Phoenix Model Mustang P51 Bedienungsanleitung
We wish you many enjoyable flights with your plane and once again thank you for your choosing a Phoenix Model product
Instruction Manual
Wing span: 1550mm (61 inches)
Length: 1230mm (48.4 inches)
Weight: 3200 - 3600 gr. (6.4 - 7.2 lbs)
Engine: 60 two stroke - 91 four stroke
Radio: 6 channel 9 servos standar
g
Made in Vietnam
Instruction Manual Mustang P51
KIT CONTENTS: We have organized the parts as they come out of the box for better identification
during assembly. We recommend that you regroup the parts in the same manner. This will ensure you
have all of parts required before you begin assembly
AIR FRAME ASSEMBLIES
. (2) Wing halves with ailerons
. (1) Fuselage with canopy
. (1) Horizontal stabilizer with elevator halves
. (1) Vertical stabilizer with rudder
. (1) Cowling
. (1) Decal sheet
. (1) Instruction manual
MAIN GEAR ASSEMBLY
. (2) Main gear
. (2) 60mm diameter wheels
. (2) Connector gear
. (2) Metal rod 1.7mm x 30mm
. (2) Metal clevises M2
. (2) Metal connector
. (2) Servo tray
. (8) 2mm x 10mm screws
TAIL GEAR ASSEMBLY
. (1) Tail gear
. (1) 25mm diameter wheel
. (1) Wheel collar
. (2) Plastic clasp
. (2) 2mm x 10mm screws
ELEVATOR CONTROL SYSTEM
. (2) Set of Control horn
. (2) Metal clevises M2
. (2) Nylon snap keepper
. (2) 2mm bolt
RUDDER CONTROL SYSTEM
. (1) Set of Control horn
AILERON CONTROL SYSTEM
. (4) Set of control horn
. (4) Set metal clevis M3
. (1) Carbon fiber tube 15cm
MOTOR MOUNT ASSEMBLY
. (1) Engine mount
. (4) 4mm x 25mm screws
. (4) Flat Washer
. (4) Lock Washer
. (4) 4 mm Bolts
. (4) 3mm x 20mm screws
. (1) Metal rod 50cm
. (1) Nylon housing 35cm
. (1) Metal connector
FUEL TANK
. (1) Set Fuel tank
. (1) Foam
. (4) 110mm silicon tube
MISCELLANEOUS ITEMS
. (1) 40.5cm Dihedral
. (2) 25mm x 300mm trim tape
. (4) Wing screw
. (2) Nylon bushing
. (6) 2,6mm x 10mm screws
. (1) Spinner
. (1) Black trim tape
KIT CONTENTS
Instruction Manual Mustang P51
1 2 3
4 5 6
7 8 9
10 11 12
13 14 15
1. Installing the aileron and the flap servos
1
Remove the covering from the top of
the wing. Remove the covering from the aileron
servo box (at the bottom of the wing). Using the collar and prepare the thread
as a guide.
Insert the thread into the wing. Prepare the aileron servo. Tape the servo lead into the end of the
thread.
Pull the servo lead out. Secure the aileron servo. Remove the covering from the flap
servo box (at the bottom of the wing).
Using the collars and prepare the thread
as a guide. Insert the thread into the the wing. Tape the servo lead into the end of the
thread.
Pull the servo lead out. Using the masking tape, tape the servo
lead onto the top of the wing.
Make the same way to install the aileron
servo and the flap servo for the second
wing.
Thread Collar
Tape
Tape
Thread
Collar
Aileron Flap
2. Installing the aileron control horn.
3. Installing the aileron linkages.
Instruction Manual Mustang P51
16 17 18
19 20 21
22 23 24
25 26 27
28 29 30
2
The aileron control horn. Mark four holes from the control horn
onto the bottom of the aileron. Drill four holes onto the aileron.
Install the the control horn onto the
aileron. Cut away the screw. Secure the bolts by C.A glue.
Install the nylon control clasp. Make the same way to install the
second flap control horn. Make the same way to install the
control horn for the second wing.
The aileron linkage. Install the connector rod to the metal
clevis. Glue the carbon rod using the C.A glue.
Secure the bolts and the nylon clasp by
C.A glue. Make the same way to install the flap
linkage. Make the same way for the second wing.
Four holes
Nylon clasp
Clevis Carbon tube
Connector
Glue the wing joiner to the wing by
epoxy glue.
4. Joining the wing halves.
5. Install the landing gear.
Instruction Manual Mustang P51
31 32 33
34 35 36
37 38 39
40 41 42
43 44 45
3
Glue the servo tray by C.A glue. Glue the servo tray into the wing. Draw a center line.
Glue the wing by epoxy glue. Apply the trim tape to the center
section of the wing where they join.
Install the gear servo into the sevo tray. One set of the landing gear. Insert the landing gear into the block
and mark four holes onto the block.
Take out the landing gear and drill four
holes into the block. Attach the metal rod to the landing
gear. Install and secure the landing gear into
the block.
Prepare the plastic part. Glue the plastic part by C.A glue and
make a hole. Install the wheel into the connector of
the gear.
Center line
Clevis Metal rod
Drill a hole
Make a center line onto the horizontal.
4
6. Installing the horizontal stabilizer and the vertical stabilizer.
Instruction Manual Mustang P51
52 53 54
55 56
57 58 59
46 47 48
49 50 51
Install the metal connector to the
landing gear. Install two metal connector to the servo
arm of the gear servo. Install the servo arm and attach two
rods to the metal connector.
Prepare the plastic part. Glue the plastic part to the landing gear. Make the same way for installing the
second landing gear.
Remove the covering from the rear of
the fuselage. Cut away the covering from the
fuselage.
Attach the horizontal to the fuselage
and check it. Mark the shape of the fuselage onto the
bottom of the horizontal.
Remove the covering from the bottom
of the horizontal. Remove the covering from the rear of
the vertical.
Insert the hinge into the slot.
C1 C2
C1 = C2
Center line
7. Installing the elevator and the rudder pushrod.
Instruction Manual Mustang P51
65 66 67
68 69 70
71 72 73
5
The control horn of the elevator. Place the control horn onto the bottom
of the elevator and mark 4 holes. Drill four holes onto the elevator.
Install the control horn onto the elevator. Cut away the screws if neccessary. Secure the bolts by C.A glue.
Attach the nylon clasp. Secure the bolt and nylon clasp by C.A
glue.
Remove the covering.
60 61 62
63 64
Attach the horizontal and the vertical to
the fuselage. Mark the shape of the vertical onto the
top of the horizontal. Remove the covering from the top of
the horizontal.
Glue the horizontal into the fuselage by
epoxy. Glue the vertical into the fuselage by
epoxy and also glue the hinge of rudder.
a1 a2
a1 = a2
Four holes
Nylon clasp
8. Installing the tail gear.
Instruction Manual Mustang P51
74 75 76
77 78 79
80 81 82
83 84 85
86 87 88
6
Push the elevator pushrod out of the exit. Install the metal clevis to the elevator
pushrod. Attach the metal clevis to the control
horn.
Make the same way for the second
elevator pushrod. The control horn of the rudder. Place the cotrol horn onto the rudder
and drill four holes.
Install the nylon control horn onto the
rudder. Cut away the screws if neccessary. Secure the bolt and nylon clasp by C.A
glue.
Install the clasp to the control horn. Attach the metal clevis to the control
horn and lock the cable. Make the same way for the second cable.
The tail gear. Cut away the wood from the bottom of
the rudder.
Install the two nylon clasp onto the
rudder.
9. Installing the fuselage servos.
10. Installing the fuel tank and the engine.
Instruction Manual Mustang P51
89 90 91
92 93 94
95 96 97
98 99
100
101 102 103
7
Glue the two nylon clasp by C.A glue. Install the wheel and the collar into the
tail gear. Install the tail gear into the fuslage and
secure it.
Install the first of the elevator servo. Bend the first of the elevator pushrod. Attach the nylon clasp to the servo arm.
Secure the servo arm. Make the same way for the second of
the elevator servo. Install the rudder servo.
Attach two metal clevis to the servo
arm and lock the cable. Install the throttle servo. Install the metal connector to the servo
arm and secure the servo arm.
The engine mount Mark four holes onto the F1 of the
fuselage.
Drill four holes onto the F1 of the
fuselage.
Four holes
Instruction Manual Mustang P51
104 105 106
107 108 109
110 111 112
113 114 115
116 117 118
8
Install the engine mount to the F1. Prepare the stopper for the tank. Install the stopper to the tank.
Secure the stopper. Install the silicon tube to the tank (not
included) Slide the fuel tank to the fuselage.
3 silicon tubes. Attach the engine to the engine mount
and mark four holes. Drill four holes onto the engine mount.
Drill a holes for throttle rod. Install the throttle rod. Glue the nylon housing.
Attach the throttle rod to the arm of
the carburator. Install the engine and secure it. Secure the muffler.
Andere Handbücher für Mustang P51
1
Inhaltsverzeichnis
Andere Phoenix Model Spielzeug Handbücher
Phoenix Model
Phoenix Model Classic Bedienungsanleitung
Phoenix Model
Phoenix Model trainer 60 Bedienungsanleitung
Phoenix Model
Phoenix Model decathlon Bedienungsanleitung
Phoenix Model
Phoenix Model Domino Bedienungsanleitung
Phoenix Model
Phoenix Model Tucano Electric Bedienungsanleitung
Phoenix Model
Phoenix Model LASER Bedienungsanleitung
Phoenix Model
Phoenix Model strega Bedienungsanleitung
Phoenix Model
Phoenix Model Dolphin 40 Bedienungsanleitung
Phoenix Model
Phoenix Model Dolphin Bedienungsanleitung
Phoenix Model
Phoenix Model Classic Bedienungsanleitung
Phoenix Model
Phoenix Model PA-18 Super Cub Bedienungsanleitung
Phoenix Model
Phoenix Model P40 KITTY HAWK Bedienungsanleitung
Phoenix Model
Phoenix Model Classic Bedienungsanleitung
Phoenix Model
Phoenix Model Diabolo Bedienungsanleitung
Phoenix Model
Phoenix Model CLASSIC-EP Bedienungsanleitung
Phoenix Model
Phoenix Model BULLDOG Bedienungsanleitung
Phoenix Model
Phoenix Model decathlon - EP Bedienungsanleitung
Phoenix Model
Phoenix Model YAK54 YAKOVLEV Bedienungsanleitung
Phoenix Model
Phoenix Model EXTRA 260-EP Bedienungsanleitung
Phoenix Model
Phoenix Model yak 55 Bedienungsanleitung
