Philips FC8796 Bedienungsanleitung

FC8796, FC8794,

FC8792

2022

6 7

11 12

English 6

Čeština 15

Latviešu 24

Magyar 33

Polski 42

Română 52

Slovenščina 61

Slovensky 70

Русский 79

Українська 89

Қазақша 98

English

Introduction

Congratulations on your purchase and welcome to Philips! To fully benefit from the support that

Philips offers, register your product at www.philips.com/welcome.

General description

1 Handle of dust container lid

2 Dust container lid

3 Filter unit

4 Dust container

5 Edge of top cover

6 Docking station sensor

7 Suction opening

8 Start/stop button

9 Side brushes

10 Shafts for mounting the side brushes

11 Front wheel

12 Suction opening

13 Side wheels

14 Sensors

15 Cover of the battery compartment

16 Mopping attachment (FC8796, FC8794)

17 Mopping pad (FC8796, FC8794)

18 Small plug

19 Adapter

20 Cleaning brush

21 Remote control

22 AA batteries for remote control

23 Docking station

Remote control

You can operate the robot with the remote control (Fig. 2). It has the following buttons:

1 Start/stop button

2 Navigation buttons

3 Docking button

4 Cleaning mode buttons

5 24-hour scheduler

How your robot works

What your robot cleans

This robot is equipped with features that make it a suitable cleaner to help you clean the floors in your

home.

The robot is especially suitable for cleaning hard floors, such as wooden, tiled or linoleum floors. It

may experience problems cleaning soft floors, such as carpet or rugs. If you use the robot on a carpet

6English

or rug, please stay close by the first time to see if the robot can deal with this type of floor. The robot

also needs supervision when you use it on very dark or shiny hard floors.

How your robot cleans

Cleaning system

The robot has a 3-stage cleaning system to clean your floors efficiently.

-The two side brushes help the robot clean in corners and along walls. They also help to remove dirt

from the floor and move it towards the suction opening (Fig. 3).

-The suction power of the robot picks up loose dirt and transports it through the suction opening

into the dust container (Fig. 4).

-Types FC8796 and FC8794 come with a mopping attachment that can be attached to the robot to

mop your hard floor.

Cleaning patterns

In its auto cleaning mode, the robot uses an automatic sequence of cleaning patterns to clean each

area of the room optimally. The cleaning patterns it uses are:

1 Random pattern (Fig. 5)

2 Wall-following pattern (Fig. 6)

3 Spot-cleaning pattern (Fig. 7)

In its auto cleaning mode, the robot uses these patterns in a fixed sequence: random pattern, wall-

following pattern, and spot-cleaning pattern.

When the robot has completed this sequence of patterns, it starts moving in random pattern again.

The robot continues to use this sequence of patterns to clean the room until the rechargeable battery

runs low, or until it is switched off manually.

Note: You can also select each mode individually by pressing the appropriate button on the remote

control (see 'Cleaning mode selection').

How your robot avoids height differences

The robot has five drop-off sensors in its bottom. It uses these drop-off sensors to detect and avoid

height differences such as staircases.

Note: It is normal for the robot to move slightly over the edge of a height difference, as its front drop-

off sensor is located behind the bumper.

Caution: In some cases, the drop-off sensors may not detect a staircase or other height difference

in time. Therefore monitor the robot carefully the first few times you use it, and when you operate

it near a staircase or another height difference. It is important that you clean the drop-off sensors

regularly to ensure the robot continues to detect height differences properly (see 'Cleaning the

robot').

Before first use

Mounting the side brushes

1Unpack the side brushes and place the robot upside down on a table or on the floor.

2Push the side brushes onto the shafts on the bottom of the robot (Fig. 8).

English

Note: Make sure you attach the side brushes properly. Press them onto the shaft until you hear

them lock into position with a click.

Placing the batteries in the remote control

The remote control works on two AA batteries.

1Push the tab (1) to unlock the battery compartment lid (2) and remove the battery compartment lid

(Fig. 9).

2Insert two AA batteries (Fig. 10).

Note: Make sure the + and - poles point in the right direction.

3To reattach the battery compartment lid, first insert the lug into the opening in the rim of the

compartment (1) and then push down the lid (2) until it locks with a click (Fig. 11). Now the remote

control is ready for use.

Preparing for use

Installing the docking station

1Insert the small plug of the adapter into the socket on the docking station (1) and insert the adapter

into the wall socket (2) (Fig. 12).

2Place the docking station on a horizontal, level floor against a wall.

Note: Make sure that there are no obstacles or height differences 150 cm in front, 30 cm to the right

and 100 cm to the left of the docking station (Fig. 13).

Charging

1Place the robot on the plugged-in docking station (Fig. 14).

2Press the start/stop button to activate the robot (Fig. 15).

3The start/stop button starts flashing (Fig. 16).

4When the rechargeable battery is fully charged, the start/stop button lights up continuously (Fig.

17).

Preparing the room for a cleaning run

-Before you start the robot on its cleaning run, make sure that you remove all loose and fragile

objects from the floor (Fig. 18).

-Remove all cables, wires and cords from the floor to prevent the robot from getting entangled in

them.

-If there is a rug with tassels in the room you want the robot to clean, fold the tassels under the rug

to prevent the robot from getting stuck on the tassels and to prevent the rug from getting damaged

(Fig. 19).

Using your robot

Starting and stopping

1Press the start/stop button on the remote control (Fig. 20).

2The start/stop button on the robot lights up continuously and the robot starts cleaning (Fig. 21).

8English

3The robot cleans in auto-cleaning mode until its battery runs low. In auto cleaning mode, it follows

repeated sequences of random, wall-following and spiral movements.

4When the battery runs low, the start/stop button starts flashing quickly and the robot starts

searching for the docking station to charge (Fig. 22).

5You can also press the start/stop button to interrupt or stop the cleaning run. If you press the

start/stop button again and there is still enough energy in the rechargeable battery, the robot

continues cleaning in the auto cleaning mode.

6To make the robot return to the docking station before the rechargeable battery runs low, press the

docking button on the remote control (Fig. 23).

7The start/stop button starts flashing and the robot returns to the docking station.

Note: If you did not start the robot from the docking station, it does not return to the docking

station automatically when the rechargeable battery runs low. If there is still enough energy in the

rechargeable battery, you can press the docking button on the remote control to make the robot

return to the docking station. If the rechargeable battery is completely empty, you have to place

the robot on the docking station manually.

Cleaning mode selection

This robot has three individual cleaning modes that can each be activated by pressing the appropriate

button on the remote control.

Random mode

In this mode, the robot cleans the room in a mixed pattern of straight and crisscross movements (Fig.

24).

Wall-following mode

In this mode, the robot follows the walls of the room to give the area alongside the walls an extra

clean (Fig. 25).

Spot-cleaning mode

In this mode, the robot moves randomly on a small area to clean this area thoroughly (Fig. 26).

Note: The manually selected modes are only active for a couple of minutes. After that, the robot

switches to auto-cleaning mode.

Manual driving

You can drive the robot manually with buttons on the remote control.

1Use the arrow buttons above and below and to the left and right of the start/stop button on the

remote control to navigate the robot through the room. (Fig. 27)

Note: Be careful when you drive the robot manually close to height differences and staircases.

Note: The vacuuming function and the side brushes only work when the robot is driven forward.

The left, right or back buttons are only for maneuvering the robot.

Using the 24-hour scheduler

The 24-hour scheduler can be activated with the remote control. Make sure the robot is in standby

mode and is not positioned on the docking station.

1Press the 24-hour scheduler button on the remote control to activate the 24-hour scheduler.

-When you activate the 24-hour scheduler, the display starts to flash briefly every few seconds.

English

-The robot will start a cleaning run 24 hours after you activated the 24-hour scheduler. It will

continue to start a cleaning run at the same time every 24 hours until you deactivate the

24-hour scheduler.

2To deactivate the 24-hour scheduler, press the 24-hour scheduler button. The display will light up

continuously to show the robot is in standby mode and the 24-hour scheduler is no longer active.

Mopping with the robot

Types FC8796 and FC8794 come with a mopping attachment and a mopping pad for wet cleaning of

hard floors.

Attaching the mopping pad

1Soak the mopping pad in water or wet the mopping pad under the tap. You can add a few drops of

a readily available floor cleaner that is suitable for your floor.

2Squeeze the mopping pad thoroughly to ensure it is only damp instead of wet.

3Attach the damp mopping pad to the mopping attachment by pushing the Velcro fasteners of the

mopping pad onto Velcro fasteners of the mopping attachment (Fig. 29).

4Insert the attachment lugs of the mopping attachment into the two attachment holes located just

behind the wheels. Then press down until you hear a click (Fig. 30).

Cleaning floors with the mopping attachment

Note: To clean hard floors with the mopping attachment, you have to start the robot from a point in

the room you wish to clean. You cannot start the robot from its docking station with the mopping pad

attached.

1Just press the start/stop button on the remote control to start the robot.

-The robot continues mopping until its battery runs low and the robot stops.

Note: Detach the mopping pad and the mopping attachment before you send the robot to the

docking station with the docking button on the remote control or before you place the robot on the

docking station manually.

Detaching the mopping attachment

1To detach the mopping attachment, press the tab (1) and pull up the mopping attachment to

remove it (2) (Fig. 31).

2Pull the mopping pad off the mopping attachment.

3To clean the mopping pad, wash it in the washing machine on a gentle cycle at a temperature of

60°C max.

Alarm signal

If the robot gets into trouble while cleaning (e.g., because a wheel jams or is no longer in contact with

the floor, or because a sensor can no longer detect the floor), you will hear a sound and the robot

stops. Press the start/stop button to switch the robot to standby mode and solve the problem that

causes the alarm signal, for instance by removing the obstacle that blocks the wheel, cleaning the

sensors, or picking up the robot and putting it down in a different place.

10 English

Andere Handbücher für FC8796

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Philips Staubsauger Handbücher

Philips

Philips Bruce FC6095/B Bedienungsanleitung

Philips

Philips HR6062/20 Bedienungsanleitung

Philips

Philips IMPACT PLUS Bedienungsanleitung

Philips

Philips FC6090 Bedienungsanleitung

Philips

Philips FC8334 Bedienungsanleitung

Philips

Philips FC8769 Bedienungsanleitung

Philips

Philips XW7110 Bedienungsanleitung

Philips

Philips HR6835 Bedienungsanleitung

Philips

Philips FC9210/01 Bedienungsanleitung

Philips

Philips FC8611 Bedienungsanleitung

Philips

Philips FC6055 Bedienungsanleitung

Philips

Philips FC8458 Bedienungsanleitung

Philips

Philips Performer Active FC8652/01 Bedienungsanleitung

Philips

Philips City Line FC8432 Bedienungsanleitung

Philips

Philips FC6049/01 Bedienungsanleitung

Philips

Philips FC9170/01 Bedienungsanleitung

Philips

Philips PowerPro Duo FC6162/02 Bedienungsanleitung

Philips

Philips HR8903/02 Bedienungsanleitung

Philips

Philips Bruce FC6093 Bedienungsanleitung

Philips

Philips FC8136/01 Bedienungsanleitung

Philips

Philips FC8440/01 Bedienungsanleitung

Philips

Philips PowerPro Aqua Bedienungsanleitung

Philips

Philips FC8257/01 Bedienungsanleitung

Philips

Philips Vision Duet Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

Exido

Exido 240-114 Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung