Philips EasyAir SNS300 Bedienungsanleitung

Design-in Guide

Single, compact, cost-effective

luminaire control

Philips EasyAir SNS300

Sensors

EasyAir

SNS300

August 2019

2Design-in Guide - EasyAir SNS300 April 2019

Contents

Introduction to this guide 3

More information or support 3

Warnings and instructions 4

Introduction of EasyAir SNS300 5

Product characteristics 6

EasyAir SNS300 overview 6

NFC antenna 6

RF antenna 6

Infared (IR) receiver 6

Motion detector 7

Light sensor 9

LED indicator 9

Lighting control 9

Limited functions of

Philips Field Apps 10

Mechanical design-in 11

Mounting to a luminaire 11

Wiring diagram with Philips Xitanium SR LED driver 12

Labeling for field installation and commissioning 14

Recommendations to design a luminaire around

EasyAir SNS300 with good RF signal 15

Sensor position 15

Sensor spacing recommendations 16

Installing EasyAir SNS300 with ceiling

mount bracket (SNS300CMP) 17

EasyAir SNS300 with multiple Philips Xitanium

SR LED drivers (1:N application) 18

Contact details 19

Philips EasyAir SNS300 19

Disclaimer 20

August, 2019

3Design-in Guide - EasyAir SNS300 April 2019

Introduction to this guide

Thank you for choosing the Philips EasyAir SNS300.

In this guide, luminaire manufacturers will find the

information required to design this product into a

luminaire and configure it to suit specific

applications.

This design-in guide covers sensor functionality,

mechanical mounting and wiring details.

For sensor specifications, please see the datasheet

available at www.lighting.philips.co.uk/oem-emea/

products/connected-lighting.

More information or support

For further information or support, please consult

yourlocal Philips sales representative or visit

www.lighting.philips.co.uk/oem-emea/support/

technical-downloads.

August, 2019

4Design-in Guide - EasyAir SNS300 April 2019

Warnings and instructions

• EasyAir SNS300 must be used only with a Philips

Xitanium SR LED driver.

• Do not apply mains power directly to the sensor.

• Do not cover the sensor during operation or mount

the sensor recessed.

• External infrared light source in the space might

have influence on occupancy detection.

• Incorrect location of sensor (e.g., outside the view

angle of the occupancy sensor) will result in

occupancy detection not functioning correctly.

• Make sure the sensor, especially the occupancy

detection lens, is protected from damage during

shipment and handling.

• The application area of EasyAir SNS300 is designed

for a typical indoor environment (open/private

offices, conference rooms, classrooms, corridors,

etc.) in normally heated and ventilated areas.

EasyAir SNS300 has no protection against

aggressive chemicals or water.

• Make sure the the EasyAir SNS300 RF antenna is

not covered by metal for proper RF communication.

August, 2019

5Design-in Guide - EasyAir SNS300 April 2019

Introduction of EasyAir SNS300

EasyAir SNS300 for networks is based on Zigbee

technology for use in wireless systems for indoor

connected lighting. It provides a simple solution to

actively manage and control energy usage, while

remotely adjusting light settings and determining

service needs. With the added Zigbee functionality,

EasyAir SNS300 can now be an integral part of

networks also based on the Zigbee standard.

A program is under development by Philips to qualify

third-party network systems for use with EasyAir

SNS300.

EasyAir SNS300 is renowned for its compact size and

ability to easily integrate into luminaires. In addition,

the sensors are compatible with Philips Xitanium SR

LED drivers, eliminating the need for auxiliary devices

and alleviating time-consuming configuration issues.

The simple two-wire connection from driver to

sensor reduces design-in complexity and eliminates

additional components that add to overall costs.

Now, SNS300 can provide luminairespecific

information into networks for centralized control and

enable functionality such as energy monitoring,

scheduling and load shedding.

August, 2019

6Design-in Guide - EasyAir SNS300 April 2019

Product characteristics

EasyAir SNS300 overview

The Philips EasyAir SNS300 contains multiple

functions in one housing and uses two wires to

connect with an SR driver. (See wiring diagram in the

Mechanical designin section.)

Functions include:

EasyAir SNS300 is designed for a typical indoor

environment (open/private offices, conference rooms,

classrooms, corridors, etc.) in normally heated and

ventilated areas. EasyAir SNS300 has no protection

against aggressive chemicals or water. The sensor is

normally mounted to a luminaire and is optimized for

a sensor mounting height of 2.5m to 3m.

NFC antenna

Device model/version information and MAC address

can be read out using the Philips Field Apps (EasyAir

SNS300 NFC). NFC is the set of protocols that

enables electronic devices to establish radio

communication with each other by touching the

devices together or bringing them into proximity to a

distance of typically 1cm or less.

RF antenna

The RF antenna allows communication via RF

Infared (IR) receiver

• RF antenna

• NFC antenna

• Occupancy sensor (PIR)

• Light sensor

• Infrared receiver

• LED indicator

technology. It should not be covered by metal and

should be exposed to free air to ensure there is

sufficient range.

The infrared receiver serves as a communication

portal for the commissioning tools. Network settings

for an individual sensor can be reset with the Philips

Field Apps (IR).

Philips Field apps is available for free on Google

PlayStore. The user needs to download the app on an

Android phone, register and sign-in.

Once logged into the app, go to "EasyAir Office IR →

SNS200 → Maintenance → Reset Network Settings"

to reset the devices.

August, 2019

7Design-in Guide - EasyAir SNS300 April 2019

Motion detector

The occupancy sensor is a PIR (Passive Infrared)

sensor that detects movement with an X-Y

cross-area under an angle of X = 72° and Y = 86°. Two

types of movements are defined in NEMA WD7 as

follows:

• Major movement: movement of a person walking

into or through an area.

• Minor movement: movement of a person sitting at

an office desk reaching for a telephone, turning the

pages in a book, opening a file folder, picking up a

coffee cup, etc.

When installed in a typical office ceiling at H, the

sensor is sensitive to minor movements within X1 by

Y1 area. It will respond to minor movements down to

a few centimeters at the task area of a desk and is

sensitive to major movements within a range of X2

by Y2. The maximum recommended height to place

the sensor in the ceiling is 10ft/3m to assure

movement coverage and detection. The PIR sensor

reacts on movement by means of a temperature

difference, such as the human body temperature

versus its surrounding temperature. A car that just

starts its engine is not seen by the PIR nor does the

PIR see people sitting within the car or a forklift truck.

Therefore, it is recommended not to use EasyAir

SNS300 in outdoor, parking or industrial

applications. Please refer to the EasyAir SNS300

datasheet for coverage area details.

Figure 1. Motion detection area. H: ceiling height. Minor movement detection area: X1 by Y1. Major movement detection area: X2 by Y2.

August, 2019

8Design-in Guide - EasyAir SNS300 April 2019

Sensor view shield

The sensor comes with an occupancy view shield

that can be used to block the movement detection

by the sensor in a certain area. The shield comes

inverted. (See Figure 2.) This view shield can be

pulled out, flipped and inserted back in the sensor

and then rotated so the correct area is shielded off

from the detection area. If such shield is not needed

in the application, it can be easily pulled out from

the sensor or left inverted.

• Occupancy view shield

Figure 2. Sensor view shield.

August, 2019

9Design-in Guide - EasyAir SNS300 April 2019

Photocell

Window

Windowsill

eld of view

(= 0.7 x h)

Field of viewY (cm)

H (cm)

100

230

210

190

170

150

130

110

120 140 160 180 200 220 240 260 280

Light sensor

The light sensor is a photo diode that reads average

light level captured under an angle of approximately

40°. The intensity of the illuminance depends on the

amount of artificial and/or natural light supplied in the

office, as well as how this light is reflected toward

the ceiling/sensor. SNS300 sends the illuminance

signal to the gateway and the network lighting control

system controls the light accordingly.

The sensor should be installed with a minimum

distance of 0.6m to the window to avoid the sensor

looking outside. When the sensor is mounted too

close to the window it will look partly outside. Sun

reflection from cars or snow can reflect directly into

the sensor. The sensor will then measure such high

illumination levels that it will drive the artificial light to

its minimal level or even switch off the artificial lights.

The optimum distance [Y] from the window to EasyAir

SNS300 can be obtained from Figure 4. This graph

shows the relation between the distance from the

window to the sensor [Y] and the height [H] of the

sensor (H, height of the sensor measured from ceiling

to bottom of window sill).

LED indicator

The product contains an LED indicator to help

comply with California Title 20 requirements. The

LED indicator is enabled by default. The behavior of

the LED is as follows:

Yellow LED on: vacancy & light sensor are functional.

Red LED on: motion is detected and hold time is not

expired yet.

Lighting control

Calibration and lighting control is done by the

coordinating network system.

Figure 3. Sensor placement.

Figure 4. Sensor mounting height from window sill (Y) vs.

sensor horizontal distance from window sill (H).

August, 2019

10 Design-in Guide - EasyAir SNS300 April 2019

Limited functions of

Philips Field Apps

The EasyAir SNS300 NFC App can be used to read

out model/version information of SNS300 and the

MAC address. The EasyAir SNS300 IR App can be

used to reset the network settings of individual

sensor.

Phone requirements: The EasyAir SNS300 app works

only on Android-based smartphones. Check the

EasyAir SNS300 website for the latest list of

compatible phones and their NFC reader locations.

The app can be downloaded from the Google Play

Store. This is a B2B app which requires

authentication with user ID and password. Please

appregistration/ to obtain a user id and password.

Please check the latest user’s manual at

www.lighting.philips.co.uk/oem-emea/products/

easy-to-integrate-wireless-sensors.html for

information on using the app with EasyAir SNS300.

August, 2019

Andere Handbücher für EasyAir SNS300

Inhaltsverzeichnis

Andere Philips Zubehör Handbücher

Philips

Philips HS85 Bedienungsanleitung

Philips

Philips LFH7177/00 Bedienungsanleitung

Philips

Philips CRP333 Bedienungsanleitung

Philips

Philips P-5611-B Bedienungsanleitung

Philips

Philips SPF1902 Bedienungsanleitung

Philips

Philips CRP136 Bedienungsanleitung

Philips

Philips AEA1000/00 Bedienungsanleitung

Philips

Philips CRP320 Bedienungsanleitung

Philips

Philips PR3110 Bedienungsanleitung

Philips

Philips Norelco 7100 series Bedienungsanleitung

Philips

Philips DLA71025 Bedienungsanleitung

Philips

Philips dynalite DUS360CR Bedienungsanleitung

Philips

Philips OccuSwitch Classic LRL2380 Installationsanleitung

Philips

Philips P-5794-B Bedienungsanleitung

Philips

Philips GC012 Bedienungsanleitung

Philips

Philips CRP357 Bedienungsanleitung

Philips

Philips SDW5003GN Bedienungsanleitung

Philips

Philips CRP311 Bedienungsanleitung

Philips

Philips HX8211 AirFloss Retail Bedienungsanleitung

Philips

Philips HF3510 Bedienungsanleitung

Philips

Philips CRP301 Bedienungsanleitung

Philips

Philips DLA63059 Bedienungsanleitung

Philips

Philips SJM2007 Bedienungsanleitung

Philips

Philips Home Power SPS1060N/17 Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung