Philips Dynalite DUS704W Bedienungsanleitung

Unit 6, 691 Gardeners Road Mascot NSW 2020 Australia

t +61 8338 9899 f +61 2 8338 9333 [email protected]m ABN 33 097 246 921 Philips.com/dynalite

DUS704W

Wall Mount Universal Sensor Installation Manual

The DUS704 series combine motion detection (PIR), infra red remote control reception (IR) and

ambient light level detection (PE) in the one device. In applications such as homes, lecture

theatres and office towers, DUS704W universal sensors can be utilised to detect motion and

switch on the lights.

When rooms are unoccupied, lights can be automatically dimmed or switched off to provide

energy savings. The same sensor provides IR remote control reception to give full control over

lights, audio-visual equipment and blinds. A range of hand held infra-red transmitters to

complement DUS704W series universal sensors.

In situations where it is critical to maintain precise lighting control for individual workspaces, such

as a flight control tower or office workstation, the DUS704 facilitates light compensation. The

DUS704W can be placed in an automatic “Daylight Harvesting” mode for energy savings.

installation steps

2DUS704W Installation Manual Rev I

1. * WARNING * Do not touch the Pyro Sensor with your fingers. For indoor use only and not to be

used as a sensor for integration to a security system.

2. Select an appropriate indoor mounting location, as detailed in the location guidelines on the following

pages. Note that this product has three functions, and the optimum mounting location for each

individual function may conflict with each other, and may require the use of multiple sensors.

3. Remove the cover from the base unit by un-clipping the bottom of the cover and hinging it upwards.

4. Screw the base unit to the wall, ensuring the unit is mounted vertically. Pass the data cable through

the cable entry hole.

5. Ensure that the lens is properly mounted

6. Terminate the data cable as shown below.

7. Use silicon sealant to seal any cable entry and screw holes to prevent air draughts, dust and insects

from entering the enclosure.

8. Replace the cover onto the base unit by locating it in the top clip position then hinging it downwards.

Remove the screw cap at the bottom of the housing, insert and loosely tighten the supplied

screw, then replace the screw cap. Ensure that the housing is proper enclosed and sealed

internal view

connecting data cable

DUS704W Installation Manual Rev I 3

motion detection mounting location

• Fix the sensor to a firm section of wall

• Position the sensor so it is between 1.1 and 3.1 metres from the floor. Optimum height for the sensor is 2.1

metres.

• Slide the circuit board up or down so the marker on the housing matches up with the installed height on the

scale provided on the right hand side of the circuit board.

• Position the sensor so it is at least 2 metres away from electrical lighting such as neon and fluorescent

lights.

• Position the sensor as to avoid exposing it to direct sunlight and heating / cooling sources.

• Keep data cables away from electrical wiring.

• Select a location where persons are more likely to walk across the detection “fingers” rather than into them

(see diagram below).

• For programming instructions refer to Dynalite Tech Note –Setting up Motion Detection functions.

motion detection lens pattern

INSTALLATION DETA ILS

DIMTE K 110

INPUT: 230 V 5 0-6 0Hz 10 A

OUTPUT: 1 x230V 10A

MOUNT VER TICAL LY

AGAINST WALL

ENSURE G OOD VENTI LATION

FOLLOW INST ALLAT ION

INSTRUCTIONS

Unit6-11 9 /133 M cE VOY S t. A lexandria

NSW 2015A USTRA LIA

Manufactured by:

ISOLATEF ROM

MAINSS UPPLY BEFO RE

REMOVING THISC OV ER

NOUS ER SERV ICEABLEPA RT S INSIDE

SERVICE BYQ UALIFIE D PERSONNEL ONLY

INSTALLATION DETA ILS

DIMTE K 110

INPUT: 230 V 5 0-6 0Hz 10 A

OUTPUT: 1 x230V 10A

MOUNT VER TICAL LY

AGAINST WALL

ENSURE G OOD VENTI LATION

FOLLOW INST ALLAT ION

INSTRUCTIONS

Unit6-11 9 /133 M cE VOY S t. A lexandria

NSW 2015A USTRA LIA

Manufactured by:

ISOLATEF ROM

MAINSS UPPLY BEFO RE

REMOVING THISC OV ER

NOUS ER SERV ICEABLEPA RT S INSIDE

SERVICE BYQ UALIFIE D PERSONNEL ONLY

Connect Data Cable in a "Daisy Chain"

serial cable permanent connectors

connect data cable in a “daisy chain”

Recommended Cable Colours

Green/White Pair paralleled for GND

Orange/White Pair paralleled for +VE

Blue/White Pair Blue for DATA

White for DATA-

Recommended Cable Types

Belden: 9503

Garland: MCP3S

Hartland: HCK603

M&M Cable: B2003CS

Dynalite: DYNET-STP-CABLE

Side view

Top view

optional motion detector lens

4DUS704W Installation Manual Rev I

In addition to the supplied Wide Angle lens, An option for a long range lens is available for corridor

applications:

• DUS704W Long Range – Useful for monitoring a long thin space such as a corridor.

Contact your local supplier for more details

infrared receiver mounting location

• Position the sensor so it is within 6 meters of the intended operating positions of the infrared transmitter

• Position the sensor so it is not directly exposed to light, especially incandescent and sunlight, both of which

can substantially reduce IR range

• Keep data cables away from electrical wiring

photo electric cell mounting location

• Position the sensor so it “sees” a combination of artificial light and natural

light

• Position the sensor so it is not directly exposed to artificial light or sunlight

• Keep data cables away from electrical wiring

• For programming instructions refer to Dynalite Tech Note - Setting up PE

functions

6.0 Meters Max

Optional Lens –DUS704W Long Range

specifications

DUS704W Installation Manual Rev I 5

DUS704W Instruction Manual Rev I.doc. Specifications and design subject to change without notice.

Philips Dynalite manufactured by WMGD Pty Ltd (ABN 33 097 246 921). Unit 6, 691 Gardeners Road Mascot NSW 2020 Australia Tel: +61 2 8338 9899 Fax: +61 2 8338 9333

E-Mail: dynalite.inf[email protected] Web: Philips.com/dynalite

Motion Detector

Wide Angle Wall Mount PIR Detector

Range 12m x 90O (standard lens)

Mounting height: 1.1m to 3.1m

LED activation indicator

Adjustable Pulse Count & Sensitivity

Detection zones: 20 dual element zones

Sensor: Dual element pyro-electric

R.F.I. Immunity: >15V/m @ 10- 1000MHz

Optional lens:

* 30m x 30O Long Range

PE Cell

Dynamic range < 5 lux to > 5000 lux

Automatic “Daylight Harvesting” mode

Can be used for light measurement

Installation Position

Wall mount, indoor use only

Infra Red Remote Control Receiver

Range > 6m

LED activation indicator

Can be used with DTK500 series

Infra Red remotes or other learning

IR Remote controls

Dimensions

H 85mm x W 66mm x D 45mm

Control IO

Serial Port –RS485 DyNet

DyNet DC Load

20mA

Setup

All functions remotely

programmable

Weight

0.1Kg Packed

Inhaltsverzeichnis

Andere Philips Zubehör Handbücher

Philips

Philips CRP382 Bedienungsanleitung

Philips

Philips Dynalite DUS360CR Bedienungsanleitung

Philips

Philips P-5611-B Bedienungsanleitung

Philips

Philips CRP324 Bedienungsanleitung

Philips

Philips CRP149 Bedienungsanleitung

Philips

Philips EasySense SNS211 MC Bedienungsanleitung

Philips

Philips CA6521 Bedienungsanleitung

Philips

Philips HP3621 Bedienungsanleitung

Philips

Philips CRP146 Bedienungsanleitung

Philips

Philips SAC2550W Bedienungsanleitung

Philips

Philips OlfaPure Bedienungsanleitung

Philips

Philips HF3480/60 Bedienungsanleitung

Philips

Philips VSS3901/00 Bedienungsanleitung

Philips

Philips SAC2540 Bedienungsanleitung

Philips

Philips sonicare AirFloss Ultra Bedienungsanleitung

Philips

Philips InRange AEA1000 Bedienungsanleitung

Philips

Philips EasySense SNH210 MC Bedienungsanleitung

Philips

Philips LFH7177/03 Bedienungsanleitung

Philips

Philips HF3510 Bedienungsanleitung

Philips

Philips DLA81819H Bedienungsanleitung

Philips

Philips SH71/50 Bedienungsanleitung

Philips

Philips OccuSwitch Classic LRL2390 Installationsanleitung

Philips

Philips 2G350A2H Bedienungsanleitung

Philips

Philips DLA71015 Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung

Philips dynalite DUS704W Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken