Philips Dynalite DDBC516FR Bedienungsanleitung

features

To reduce the risk of fire or electric shock, do not expose

this device to rain or moisture. Do not energise unless the

front cover is in place. This device must be earthed.

Installation, programming and maintenance must be

carried out by qualified personnel.

Single Phase Supply - 1 phase at 0.15A

5 x Feed thru Outputs Rated at 16A

Power outputs are Latching Relays

Manual Overrides for each channel

Powerful Internal PLC - Custom scripts can be written to

provide process control based on conditional logic

Dry Contact Interface - An Auxiliary dry contact interface is

provided. The factory settings will cause this input to transmit

network identification information

Many Control Options - Control of this device can be via a

combination of methods, eg. serial control port, relay

contacts, push button wall stations, infrared receivers and

time clocks

Simple Installation - DIN Rail mount facilitates installation.

All connection terminals are accessible without disassembly

Warning –This device is a class A product. In a domestic environment this

product may cause radio interference, in which case the user may be required to

take adequate measures.

Read Instructions –We recommend that you read this Instruction Manual prior

to commencement of installation.

Manual Override Switches - These switches do not provide permanent

isolation. Isolate at the supply before performing work on load circuits.

Special Programming –This device will only operate in basic modes unless

programmed via a computer. If programming is required, contact your local

agent for details. Once the data cable is connected to the devices, the factory

default settings will allow any control panel to operate all channels in all

controllers.

Power Sources –This device should only be operated from the type of supply

specified on the front cover. This device must be earthed.

Feed Thru Output Circuits –The load on a circuit should not exceed the

specified capacity of 16A. Loads should be calculated to ensure that the overall

maximum capacity of 80A is not exceeded. This device should be fed via a HRC

fuse or MCB. Output circuits are suitable for Single Phase or Three Phase Star

(with Neutral) only, Delta wiring is not supported.

Mounting Location –Install in a dry, well-ventilated location. Controllers may

emit some mechanical noise. Take this into account when deciding the mounting

location.

Data Cable –Use screened, stranded RS485 data cable with three twisted pairs.

Segregate from mains cables by 300mm minimum. Connect devices in a ‘daisy

chain’. A data cable that is connected to an energised device is live. Do not cut

or terminate live data cables.

DDBC516FR

5 x 16A relay & Open Protocol Controller

Installation Manual

………

electrical diagram

installation steps

product specifications

1. Mount the device on a DIN rail inside an approved enclosure.

2. Calculate loads to ensure any channels are not overloaded, then connect loads to the output channels. The maximum

loading of this device is as follows:

Maximum Channel Load: 16A 230V AC

Total Box Load: 80A

Connect supply and load cables to each channel. Note that this device must have an individual supply circuit for each

channel. The supply circuits can be on any phase. Note that loads must have a Neutral (1 Phase or 3 Phase Star), Delta

wiring is not supported.

3. 5 x Control Outputs, each selectable to;

- DALI broadcast: max 10 DALI loads per channel.

- DALI addressed: max 10 DALI loads per channel.

- 1-10V: max 10mA Sink or Source per channel.

- DSI: max 10 DSI loads per channel.

4. Connect a single phase 0.15A feed to the control circuit supply terminals. This device must be earthed.

5. Connect data cables to the device as per diagrams below.

6. If the Auxiliary input is to be used, connect a dry contact device in between the AUX and GND terminals. Keep cable runs

between the device and the dry contacts under two metres. The function of the Auxiliary input will need to be programmed

at the time of commissioning.

Control Supply: 230V ±14% 50/60Hz single phase at 0.15A

Load Outputs: 5 x Feed Thru Outputs at 16A per channel, max total box load is 80A

Wiring topology: 1 Phase & Neutral and 3 Phase & Neutral Star. Delta not supported

5 x Open protocol, each selectable to DALI address, DALI Broadcast, 1-10V or DSI

Switching Device: Relay –50A 230V AC resistive (5000W Lighting Load rated)

Supply Terminals: 1 x Phase, 1 x Neutral 1 x Earth, up to 1 x 4mm2cable per terminal

Load Terminals: IN, OUT for each channel, up to 1 x 4mm2cable per terminal

IO: 1 x RS485 DyNet serial port

1 x AUX programmable dry contact input

DyNet DC Supply: 200mA (capacity for approx 5 Panels)

Presets: 170 170

Programmable Logic: 8 Tasks, most UPAN mnemonics supported

Compliance: CE, C-Tick

Ambient Temperature: 50C max.

Construction: Polycarbonate plastic DIN rail mount

Dimensions: Height 93mm x Width 211mm x Depth 75mm

Weight: 0.8Kg

DDBC516FR-DALI Rev B Specifications subject to change without notice

Dynalite manufactured by WMGD Pty Ltd (ABN 33 097 246 921) Unit 6, 691 Gardeners Road Mascot NSW 2020 Australia Tel: +61 2 8338 9899 Fax: +61 2 8338 9333

E-Mail: dynalite.inf[email protected]om Web: Philips.com/dynalite

Andere Philips Controller Handbücher

Philips

Philips Lightolier Controls Sunrise Whispurr Bedienungsanleitung

Philips

Philips Vaya Touch Controller Bedienungsanleitung

Philips

Philips Strand Lighting Sixer Bedienungsanleitung

Philips

Philips Dynalite DDRC810DT-GL Bedienungsanleitung

Philips

Philips dynalite DDBC120-DALI Bedienungsanleitung

Philips

Philips Dynalite DBC1205 Bedienungsanleitung

Philips

Philips dynalite DBC1210 Bedienungsanleitung

Philips

Philips iPlayer 3 Bedienungsanleitung

Philips

Philips PTN3501 Bedienungsanleitung

Philips

Philips Dynalite DMAL120F Bedienungsanleitung

Philips

Philips CoralCare Bedienungsanleitung

Philips

Philips Dynalite Revolution DR2PE Bedienungsanleitung

Philips

Philips CoralCare Montageanleitung

Philips

Philips LFH 2305 Bedienungsanleitung

Philips

Philips ColorDial Pro Bedienungsanleitung

Philips

Philips 9890 000 0268 Series Bedienungsanleitung

Philips

Philips AntumbraButton Bedienungsanleitung

Philips

Philips SC1500 Bedienungsanleitung

Philips

Philips dynalite DALI DDBC120-DALI Bedienungsanleitung

Philips

Philips Dynalite DDLE801 Bedienungsanleitung

Philips

Philips Light System Manager Bedienungsanleitung

Philips

Philips Dynalite Revolution Series Bedienungsanleitung

Philips

Philips iPlayer 3 Bedienungsanleitung

Philips

Philips MSX VU 0005 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch