Philips SLV5405 Bedienungsanleitung
Wireless TV Link
User Manual
SLV5405
WIRELESS TV LINK RECEIVER
1
2
4
3
5
6
7
8
A
3
EN
Contents
Page
Overview 4
Control and display elements 4
Your Wireless TV Link 5
Safety 5
Installation 6
Operation 6
Enjoy your Wireless TV Link 6
Troubleshooting 8
Information 10
Health and safety 10
Maintenance and service 10
Recycling and disposal 10
Warranty 11
Glossary 11
4
EN Overview
Control and display elements
A Receiver
1 On/off switch
2 Power light
> red: standby
> green: on
> blinking: remote control signalling
3 Source selector buttons (+/-)
> in combination with the SLV5400 transmitter
4 Integrated remote control blaster light
5 Antenna
6 Wireless channel selection switch
7 SCART port for TV2
8 Power input connector (DC 12V)
5
EN
Your Wireless TV Link
You can say good-bye to wires. With your Wireless TV
Link receiver you can now wirelessly connect a third TV
and choose between four devices to watch on your third
TV.
Safety
• Read the instructions in this manual carefully before
you connect, install and use the product.
• Keep this manual for future reference.
• The product is for indoor use only.
• Do not use the product close to water.
• Do not expose the product to extreme heat.
• In case of technical difficulties, do not open the
product. Bring it to your Philips dealer.
• Do not cover the product.
• Connect the power adapters only to a
220-240 V AC/50 Hz power supply.
• The product can cause interference to other
equipment. Check if any equipment near the product
can be affected before you start using it.
6
EN Installation
Remove interference on TV3
1 Find the CHANNEL switch on the transmitter.
2 Check the setting of the CHANNEL switch.
3 Find the CHANNEL switch on the receiver (A).
4 Set the CHANNEL switch to the same number as
on the transmitter.
Operation
Enjoy your Wireless TV Link
For basic installation, see
the quick start guide that
came with your Wireless
TV Link.
L
Channel
DC 12V
1 2 3 4
R
CHANNEL
1
2
3
4
Make sure to set the CHANNEL
switch on both the original and the new
receiver.
For basic installation, see
the quick start guide that
came with your Wireless
TV Link.
7
EN
Operation
Watch a cable TV program on TV3
1 Switch on the transmitter.
2 Switch on the VCR or DVD recorder.
3 Take the remote control of the VCR or DVD
recorder with you.
4 Go to TV3.
5 Switch on TV3.
6 Switch on the receiver (A).
7 Press +or -on the receiver (A) to select the VCR or
DVD recorder;
or: press 4on the remote control.
8 Select the channel on the VCR or DVD recorder
with its remote control.
Your VCR or DVD recorder needs to
be connected to the transmitter (A) of
the Wireless TV Link and connected to
the Cable-TV signal.
STANDBY SELECT
SLV5400WIRELESS TV LINK TRANSMITTER
WIRELESS TV LINK RECEIVER
Turn off the auto standby mode when
you use the VCR or DVD recorder to
watch a cable tv program. Refer to the
user manual of the VCR or DVD
recorder.
If the VCR or DVD recorder records a
television program, you watch the
recorded channel.
8
EN Troubleshooting
Problem Tip
No image or wrong
image on TV3 • Make sure SCART cables are
firmly inserted.
• Make sure the receiver (A) is
connected to TV3.
• Make sure both receiver (A) and
transmitter are switched on.
• Make sure the video source is
switched on.
• Make sure the correct SCART
input on TV3 is selected.
• Select the correct video source
with +/- on the receiver (A).
> In combination with the
SLV5400 transmitter.
• If the video source gives proper
image on TV1:
Make sure the video source gives
video signal in CVBS mode. See
its user manual
• Change the wireless channel that
is used for communication. See
page 6.
• The receiver (A) is out of range
of the transmitter. The number
of walls and ceilings in between
the receiver (A) and transmitter
restrict the distance.
Interference in the
image on TV3 •
Slightly change the position of the
receiver (A) or the transmitter.
• Change the wireless channel that
is used for communication. See
page 6.
• The receiver (A) is out of range
of the transmitter. The number
of walls and ceilings in between
the receiver (A) and transmitter
restrict the distance.
9
EN
Troubleshooting
Problem Tip
The video sources
do not respond to
the remote
controlcommands
from TV3
• Point the remote control directly
to the receiver (A).
• Replace the batteries of the
remote controls with new ones.
• Install the remote control blaster
cord. See the user manual of the
Wireless TV Link.
• The maximum operating distance
of the remote control is 5 m.
The image of the
video source dis-
appears on TV3
• Turn off the auto standby mode
of the video source. See its user
manual.
• Follow the instructions to recon-
nect the video sources. See the
quick start guide.
Buzzing sound
when you use the
remote control.
• Slightly change the position of the
receiver or the transmitter until
the buzzing sound stops.
• Sometimes it is not possible to
solve the problem.
Black and white
image with S-VHS
VCR.
• Check if the SCART connector of
the S-VHS VCR gives signal in
CVBS. See its user manual.
10
EN Information
Health and safety
The product transmits and receives radio waves when it
is switched on. The product complies with the standards
that are defined for it.
The quality of the image can be influenced by the use of
microwave ovens. Other wireless systems (Bluetooth,
wireless networks etc.) can also have influence on the
quality of the image.
The product is based on RF technology. Therefore the
product can suffer from the same kinds of interference
as GSMs, portable radios and other RF-based products.
Maintenance and service
If your product is defective and needs repair, but your
warranty period has expired, you can consult our
specialists (see the rear page)
Recycling and disposal
All redundant packaging material has been omitted. Your
set consists of materials that can be recycled if
disassembled by a specialized company. Please observe
the local regulations regarding the disposal of packaging
materials, batteries and old equipment.
Disposal of your old product
Your product is designed and manufactured with high
quality materials and components, which can be recycled
and reused.
When this crossed-out wheeled bin symbol is attached
to a product it means the product is covered by the
European Directive 2002/96/EC.
Please inform yourself about the local separate collection
system for electrical and electronic products.
Please act according to your local rules and do not
dispose of your old products with your normal
household waste. The correct disposal of your old
product will help prevent potential negative
consequences for the environment and human health.
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Philips Empfänger Handbücher
Philips
Philips MX735 Bedienungsanleitung
Philips
Philips HTS5000W/51 Bedienungsanleitung
Philips
Philips FR 731 Bedienungsanleitung
Philips
Philips LX600 Bedienungsanleitung
Philips
Philips FR751/01 Bedienungsanleitung
Philips
Philips FR 732 Bedienungsanleitung
Philips
Philips pA 22AH572 Bedienungs- und Montageanleitung
Philips
Philips AE 3650 Bedienungsanleitung
Philips
Philips LX710 Bedienungsanleitung
Philips
Philips DSX6073/03A Bedienungsanleitung
Philips
Philips HTS6500 - DivX Ultra Home Theater System Bedienungsanleitung
Philips
Philips DSR 2010 Bedienungsanleitung
Philips
Philips DSR2020 Bedienungsanleitung
Philips
Philips MX2600/55 Bedienungsanleitung
Philips
Philips HTR5000 Bedienungsanleitung
Philips
Philips FR 731 Bedienungsanleitung
Philips
Philips STU 904 Bedienungsanleitung
Philips
Philips DTR200/00 Bedienungsanleitung
Philips
Philips DTR1000/00 Bedienungsanleitung
Philips
Philips STU330A Bedienungsanleitung
