Pilz PNOZ m B0 Bedienungsanleitung

PNOZ m B0

Operating Manual-1002660-EN-07

}Configurable, safe small controllers PNOZmulti 2

Preface

This document is the original document.

All rights to this documentation are reserved by Pilz GmbH & Co. KG. Copies may be made

for the user's internal purposes. Suggestions and comments for improving this documenta-

tion will be gratefully received.

Source code from third-party manufacturers or open source software has been used for

some components. The relevant licence information is available on the Internet on the Pilz

homepage.

Pilz®, PIT®, PMI®, PNOZ®, Primo®, PSEN®, PSS®, PVIS®, SafetyBUS p®,

SafetyEYE®, SafetyNET p®, the spirit of safety® are registered and protected trademarks

of Pilz GmbH & Co. KG in some countries.

SD means Secure Digital

Contents

Operating Manual PNOZ m B0

1002660-EN-07 3

Section 1 Introduction 5

1.1 Validity of documentation 5

1.2 Using the documentation 5

1.3 Definition of symbols 5

Section 2 Overview 7

2.1 Range 7

2.2 Unit features 7

2.3 Chip card 8

2.4 Front view 9

Section 3 Safety 10

3.1 Intended use 10

3.2 System requirements 10

3.3 Safety regulations 10

3.3.1 Safety assessment 10

3.3.2 Use of qualified personnel 11

3.3.3 Warranty and liability 11

3.3.4 Disposal 11

3.3.5 For your safety 11

Section 4 Function description 13

4.1 Integrated protection mechanisms 13

4.2 Functions 13

4.3 System reaction time 13

4.4 Block diagram 13

4.5 Diagnostics 14

Section 5 Installation 15

5.1 Control cabinet installation 15

5.1.1 Mounting distances 15

5.2 Dimensions in mm 17

5.3 Install base unit without expansion module 17

5.4 Connecting the base unit and expansion modules 18

Section 6 Commissioning 19

6.1 General wiring guidelines 19

6.2 Commissioning the control system 19

6.2.1 Connection 20

6.2.2 Load project from chip card 22

6.2.3 Load project via USB port 22

6.3 Function test during commissioning 23

6.4 Using the chip card 23

6.5 Connection example 24

Contents

Operating Manual PNOZ m B0

1002660-EN-07 4

Section 7 Operation 25

7.1 LED indicators 25

7.2 Display indicators 26

7.2.1 Rotary knob 28

7.2.1.1 Function 28

7.2.1.2 Pull out and retract the knob 28

7.2.1.3 Rotate and press the knob 28

7.2.2 Switch between menu levels 29

7.2.3 Unit diagnostics on the LC display 30

7.2.4 Error stack on the LC display 31

Section 8 Technical details 32

8.1 Safety characteristic data 35

8.2 Classification according to ZVEI, CB24I 36

Section 9 Supplementary data 38

9.1 Maximum capacitive load C (μF) with load current I (A) at the semicon-

ductor outputs

9.2 Maximum permitted total current of the semiconductor outputs 38

9.3 Maximum permitted humidity 39

9.3.1 Max. relative humidity, operation 39

9.3.2 Max. relative humidity, storage 39

Section 10 Order reference 40

10.1 Product 40

10.2 Accessories 40

Introduction

Operating Manual PNOZ m B0

1002660-EN-07 5

1 Introduction

1.1 Validity of documentation

This documentation is valid for the product PNOZ m B0. It is valid until new documentation

is published.

This operating manual explains the function and operation, describes the installation and

provides guidelines on how to connect the product.

1.2 Using the documentation

This document is intended for instruction. Only install and commission the product if you

have read and understood this document. The document should be retained for future ref-

erence.

1.3 Definition of symbols

Information that is particularly important is identified as follows:

DANGER!

This warning must be heeded! It warns of a hazardous situation that poses

an immediate threat of serious injury and death and indicates preventive

measures that can be taken.

WARNING!

This warning must be heeded! It warns of a hazardous situation that could

lead to serious injury and death and indicates preventive measures that can

be taken.

CAUTION!

This refers to a hazard that can lead to a less serious or minor injury plus

material damage, and also provides information on preventive measures

that can be taken.

NOTICE

This describes a situation in which the product or devices could be dam-

aged and also provides information on preventive measures that can be

taken. It also highlights areas within the text that are of particular import-

ance.

Introduction

Operating Manual PNOZ m B0

1002660-EN-07 6

INFORMATION

This gives advice on applications and provides information on special fea-

tures.

Overview

Operating Manual PNOZ m B0

1002660-EN-07 7

2 Overview

2.1 Range

}Base unit PNOZ m B0

}Terminator

}Documentation on data medium

2.2 Unit features

Application of the product PNOZ m B0:

Base unit of the configurable control system PNOZmulti 2

The product has the following features:

}Can be configured in the PNOZmulti Configurator

}Semiconductor outputs:

4 safety outputs

Depending on the application, up to PL e of EN ISO 13849-1 and up to SIL CL 3 of EN

IEC 62061

}12 inputs for connecting, for example:

– Emergency stop pushbutton

– Two-hand pushbuttons

– Safety gate limit switches

– Start button

– Light beam devices

– Scanner

– Enabling switch

– PSEN

– Operating mode selector switch

}8 configurable inputs/outputs

Can be configured as:

– Inputs (see above for connection options)

– Auxiliary outputs

}4 configurable outputs

Can be configured as:

– Auxiliary outputs

– Test pulse outputs

Overview

Operating Manual PNOZ m B0

1002660-EN-07 8

}LED display for:

– Error messages

– Diagnostics

– Supply voltage

– Fault at the outputs

– Fault at the inputs

}Backlit display for:

– Error messages

– State of supply voltage

– State of the inputs and outputs

– Status information

– Unit information

}Test pulse outputs used to monitor shorts across the inputs

}Monitoring of shorts between the safety outputs

}Plug-in connection terminals:

Either spring-loaded terminal or screw terminal available (see Order references).

}Rotary knob for menu control

}Expansion modules can be connected

(please refer to the document "PNOZmulti System Expansion" for details of the type

and number that can be connected)

2.3 Chip card

To be able to use the product you will need a chip card.

Chip cards are available with memories of 8 kByte and 32 kByte. For large-scale projects

we recommend the 32 kByte chip card (see Technical Catalogue: Accessories chapter).

Overview

Operating Manual PNOZ m B0

1002660-EN-07 9

2.4 Front view

Fig.: Front view with and without cover

Legend

X1: Inputs I8 ... I15

X2: Configurable test pulse/auxiliary outputs T0M20 ... T3M23

Semiconductor outputs O0 ... O3

X3: Configurable inputs/outputs IM0 – IM3

Inputs I4 ... I7

X4: Configurable inputs/outputs IM16 – IM19

Supply connections

LEDs: PWR

RUN

DIAG

FAULT

I FAULT

O FAULT

Safety

Operating Manual PNOZ m B0

1002660-EN-07 10

3 Safety

3.1 Intended use

The configurable system PNOZmulti 2 is used for the safety-related interruption of safety

circuits and is designed for use in:

}Emergency stop equipment

}Safety circuits in accordance with VDE0113 Part 1 and EN60204-1

CAUTION!

Inputs and outputs for standard functions must not be used for safety-re-

lated applications.

}The product PNOZ m B0 meets the requirements of the standards EN 81-20, EN 81-22

and EN 81-50, harmonised under the Lifts Directive 2014/33/EU, and the requirements

of the standard EN 115-1, harmonised under the Machinery Directive 2006/42/EC.

}The programmable safety system should be installed in a protected environment that

meets at least the requirements of pollution degree 2.

Example: Protected inside space or control cabinet with protection type IP54 and cor-

responding air conditioning.

The following is deemed improper use in particular

}Any component, technical or electrical modification to the product,

}Use of the product outside the areas described in this manual,

}Use of the product outside the technical details (see Technical details [ 32]).

NOTICE

EMC-compliant electrical installation

The product is designed for use in an industrial environment. The product

may cause interference if installed in other environments. If installed in other

environments, measures should be taken to comply with the applicable

standards and directives for the respective installation site with regard to in-

terference.

3.2 System requirements

Please refer to the "Product Modifications" document in the "Version overview" section for

details of which versions of the PNOZmulti Configurator can be used for this product.

3.3 Safety regulations

3.3.1 Safety assessment

Before using a device it is necessary to perform a safety assessment in accordance with

the Machinery Directive.

Andere Handbücher für PNOZ m B0

Inhaltsverzeichnis

Andere Pilz Controller Handbücher

Pilz

Pilz PSSuniversal multi PSSu H m F DP ETH SD Bedienungsanleitung

Pilz

Pilz PNOZ mmc7p CC Bedienungsanleitung

Pilz

Pilz PNOZ m EF 1MM Bedienungsanleitung

Pilz

Pilz PSEN sl-0.5p 1.1 Bedienungsanleitung

Pilz

Pilz PNOZ m3p (ETH) Bedienungsanleitung

Pilz

Pilz PITmode flex Bedienungsanleitung

Pilz

Pilz PSS 3075-3 Series Bedienungsanleitung

Pilz

Pilz PIT es6 Series Bedienungsanleitung

Pilz

Pilz 20 748-03 Bedienungsanleitung

Pilz

Pilz PNOZ m EF SafetyNET Bedienungsanleitung

Pilz

Pilz PMotion Bedienungsanleitung

Pilz

Pilz PNOZ mc1p Bedienungsanleitung

Pilz

Pilz PNOZmulti Classic PNOZ ms3p TTL Bedienungsanleitung

Pilz

Pilz PMUT X1P Bedienungsanleitung

Pilz

Pilz PNOZ mmc4p Bedienungsanleitung

Pilz

Pilz PNOZ m B1 Bedienungsanleitung

Pilz

Pilz PSEN sl-0.5n 1.1 Bedienungsanleitung

Pilz

Pilz PNOZ mm0.2p Bedienungsanleitung

Pilz

Pilz PNOZmulti PNOZ mmc3p Bedienungsanleitung

Pilz

Pilz PIT js2 Bedienungsanleitung

Pilz

Pilz PSEN 2.1b-26 Bedienungsanleitung

Pilz

Pilz PNOZ m EF Multi Link Bedienungsanleitung

Pilz

Pilz PNOZ m C0 Bedienungsanleitung

Pilz

Pilz PSEN sl-1.0p 3.1 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch