Philips DUS804C-UP Bedienungsanleitung

DUS804C-UP

Ceiling Mount Universal Sensor Installation Manual

This unit is for indoor use only. This unit is designed for installation in a 64mm diameter hole where the ceiling void is at

least 40mm deep. Select an appropriate indoor mounting location, as detailed in the location guidelines on the following

The DUS804C-UP is a low profile mount 360º ceiling mount sensor that combines motion detection via

both Ultrasonic (UP) & passive inferred (PIR), infra red remote control reception (IR) and ambient light

level detection (PE) in the one device.

In applications such as office buildings, lecture theatres, and homes, the DUS804C-UP universal sensor

can be utilised to detect motion and switch on the lights automatically when motion is detected. When

rooms have been unoccupied for a certain amount of time, lights can be automatically dimmed or switched

off to provide energy savings.

The unit also incorporates a segmented click-up bezel surrounding the motion sensor element. This

enables a portion of the sensing field to be readily masked to prevent nuisance detection from adjacent

doorways or corridors. The same sensor provides IR control reception to enable full remote control over

lights, audio-visual equipment and blinds. A range of hand held infra-red transmitters to complement

DUS804 series universal sensors are available.

In situations where it is critical to maintain precise lighting control for individual workspaces, such as an

office workstation or even air traffic control centers, the DUS804C-UP facilitates light compensation. The

DUS804C-UP can also perform multiple functions at the same time so that automatically going to “Daylight

Harvesting” mode once motion has been detected for additional energy savings.

instructions

2DUS804C-UP Installation Manual Rev D.docx

pages. Note that the product has two functions, and the optimum mounting location for each individual function may

conflict with each other, and may require use of multiple sensors.

DUS804C NETWORK CONNECTIONS:

Motion detection installation steps

•An ultrasonic sensor should never be located within 17.5 meters of another ultrasonic sensor.

•Chose a location where it may face doorways etc which could cause false triggering.

•Position the sensor so it is between 2.1 and 4.0m from the floor. Optimum height is 2.4m

•Position the sensor so it is at least 1m away from electrical lighting such as neon and fluorescent lights

•Position the sensor as to avoid exposing it to direct sunlight. Sensor should be at least 2.5m from horizontal or

vertical air ducts

•Position the sensor where pedestrian traffic is likely to walk across the detection zones

•Fix the sensor to a firm section of ceiling. Sensor can be surface mounted using ring provided.

•Note that for the DUS804C-UP coverage area is rectangular (see Motion Detector coverage diagram)

•When terminated and power there are three indicating LED‟s for the following information

oBlue = Low network voltage. The sensor must receive minimum of 12VDC from the Dynet network. If

the right network voltage is not present at the sensor terminals when the whole system is powered,

then additional network power supplies (DDNP1501) will be required.

oGreen = Ultrasonic detection activity

oRed = PIR detection activity

• When terminated correctly and powered from the Dynet network the sensors LED‟s will flash for 5 min every time a

Dynet push button is pressed. This is so the installer can confirm the sensor is terminated correctly with other network

devices.

• Only after all network devices are confirmed to be terminated correctly can the commissioning of the system begin.

PIR sensor

Network sign

on button & IR

window

Ultrasonic

sensors

Recommended Cable Types

Belden: 9503

Garland: MCP3S

Hartland: HCK603

M&M Cable: B2003CS

Dynalite: DYNET-STP-CABLE

STANDARD CABLE CONNECTION

Recommended Cable Colours

Green/White Pair paralleled for GND

Orange/White Pair paralleled for +VE

Blue/White Pair Blue for DATA +

White for DATA -

Light level sensor

Indicating LED’s

motion detector coverage at 2.4m mounting height

DUS804C-UP Installation Manual Rev D.docx 3

photo electric cell mounting location

• Position the sensor so it “sees” a combination of artificial light and natural

Light

• Position the sensor so it is not directly exposed to artificial light or sunlight

• For programming instructions refer to Dynalite Tech Note - Setting up PE

functions

Lens pattern –DUS804C-UP

Mounting Dimensions

specifications

4DUS804C-UP Installation Manual Rev D.docx

Warranty policy

Dynalite warrant to the original purchaser for a period of twenty four (24) months from the date of shipment ex-factory of the

equipment that should the equipment prove defective by reason of improper workmanship or material, Dynalite will repair or replace

the same without charge provided the equipment has not been improperly installed, operated, repaired, damaged or abused. The

warranty granted herein is limited to repair or replacement only. Dynalite has the right to substitute any warranty item not on the

current price/equipment list. As far as the law permits, Dynalite shall not be liable for any loss or damage caused to property or

persons arising from any cause whatsoever. This warranty is subject to the return of the equipment to Dynalite, or the Dynalite

authorised distributor who supplied the equipment (the „Supplier‟), by prepaid freight within the twenty four (24) months warranty

period. Where Dynalite, or the Supplier, agree to a site visit during the warranty period and it is found to be an operational problem,

and not subject to warranty in that event, then a field service call out charge will apply. Contact Dynalite or the Supplier for details.

Dimtek, DyNet and DLight and associated logos are the registered trademarks of Dynalite Intelligent Light Pty Ltd. Not to be reproduced without permission.

E-Mail: dynalite.info@philips.com Web: philips.com/dynalite

DUS804C-UP:

PIR:

Maximum detection range: 5.0m

Detection area 7.4m x 5.6m ellipse (at a height

of 2.4m

Detection speed: 1.0m/s

Detection object: 700mm x 250mm

Detection zones: 64

LED activation indicator

Sensor: Quad element pyro-electric

R.F.I Immunity:>15V/m @ 10 –1000MHz

Ultrasonic:

Normal motion detection area:

8m x 16m (128m2 coverage)

Transducer pairs 2

Operating frequency: 32KHz

PE Cell:

Range <5 lux to >5000 lux (reflected)

Automatic “Daylight Harvesting” mode

Indicating LED:

Blue = Low network voltage / server required

Green = Ultrasonic detection activity

Red = PIR detection activity

Infra Red Remote Control Receiver

Range up to 6m

LED activation indicator

Can be used with DTK500 series infra red remotes

or other learning IR remotes controls

Controls

Walk test/ LED indicator

Service switch

Control IO

Serial Port –RS485 Dynet 80mA 12VDC min

The supply of the sensor must never drop bellow

12VDC.

Terminals

Standard:

5 way removable terminal strip, 1 x 2.5mm2 max

conductor size

Operating Environment

0oC to 40oC ambient temperature

0% to 90% RH non condensing

Dimensions

90mm diameter x D 26mm

Weight

Packed weight 0.25kg

Compliance

CE, C-tick

Andere Philips Zubehör Handbücher

Philips

Philips US2-PH62022 Bedienungsanleitung

Philips

Philips M1131A Bedienungsanleitung

Philips

Philips OlfaPure LUMOP700BLKX1 Bedienungsanleitung

Philips

Philips SCF302/13 Bedienungsanleitung

Philips

Philips Somneo Sleep and Wake-Up Light Programmierhandbuch

Philips

Philips OccuSwitch LRM1070/00 Bedienungsanleitung

Philips

Philips SCF616/10 Bedienungsanleitung

Philips

Philips CRP489 Bedienungsanleitung

Philips

Philips InfraCare HP3631 Bedienungsanleitung

Philips

Philips CRP311 Bedienungsanleitung

Philips

Philips SB3B1819 Bedienungsanleitung

Philips

Philips HF3480 Bedienungsanleitung

Philips

Philips DLP6100V Bedienungsanleitung

Philips

Philips EasyAir SNS300 Bedienungsanleitung

Philips

Philips HF3505 Bedienungsanleitung

Philips

Philips SPF1002N Bedienungsanleitung

Philips

Philips Norelco 7200 series Bedienungsanleitung

Philips

Philips SAC2560 Bedienungsanleitung

Philips

Philips CRP136 Bedienungsanleitung

Philips

Philips CRP359 Bedienungsanleitung

Philips

Philips INFRACARE HP3643 Bedienungsanleitung

Philips

Philips CRP396 Bedienungsanleitung

Philips

Philips HX7990/02 Bedienungsanleitung

Philips

Philips CRP328 Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung