The product is also supplied with a two channel Infra

Red remote control for remote operation.

Note: Read this entire manual before you start to

install the system.

SAFETY PRECAUTIONS

Be sure to switch off power source before

installing.

Make sure that the power wiring comes from

circuit with an external 16A miniature circuit

breaker for the short circuit protection or a

suitable fuse.

The unit is designed to be mounted on the

ceiling.

(FIGURE 1)

FIGURE 1

The installation of this device should be made by

a qualified electrician.

CHOOSING A MOUNTING LOCATION

Avoid aiming the motion sensor at heating vents,

air conditioners or objects which may change

temperature rapidly.

Prior to mounting the light fixture, remember to

position the motion sensor so that a moving

object cuts “across” its beams, not directly

towards them.” (FIGURE 2)

FIGURE 2

Note: Micro motion detection can be made within

a radius of 3m around the sensor; regular motion

detection can be made within a radius of 6m

around the sensor.

INSTALLATION

A drill and a screwdriver are needed for installation.

Select a location for the unit based on the coverage

angles shown in FIGURE 3.

FIGURE 3

WIRING INSTRUCTION

(1) Switch off the power source or wall switch.

(2) Using a flat blade screwdriver to detach the PIR

motion sensor and power circuit part. (FIGURE

FIGURE 4

(3) When connecting to one Micro Motion Sensor, the

wiring connection is shown hereunder: (FIGURE

5a)

FIGURE 5a

By connecting to two Micro Motion Sensors, the wiring

connection is indicated as below: (FIGURE 5b)

FIGURE 5b

Note: A pulse switch (S2,S4) is connectable to the

unit, enabling manual operation.

(4) A 60mm hole should be drilled in the ceiling, put

the power circuit to the hole and secure it using to

the mounting surface using the screws provided.

Fix the PIR motion sensor to the power circuit part

by simply clicking in place (FIGURE 6).

FIGURE 6

SETTING THE LIGHTING SYSTEM

Please test the motion sensor function before testing

the IR Remote Controller.

Test Mode :

Turn the LUX control and the TIME control anti

clockwise – the TEST position. (FIGURE 7)

FIGURE 7

Turn on the wall switch. The light will turn on for

about one minute to warm up. During warm-up

period, the light turns on continuously. After one

minute is expired, the light will turn off.

Walk through the detection area, the light will turn

on continuously. If and when movement is

ceased, the light will be on for one second before

turning off.

(1) TIME ADJUSTMENT

The TIME adjustment controls how long the light will

stay on after the last motion has been detected. Time

setting is adjustable from 5 seconds to 12 minutes.

(FIGURE 8)

ABOUT 5 SECONDS ABOUT 12 MINUTES

FIGURE 8

Note: T serves as a short-time impulse, which allows

you to control automatic switching of staircase lighting

or timer.

(2) LUX ADJUSTMENT

The LUX adjustment determines at what light level the

lighting system will start operating when you set the

sensor to automatic operation.

Provisionally turn the LUX control knob clockwise to

the moon (dusk) position (FIGURE 9). Turn the LUX

control knob slowly anti-clockwise until the light comes

on. In this provisional setting mode, the motion

sensor remains inactive during daylight. At dusk

when you find it is the LUX level desired for operation,

simply set the LUX control knob to the position which

becomes active as daylight declines. The light turns

on when you move and turns off when you stop.

Wait for the light to turn off before moving again to test

the sensor.

FIGURE 9

(3) CHANNEL SELECTION

To avoid radio signal interference, and operate

separate banks of detectors on a single remote, you

are able to select different channels through channel

switch. Select channel 1 or 2 on the sensor for

grouping the connected light fixtures in the same or

different zone.

E253R IR Remote Controller

314

FIGURE 10

3-button and channel selection slide switch are shown

on the front cabinet as follows: (FIGURE 10)

AUTO

ON

OFF

CHANNEL SWITCH

LOADING THE BATTERY

(1) Use a flat blade screwdriver to detach the battery

cover from the cabinet. (FIGURE 11)

FIGURE 11

(2) Insert a 12V alkaline battery to the battery

compartment and refit the battery cover. (FIGURE

12)

FIGURE 12

OPERATION

By using IR Remote Controller to your NL5703, you

can easily select three modes of operation: automatic,

on and off.

Make sure the Micro Motion Sensor and IR Remote

Controller are set at the same channel. (FIGURE

13a & 13b)

1 2

OFF

AUTO

1 2

OFF

AUTO

CH21

FIGURE 13a & 13b

(1) AUTOMATIC OPERATION

Before operating the IR Remote Controller, please

make sure the sensor is in proper setting for Auto

mode.

The sensor detects motion automatically according to

its time and lux setting.

(2) ON

To keep the light on regardless of motion, you can

press “On” button on the IR Remote Controller. The

light will be continuously on.

The LED inside the sensor will light up when receiving

IR Remote Controller’s signal.

(3) OFF

By pressing “Off” button to deactivate the light from

illumination.

User can also set the motion sensor back to Auto

operation by pressing “Auto” button on the IR Remote

Controller.

(4) MANUAL OPERATION

By using pulse switch to manually control the

connected light fixture to be turned on or off.

If the connected light fixture has been turned on,

simply press the pulse switch to turn off. If and when

it has been turned off, press the pulse switch to turn

on and the connected light fixture will be turned off

automatically according to the time setting.

(5) LUX MEMORY

Under auto mode, the Micro Motion Sensor is

triggered either by movement or by pressing the pulse

switch, the sensor will automatically record and

memorize its initial lux level. When the ambient lux

level is 1.5 times higher than that of initial lux level, the

sensor will switch off the connected light fixture to

save energy.

This feature is valid subject to the TIME setting being

fixed more than one minute. It is irrelevant to lux

adjustment.

SPECIFICATIONS

Power Requirement AC 220 ~ 240V / 50Hz

Operating Load

(maximum) Max. 2000W Incandescent

or 1500W fluorescent

Up to 210w LED (dimmable

recommended)

Detection Angle Up to 360° at 20°C

Detection Range

(Micro Movement) 3~4m radius at 20°C

Detection Range

(Regular Movement) 6~8m radius at 20°C

Mounting Height Recommended 2.5~3.5m

Ceiling Mount

IR Controller Channel 1 & 2

Auto / On / Off

IR Controller Range 8M OPEN SPACE

IR Controller Battery 23A 12V

Wall switch control ON/OFF

Pulse switch control ON/OFF

Time Adjustment Adjustable 5 seconds ~ 12

minutes

Lux Adjustment Yes

Lux Memory Yes

Warm Up Time About 1 min.

Protection Class II

*Specifications are subject to change without notice.

A501110061R01

Warning:

Do not dispose of electrical appliances as unsorted

municipal waste, use separate collection facilities.

Contact your local government for information

regarding the collection systems available.

If electrical appliances are disposed of in landfills or

dumps, hazardous substances can leak into the

groundwater and get into the food chain, damaging

your health and well-being.

Inhaltsverzeichnis

Andere Phase Zubehör Handbücher

Phase

Phase XtalX LUSQ1 Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung