Philips FC8700 Handbuch

FC8710

FC8700

1 2 3

3 4 5

6 7 8 9

10 11 12

100 cm 30 cm

80 cm

14 15 16 17

18 19

20 21

FC8710

1516

9 10

2425

FC8710, FC8700

ENGLISH 8

DEUTSCH 17

ESPAÑOL 26

FRANÇAIS 35

ITALIANO 44

NEDERLANDS 53

PORTUGUÊS 62

Introduction

Congratulations on your purchase and welcome to Philips! To fully benet from the support that

Philips offers, register your product at www.philips.com/welcome.

Your robot (Fig. 1)

1 Top cover

2 Handle of dust container lid

3 Dust container lid

4 Filter

5 Dust container

6 Fan

7 Bumper

8 On/off button (switches robot on or to standby)

9 Display

10 Power switch (switches robot on or off)

11 Front wheel

12 Side brush shafts

13 Drop-off sensors

14 Wheels

15 Battery cavity

16 Suction opening

17 Rechargeable battery

18 Battery cavity cover

19 Screws

20 Side brushes

21 Battery holder

22 Remote control (FC8710)

23 Docking station

24 Adapter

25 Small plug

Display and remote control

Display

1 Warning indicator (Fig. 2)

2 On/off indicator

3 Dust container full indicator

Remote control (FC8710)

1 Navigation buttons and on/off (Fig. 3)

2 Docking button

3 Cleaning time button

4 Cleaning mode buttons

How your robot works

What your robot cleans

This robot is equipped with features that make it a suitable cleaner to help you clean the oors in

your home. The robot is especially suitable for cleaning hard oors, such as wooden, tiled or

linoleum oors. It may experience problems cleaning soft oors, such as carpet or rugs. If you use

the robot on a carpet or rug, please stay close by the rst time to see if the robot can deal with this

type of oor. The robot also needs supervision when you use it on black and shiny hard oors.

ENGLISH

How your robot cleans

Cleaning system

The robot has a 2-stage cleaning system to clean your oors efciently.

- The two side brushes help the robot clean in corners and along walls.They also help to remove

dirt loose from the oor and move it towards the suction opening (Fig. 4).

- The suction power of the robot picks up loose dirt and transports it through the suction

opening into the dust container (Fig. 5).

Cleaning patterns

In its auto cleaning mode, the robot uses an automatic sequence of cleaning patterns to clean each

area of the room optimally.The cleaning patterns it uses are:

1 Z-pattern or zigzag pattern

2 Random pattern

3 Wall-following pattern

4 Spiral pattern

During auto cleaning, the robot uses these patterns in a xed sequence:

1 Z-pattern (Fig. 6)

2 Random pattern (Fig. 7)

3 Wall-following pattern (Fig. 8)

4 Spiral pattern (Fig. 9)

When the robot has completed this sequence of patterns, it starts moving in Z-pattern again.

The robot continues to use this sequence of patterns to clean the room until the rechargeable

battery is empty, or until it is switched off manually.

Note:You can also select each mode individually by pressing the appropriate button on the remote

control (FC8710). For more details, see chapter ‘Using your robot’, section ‘Cleaning modes’.

How your robot avoids height differences

- The robot has three drop-off sensors in its bottom. It uses these drop-off sensors to detect and

avoid height differences such as staircases (Fig. 10).

Note: It is normal for the robot to move slightly over the edge of a height difference, as its front drop-off

sensor is located behind the bumper.

Caution: In some cases, the drop-off sensors may not detect a staircase or other height

difference in time. Therefore monitor the robot carefully the rst few times you use it,

and when you operate it near a staircase or another height difference.

Before rst use

Mounting the side brushes

1 Unpack the side brushes and place the robot upside down on a table or on the oor.

2 Push the side brushes onto the shafts on the bottom of the robot (Fig. 11).

Note: Make sure you attach the side brushes properly. Press them onto the shaft until you hear them

lock into position with a click.

Removing the protection tag from the remote control

The remote control (FC8710) works on a CR2025 coin-shaped battery.This battery is protected

with a protection tag that has to be removed before use.

1 Pull the battery protection tag out of the battery compartment of the remote

control (Fig. 12).

,Now the remote control is ready for use.

ENGLISH 7

Preparing for use

Installing the docking station

1 Insert the small plug of the adapter into the socket on the docking station (1) and insert the

adapter into the wall socket (2). The display of the docking station lights up (Fig. 13).

2 Place the docking station on a horizontal, level oor against the wall (Fig. 14).

Note: Make sure that there are no obstacles or height differences 80cm in front, 30 cm to the right and

100 cm to the left of the docking station.

Charging

When charging for the rst time and when the rechargeable battery of the robot is empty,

the charging time is four hours.

Your robot can be charged in two ways:

- On the docking station, either manually or automatically during use;

- By connecting the robot directly to the mains

Note:When the rechargeable battery is fully charged, your robot can clean for up to 100 minutes.

Charging on the docking station

1 Place the robot on the plugged-in docking station (Fig. 15).

2 Press the power switch to switch on the robot (Fig. 16).

3 The on/off indicator on the display starts ashing (Fig. 17).

4 When the rechargeable battery is fully charged, the on/off indicator on the display stops

ashing (Fig. 18).

Charging automatically during use

1 When the robot has nished cleaning or when only 15% of the battery power remains,

it automatically returns to the docking station to recharge.When the robot returns to the

docking station, the on/off indicator ashes quickly (Fig. 19).

2 When the rechargeable battery is fully charged, the battery indicator on the display of the

robot stops ashing.

Note:The robot only returns to the docking station automatically when it started cleaning from the

docking station.

Charging directly from the mains

1 Insert the small plug of the adapter into the socket on the robot (1). Insert the adapter into a

wall socket (2) (Fig. 20).

2 Press the power switch to switch on the robot.

3 When the robot is connected to the mains correctly, the lon/off indicator starts ashing.

This indicates that the robot is charging.

4 When the rechargeable battery is fully charged, the on/off indicator of the robot stops

ashing.

Preparing the room for a cleaning run

- Before you start the robot on its cleaning run, make sure that you remove all loose and fragile

objects from the oor (Fig. 21).

ENGLISH8

Using your robot

Starting and stopping

1 Press the on/off button (Fig. 22).

- You can press the on/off button on the robot.

- You can also press the on/off button on the remote control (FC8710) (Fig. 23).

Tip: If you press the on/off button on the docking station while the robot is charging, the robot starts

cleaning as soon as the rechargeable battery is full (Fig. 24).

2 The on/off indicator starts ashing slowly and the robot starts cleaning (Fig. 25).

3 The robot cleans in auto-cleaning mode until its battery runs low. In auto cleaning mode.

It follows repeated sequences of Z-pattern, random, wall-following and spiral

movements (Fig. 26).

Note:To select an individual mode, press one of the mode buttons on the remote control (FC8710).

See section ‘Cleaning mode selection’ for more details.

4 When the battery runs low, the on/off indicator starts ashing quickly and the robot returns

to the docking station to charge (Fig. 19).

5 You can also press the on/off button to interrupt or stop the cleaning run. If you press the

on/off button again and there is still enough energy in the rechargeable battery,

the robot continues cleaning in the auto cleaning mode.

6 To make the robot return to the docking station before the rechargeable battery runs low,

press the docking button on the remote control (FC8710). (Fig. 27)

- The on/off indicator lights up and the robot returns to the docking station (Fig. 28).

Note: If you did not start the robot from the docking station, it does not return to the docking station

automatically when the rechargeable battery runs low. If there is still enough energy in the rechargeable

battery, you can press the docking button on the remote control to make the robot return to the docking

station. If the rechargeable battery is completely empty, you have to place the robot on the docking

station manually.

Cleaning mode selection (FC8710)

Next to the auto cleaning mode, this robot has four individual cleaning modes that can each be

activated by pressing the appropriate button on the remote control.

Z-pattern mode

- In Z-pattern mode, the robot cleans by making Z-shaped loops through the room to clean large

areas (Fig. 29)

Random mode

- In this mode, the robot cleans the room in a mixed pattern of straight and crisscross

movements. (Fig. 30)

Wall-following mode

- In this mode, the robot follows the walls of the room to give the area alongside the walls an

extra clean (Fig. 31).

Spiral mode

- In this mode, the robot makes a spiral movement with the fan at turbo speed to clean

a dirty area thoroughly (Fig. 32).

Manual driving (FC8710)

1 Use the arrow buttons above and below and to the left and right of the on/off button on the

remote control to navigate the robot through the room (Fig. 33).

ENGLISH 9

Note: Do not press the downward arrow when the robot is close to a height difference or a staircase.

Using the cleaning time buttons

- If you press the 24h button on the docking station, the docking station starts to count down the

24 hours until the next cleaning run. When the countdown is nished, the robot starts cleaning

until its battery runs low and then returns to the docking station automatically to

recharge (Fig. 34).

- Press the cleaning time button on the remote control (FC8710) to make the robot clean for 35

minutes. When the robot is nished, it returns to the docking station to recharge (Fig. 35).

Indicator signals and their meaning

The robot has a display with three indicators: the warning indicator, the on/off indicator and the dust

container full indicator. The table below explains the meaning of the signals these indicators give.

Indicator signal Meaning

The on/off indicator lights up continuously. The robot is cleaning.

The on/off indicator ashes. The rechargeable battery is low.

The dust container full indicator ashes. The dust container is full.

The warning indicator ashes. The robot was lifted while it was cleaning.

The bumper of the robot is stuck.

A wheel or side brush is stuck.

The top cover is not present or is not closed

properly.

The robot cannot nd the docking station.

Cleaning and maintenance

Emptying and cleaning the dust container

Empty and clean the dust container when the dust container full indicator ashes.

1 Remove the top cover (Fig. 36).

Note: Make sure the power switch is in ‘off ’ position.

2 Pull up the handle of the dust container lid and lift the dust container out of the dust

container compartment (Fig. 37).

Note:When you remove or reinsert the dust container, take care not to damage the blades of the motor fan.

3 Carefully lift the lid off the dust container and take out the lter (Fig. 38).

4 Shake the dust container over a dustbin to empty it. Clean the lter and the inside of the

dust container with a cloth or a toothbrush with soft bristles. Also clean the suction opening

in the bottom of the dust container (Fig. 39).

Caution: Do not clean the dust container and the lter with water or in the dishwasher.

5 Put the lter back into the dust container. Then place the lid on the dust container (Fig. 40).

6 Put the dust container back into the dust container compartment and put the top cover

back on the robot (Fig. 41).

ENGLISH10

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Philips Staubsauger Handbücher

Philips

Philips FC6168 Bedienungsanleitung

Philips

Philips FC9923 Bedienungsanleitung

Philips

Philips FC6161 Bedienungsanleitung

Philips

Philips 2000 series Bedienungsanleitung

Philips

Philips FC8138 Bedienungsanleitung

Philips

Philips FC6146 Bedienungsanleitung

Philips

Philips FC9089/01 Bedienungsanleitung

Philips

Philips Marathon Ultimate FC9934/07 Bedienungsanleitung

Philips

Philips FC8451 Bedienungsanleitung

Philips

Philips FC6723 Bedienungsanleitung

Philips

Philips SilentStar FC9306 Bedienungsanleitung

Philips

Philips FC8633 Bedienungsanleitung

Philips

Philips FC8199/01 Bedienungsanleitung

Philips

Philips AquaTrio FC7070 Bedienungsanleitung

Philips

Philips AquaTrio Cordless 7000 Series Bedienungsanleitung

Philips

Philips FC6052/11 Bedienungsanleitung

Philips

Philips Impact-plus FC 8388 Bedienungsanleitung

Philips

Philips FC6141 Bedienungsanleitung

Philips

Philips SpeedPro Aqua FC6728/01 Bedienungsanleitung

Philips

Philips SpeedPro Max Aqua FC6903 Bedienungsanleitung

Philips

Philips AquaTrio FC7070 Bedienungsanleitung

Philips

Philips FC6145 Bedienungsanleitung

Philips

Philips FC8732/01 Bedienungsanleitung

Philips

Philips 3000 series Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

Exido

Exido 240-114 Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung