Philips EasySense SNS210 MC Bedienungsanleitung

Single, compact, cost-effective

luminaire control

Philips EasySense SNS210 MC

July 2020

Design-in Guide

Sensors

EasyAir

SNS210

Sensors

EasySense

SNS210 MC

2Design-in Guide - EasySense SNS210 MC July 2020

Contents

Introduction to this guide 3

More information or support 3

Warnings and instructions 4

Introduction of EasySense SNS210 MC 5

Product characteristics 6

EasySense SNS210 MC overview 6

Zigbee and Bluetooth Low Energy 6

Motion detector 7

Sensor view shield 8

Light sensor 9

LED indicator 9

Mechanical design-in 10

Wire strip length 10

Wire insertion 10

Wire separation from the connector 10

Wiring Information 10

Wire distance for remote mounting 11

Luminaire-to-luminaire distance 11

Recommendations to design-in around EasySense

SNS210 MC with good RF signal 11

Recommendations to design-in a luminaire

around EasySense SNS210 MC with good RF signal 11

Mounting to a luminaire 12

Mounting in a bracket (SMB-50) 13

Installing EasySense SNS210 MC with ceiling

mount bracket (SNS210 MCCMP) 14

Installer Label Instructions 15

EasySense SNS210 MC with multiple Philips Xitanium

SR LED drivers (1:N application) 16

Luminaire Production Test 17

FAQ 18

Contact details 20

Philips EasySense SNS210 MC 20

Disclaimer 21

3Design-in Guide - EasySense SNS210 MC July 2020

Introduction to this guide

Thank you for choosing Philips EasySense SNS210 MC. In

this guide luminaire manufacturers will find the information

required to design this product into a luminaire and

configure it to suit specific applications. This design-in

guide covers sensor functionality, mechanical mounting,

wiring details, configuration and commissioning (grouping)

method, application notes and frequently asked questions.

More information or support

For further information or support, please consult your

local Signify sales representative.

Philips EasySense SNS210 MC

4Design-in Guide - EasySense SNS210 MC July 2020

Warnings and instructions

• EasySense SNS210 MC must be used with Philips

Xitanium SR LED drivers.

• Do not apply mains power directly to the sensor.

• Do not cover the sensor during operation or mount the

sensor internal to the luminaire.

• External infrared light source in the space might have

influence on occupancy detection.

• Incorrect location of sensor (e.g., with setting up of

multiple SNS210 devices into a single network or a group

with addition of qualified wireless switches obstructions

in viewing angle) will result in incorrect functioning of

occupancy detection.

• Faulty settings of the sensor might result in undefined

startup.

• Make sure the sensor, especially the occupancy detection

lens, is protected from damage during shipment and

handling.

• The application area of EasySense SNS210 MC is

designed for a typical indoor environment (open/private

offices, conference rooms, classrooms, corridors, etc.) in

normally heated and ventilated areas. EasySense SNS210

MC has no protection against aggressive chemicals or

water.

• Make sure the the EasySense SNS210 MC Zigbee/

Bluetooth antenna is not covered by metal for proper RF

communication.

5Design-in Guide - EasySense SNS210 MC July 2020

Introduction to EasySense SNS210 MC

The Philips EasySense SNS210 MC is the ideal solution for

per-luminaire control of smart luminaires. It combines

occupancy sensing, daylight harvesting and task tuning in a

single, compact package for easy OEM luminaire assembly.

EasySense SNS210 MC operates with the established

Xitanium SR LED driver standard to make a simple two-

wire connection between sensor and driver, thus

eliminating the need for multiple components and auxiliary

devices. The result is a cost-effective and easy-to-

design-in solution ideal for energy-savings. An intuitive

MasterConnect app makes commissioning and

configuration during and after installation fast and easy.

EasySense SNS210 MC enables grouping allows scene

setting on a wireless switch (e.g., presentation mode for a

conference room) as well as occupancy sharing (i.e.,

luminaires within a group can be programmed to remain at

prescribed light levels so long as occupancy is detected

anywhere in the group).

For more details on specification and ordering codes,

please refer to the SNS210 MC datasheet on the technical

downloads page.

6Design-in Guide - EasySense SNS210 MC July 2020

Product characteristics

EasySense SNS210 MC overview

EasySense SNS210 MC contains multiple functions in one

housing and uses two wires to connect with an SR driver.

(See wiring diagram in the Mechanical design-in section.)

Functions include:

• Zigbee/Bluetooth

LE antenna

• Occupancy sensor (PIR)

• Light sensor

• LED indicator

EasySense SNS210 MC is designed for a typical indoor

environment (open/private offices, conference rooms,

classrooms, corridors, etc.) in normally heated and

ventilated areas. The sensor is normally mounted to a

luminaire and is optimized for a sensor mounting height of

2.5 m to 3 m.

Zigbee and Bluetooth Low Energy (BLE)

The Zigbee-BLE antenna should not be covered by metal

and should be exposed to free air to ensure there is

sufficient range.

For more information on mechanical design in of the

sensor, please refer the section on page 11.

7Design-in Guide - EasySense SNS210 MC July 2020

Motion detector

The occupancy sensor is a PIR (Passive Infrared) sensor

that detects movement with an X-Y cross-area under an

angle of X = 62° and Y = 84°. Two types of movements

are defined as follows:

• Major movement: movement of a person walking into or

through an area.

• Minor movement: movement of a person sitting at an

office desk reaching for a telephone, turning the pages in

a book, opening a file folder, picking up a coffee cup, etc.

When installed in a typical office ceiling at height, the

sensor is sensitive to minor movements within X1 by Y1

area. It will respond to minor movements down to a few

centimeters at the task area of a desk and is sensitive

to major movements within a range of X2 by Y2. The

directions X1, X2 are parallel to direction X; likewise for Y1,

Y2 being parallel to Y. The maximum recommended height

to place the sensor in the ceiling is 3 m to assure

movement coverage and detection. The PIR sensor reacts

on movement by means of a temperature difference, such

as the human body temperature versus its surrounding

temperature e.g. people. People sitting behind a

transparent shield or glass window are not seen by PIR

sensor of SNS210. Please refer to the table below for

coverage area details.

Figure 1. Motion detection area. H: ceiling height. Minor movement detection area: X1 by Y1. Major movement detection area: X2 by Y2.

Minor movement Major movement

Height X1 Y1 X2 Y2

2.4m 1.9 2.9 2.9 4.3

3.0m 2.4 3.6 3.6 5.4

8Design-in Guide - EasySense SNS210 MC July 2020

Sensor view shield

The sensor comes with an occupancy view shield that can

be used to block the movement detection by the sensor in

a certain area. The shield comes inverted. (See Figure 2.)

This view shield can be pulled out, flipped and inserted

back in the sensor and then rotated so the correct area is

shielded off from the detection area. If such shield is not

needed in the application, it can be easily pulled out from

the sensor or left as in the original position.

To prevent false triggers, the EasySense SNS210 MC must

be mounted more than 2 m away from air vents in all

directions, see figures below:

> 2m

Luminaire

> 2m

• Occupancy view shield

Figure 2. Sensor view shield.

9Design-in Guide - EasySense SNS210 MC July 2020

Photocell

Window

Windowsill

eld of view

(= 0.7 x h)

Field of viewY (cm)

H (cm)

100

120

150 200

300

250

Light sensor

The light sensor is a photo diode that reads the average light

level captured under an angle of approximately 40°. This

level depends on the amount of artificial and/or natural

light supplied in the office, as well as how this light is

reflected toward the ceiling/sensor. The EasySense SNS210

MC converts the illuminance signal into ON/OFF or dimming

commands to the Philips Xitanium SR LED driver in order to

maintain a constant light level on the desk.

The sensor should be installed with a minimum distance of

0.6 m to the window to avoid the sensor looking outside.

When the sensor is mounted too close to the window it will

look partly outside. Sun reflection from cars or snow can

reflect directly into the sensor. The sensor will then measure

such high illumination levels that it will drive the artificial

light to its minimal level or even switch off the artificial

lights. The optimum distance [Y] from the window to

EasySense SNS210 MC can be obtained from Figure 4. This

graph shows the relation between the distance from the

window to the sensor [Y] and the height [H] of the sensor (H,

height of the sensor measured from ceiling to bottom of

window sill).

LED indicator

The product contains a LED indicator. This is enabled by

default, and it can be disabled through the app. The

behavior of the LED is as follows:

Yellow LED on: = vacancy & light sensor are functional.

Red LED on: = motion is detected and hold time is not

expired yet.

Figure 3. Sensor placement.

Figure 4. Sensor mounting height from window sill (Y) vs. sensor horizontal distance from

window sill (H).

10 Design-in Guide - EasySense SNS210 MC July 2020

Mechanical design-in

Wiring Information

Applicable wires

Conductor size: solid 0.2 - 0.75 mm2

Conductor size: fine-stranded 0.2 - 0.75 mm2

Conductor size: fine-stranded 0.25 - 0.34 mm2

(with insulated formule)

Conductor size: fine-stranded 0.25 - 0.34 mm2

(with insulated formule)

AWG 24 - 18

Strip length 7 - 9 mm / 0.28 - 0.35 in

Note: Stranded wires without ferrule should be soldered

Strip length

8.0 ± 0.5 mm

Conductor

[ Conductor: Bare Copper / Strand wire ]

Insulation

5°~7° Angle Max

Insertion

[ Inserting solid conductors via push-in terminal ]

2. Pull-out

1. Push

Wire strip length

Wire insertion

Wire separation from the connector

Inserting solid conductors via push-in terminal

Andere Handbücher für EasySense SNS210 MC

Inhaltsverzeichnis

Andere Philips Zubehör Handbücher

Philips

Philips HF3470 Bedienungsanleitung

Philips

Philips SAC2520W/10 Bedienungsanleitung

Philips

Philips DLA7575H Bedienungsanleitung

Philips

Philips 15719-8 Bedienungsanleitung

Philips

Philips HP3614 Bedienungsanleitung

Philips

Philips CRP148 Bedienungsanleitung

Philips

Philips RI9125/24 Bedienungsanleitung

Philips

Philips SCF302/13 Bedienungsanleitung

Philips

Philips CRP323 Bedienungsanleitung

Philips

Philips 2G350A2H Bedienungsanleitung

Philips

Philips 63059CM Original Betriebsanleitung

Philips

Philips CRP349 Bedienungsanleitung

Philips

Philips LFH7177/03 Bedienungsanleitung

Philips

Philips CRP139 Bedienungsanleitung

Philips

Philips SWA3301W Bedienungsanleitung

Philips

Philips Somneo Sleep and Wake-Up Light Programmierhandbuch

Philips

Philips HF3485/01 Bedienungsanleitung

Philips

Philips Sonicare HX3806 Bedienungsanleitung

Philips

Philips DLA81820H Bedienungsanleitung

Philips

Philips SVC2230/10 Bedienungsanleitung

Philips

Philips US2-PH63020 Bedienungsanleitung

Philips

Philips CD74RW/121 Bedienungsanleitung

Philips

Philips SVC2235/10 Bedienungsanleitung

Philips

Philips AEA1000/37 Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung