Pilz PSSu K S 16DO 0.5 Bedienungsanleitung

PSSu K S 16DO 0.5

Operating Manual 22059-EN-08

}Decentralised system PSSuniversal I/O

Preface

This document is a translation of the original document.

All rights to this documentation are reserved by Pilz GmbH & Co. KG. Copies may be made

for internal purposes. Suggestions and comments for improving this documentation will be

gratefully received.

Source code from third-party manufacturers or open source software has been used for

some components. The relevant licence information is available on the Internet on the Pilz

homepage.

Pilz®, PIT®, PMI®, PNOZ®, Primo®, PSEN®, PSS®, PVIS®, SafetyBUS p®,

SafetyEYE®, SafetyNET p®, the spirit of safety® are registered and protected trademarks

of Pilz GmbH & Co. KG in some countries.

SD means Secure Digital

Contents

Operating Manual PSSu K S 16DO 0.5

22059-EN-08 3

Section 1 Introduction 5

1.1 Validity of documentation 5

1.1.1 Retaining the documentation 5

1.1.2 Terminology: System environment A and B 5

1.2 Definition of symbols 6

Section 2 Overview 7

2.1 Module structure 7

2.2 Module features 7

2.3 Front view 8

Section 3 Safety 9

3.1 Intended use 9

3.2 Safety regulations 10

3.2.1 Use of qualified personnel 10

3.2.2 Warranty and liability 10

3.2.3 Disposal 10

Section 4 Function description 11

4.1 Block diagram 11

4.2 Module features 11

4.2.1 Function description 11

4.2.2 Integrated protection mechanisms 12

4.2.3 Reaction times 12

4.3 Configuration 12

4.3.1 PSSu assignment in system environment A 12

4.3.1.1 Addresses in the process image 12

4.3.2 PSSu assignment in system environment B 12

Section 5 Installation 13

5.1 General installation guidelines 13

5.1.1 Dimensions 13

5.2 Install compact module 15

5.3 Install/uninstall connector 17

5.4 Install labelling bracket 19

Section 6 Wiring 20

6.1 General wiring guidelines 20

6.1.1 Connectors' mechanical connection 20

6.1.2 Connect/disconnect the cables 20

6.2 Terminal configuration 22

6.3 Connecting the module 24

Section 7 Operation 25

7.1 Messages 25

7.2 Display elements 26

7.2.1 Display elements for module diagnostics 26

Contents

Operating Manual PSSu K S 16DO 0.5

22059-EN-08 4

7.2.2 Display elements for output status 26

Section 8 Technical details 27

Section 9 Order reference 30

9.1 Product 30

9.2 Accessories 30

Introduction

Operating Manual PSSu K S 16DO 0.5

22059-EN-08 5

1 Introduction

1.1 Validity of documentation

This documentation is valid for the product PSSu K S 16DO 0.5. It is valid until new docu-

mentation is published.

This operating manual explains the function and operation, describes the installation and

provides guidelines on how to connect the product.

1.1.1 Retaining the documentation

This documentation is intended for instruction and should be retained for future reference.

1.1.2 Terminology: System environment A and B

The PSSu system can be used in two different system environments. The module's applic-

ation area is described in the chapter "Intended Use" of the manual.

The distinction is made between

}PSSu in system environment A

}PSSu in system environment B

The distinction is based on the application area of the PSSu system.

PSSu in system environment A may be used in the

}Decentralised system PSSu I/O

}Not in the automation system PSS 4000

PSSu in system environment B may be used in the

}Automation system PSS 4000, e.g. with

– Decentralised system PSSu I/O with SafetyNET p

– Control system PSSu PLC

– Control system PSSu multi

Introduction

Operating Manual PSSu K S 16DO 0.5

22059-EN-08 6

1.2 Definition of symbols

Information that is particularly important is identified as follows:

DANGER!

This warning must be heeded! It warns of a hazardous situation that poses

an immediate threat of serious injury and death and indicates preventive

measures that can be taken.

WARNING!

This warning must be heeded! It warns of a hazardous situation that could

lead to serious injury and death and indicates preventive measures that can

be taken.

CAUTION!

This refers to a hazard that can lead to a less serious or minor injury plus

material damage, and also provides information on preventive measures

that can be taken.

NOTICE

This describes a situation in which the product or devices could be dam-

aged and also provides information on preventive measures that can be

taken. It also highlights areas within the text that are of particular import-

ance.

INFORMATION

This gives advice on applications and provides information on special fea-

tures.

Overview

Operating Manual PSSu K S 16DO 0.5

22059-EN-08 7

2 Overview

2.1 Module structure

The module combines the function unit (inputs or outputs) and connection levels in one

housing.

Wiring is via 10-pin or 30-pin connectors with spring-loaded terminals, which are plugged

into the connector strips on the module.

Details of the applicable connectors with spring-loaded terminals are available in the

chapter entitled “Intended Use”.

2.2 Module features

The product has the following features:

}16 Digital outputs

– Semiconductor technology

– Single-pole

– Positive-switching

– Current load capacity per output: 0,50 A

– Short circuit-proof

– Overload-proof

}LEDs for:

– Switch status of each output

– Module error

}2 x 10-pin connector strip

}Communication via:

– Standard fieldbus

}For standard applications in system environment A and B

Accessories:

}Connector with spring-loaded terminals (necessary for operation)

}Labelling bracket

}Labelling strips (sheets)

Overview

Operating Manual PSSu K S 16DO 0.5

22059-EN-08 8

2.3 Front view

Key:

}1: Labelling strip with:

– 2D code

– Order Number

– Serial Number

– Hardware version number

}2: Name of compact module

}3: Connector strip X1 for connectors with spring-loaded terminals

}4: Connector strip X2 for connectors with spring-loaded terminals

}5: Labelling strip for connector strip X2

}6: Labelling strip for connector strip X1

}7: LEDs for status display and module diagnostics

Safety

Operating Manual PSSu K S 16DO 0.5

22059-EN-08 9

3 Safety

3.1 Intended use

The module provides type 1 outputs in accordance with IEC 61131-2. It may be used to

switch:

}Resistive loads

}Inductive loads

}Capacitive loads

The module PSSu K S 16DO 0.5 may be used as a safety component in accordance with

the Lifts Directive 95/16/EC, EN81-1, EN81-2 and EN115-1.

The programmable safety system should be installed in a protected environment that meets

at least the requirements of pollution degree 2. Example: Protected inside space or control

cabinet with protection class IP54 and corresponding air conditioning.

Intended use includes making the electrical installation EMC-compliant. Please refer to the

guidelines stated in the "PSSuniversal Installation Manual". The module is designed for use

in an industrial environment. It is not suitable for use in a domestic environment, as this can

lead to interference.

The following is deemed improper use in particular:

}Any component, technical or electrical modification to the module

}Use of the module outside the areas described in this manual

}Any use of the module that is not in accordance with the technical details.

INFORMATION

The module is supported by:

}PSSuniversal Configurator and PSSuniversal Assistant from Version

1.8.1.

}PAS4000 from version 1.7.0

– We recommend that you always use the latest version (download

from www.pilz.de).

The PSSu K S 16DO 0.5 module may be used with the following connectors with spring-

loaded terminals:

}PSSu A Con 1/10 C

}PSSu A Con 3/30 C

WARNING!

The module may not be used in combination with PSSu E F BSW(-T) mod-

ules in safety-related applications.

Safety

Operating Manual PSSu K S 16DO 0.5

22059-EN-08 10

3.2 Safety regulations

3.2.1 Use of qualified personnel

The products may only be assembled, installed, programmed, commissioned, operated,

maintained and decommissioned by competent persons.

A competent person is someone who, because of their training, experience and current pro-

fessional activity, has the specialist knowledge required to test, assess and operate the

work equipment, devices, systems, plant and machinery in accordance with the general

standards and guidelines for safety technology.

It is the company’s responsibility only to employ personnel who:

}Are familiar with the basic regulations concerning health and safety / accident preven-

tion

}Have read and understood the information provided in this description under "Safety"

}And have a good knowledge of the generic and specialist standards applicable to the

specific application.

3.2.2 Warranty and liability

All claims to warranty and liability will be rendered invalid if

}The product was used contrary to the purpose for which it is intended

}Damage can be attributed to not having followed the guidelines in the manual

}Operating personnel are not suitably qualified

}Any type of modification has been made (e.g. exchanging components on the PCB

boards, soldering work etc.).

3.2.3 Disposal

}In safety-related applications, please comply with the mission time TM in the safety-re-

lated characteristic data.

}When decommissioning, please comply with local regulations regarding the disposal of

electronic devices (e.g. Electrical and Electronic Equipment Act).

Inhaltsverzeichnis

Andere Pilz Steuereinheit Handbücher

Pilz

Pilz PNOZ m EF 8DI4DO Bedienungsanleitung

Pilz

Pilz PSSu E PD1-T Bedienungsanleitung

Pilz

Pilz PSSu K F EI Bedienungsanleitung

Pilz

Pilz PNOZ mi1p Bedienungsanleitung

Pilz

Pilz PSSu K S RS232 Modbus ASCII Bedienungsanleitung

Pilz

Pilz PZE X4VP4 Bedienungsanleitung

Pilz

Pilz PIT gb LLLE Bedienungsanleitung

Pilz

Pilz PNOZ p1vp Bedienungsanleitung

Pilz

Pilz PSEN cs5.11n Bedienungsanleitung

Pilz

Pilz PSSu E F 2DI 60-R Bedienungsanleitung

Pilz

Pilz PNOZ ma1p Bedienungsanleitung

Pilz

Pilz PSSu E F PS2 Bedienungsanleitung

Pilz

Pilz PNOZ m ES ETH Bedienungsanleitung

Pilz

Pilz PNOZ mi2p Bedienungsanleitung

Pilz

Pilz PIT es Set10u-5c PCB Bedienungsanleitung

Pilz

Pilz PSSu E F 2DO 2 Bedienungsanleitung

Pilz

Pilz PSEN ma1.4-51 M12/8-0.15m Bedienungsanleitung

Pilz

Pilz ms3p HTL Bedienungsanleitung

Pilz

Pilz PNOZ mc4p Bedienungsanleitung

Pilz

Pilz PIT m3.3p Bedienungsanleitung

Pilz

Pilz PZE 9P Bedienungsanleitung

Pilz

Pilz PNOZ s11 Bedienungsanleitung

Pilz

Pilz PNOZ mmc12p Bedienungsanleitung

Pilz

Pilz PMCtendo SZ Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung