Pilz PSSu E F PS Bedienungsanleitung

PSSu E F PS(-T)

Operating Manual-21292-EN-06

}Decentralised system PSSuniversal I/O

Preface

This document is a translation of the original document.

All rights to this documentation are reserved by Pilz GmbH & Co. KG. Copies may be made

for internal purposes. Suggestions and comments for improving this documentation will be

gratefully received.

Source code from third-party manufacturers or open source software has been used for

some components. The relevant licence information is available on the Internet on the Pilz

homepage.

Pilz®, PIT®, PMI®, PNOZ®, Primo®, PSEN®, PSS®, PVIS®, SafetyBUS p®,

SafetyEYE®, SafetyNET p®, the spirit of safety® are registered and protected trademarks

of Pilz GmbH & Co. KG in some countries.

SD means Secure Digital

Contents

Operating Manual PSSu E F PS(-T)

21292-EN-06 3

Section 1 Introduction 5

1.1 Validity of documentation 5

1.1.1 Retaining the documentation 5

1.2 Definition of symbols 5

Section 2 Overview 7

2.1 Module structure 7

2.2 Module features 7

2.3 Front view 8

Section 3 Safety 10

3.1 Intended use 10

3.2 Safety regulations 11

3.2.1 Use of qualified personnel 11

3.2.2 Warranty and liability 11

3.2.3 Disposal 11

Section 4 Function description 12

4.1 Block diagram 12

4.2 Module features 12

4.2.1 Supply voltage 12

4.2.1.1 Current load capacity 13

4.2.2 Integrated protection mechanisms 15

4.3 Configuration 15

4.3.1 Application as a general supply module 15

4.3.1.1 Addresses in the process image 16

4.3.1.2 FS error behaviour 16

Section 5 Installation 17

5.1 General installation guidelines 17

5.1.1 Dimensions 17

5.2 Installing the base module 18

5.3 Inserting and removing an electronic module 19

5.3.1 Inserting an electronic module 20

5.3.2 Removing an electronic module 21

5.3.3 Changing an electronic module during operation 21

Section 6 Wiring 22

6.1 General wiring guidelines 22

6.1.1 Mechanical connection of the base modules 22

6.2 Terminal configuration 24

6.3 Connecting the module 27

Section 7 Operation 29

7.1 Messages 29

7.2 Display elements 29

7.2.1 Anzeigeelemente zur Moduldiagnose 29

Contents

Operating Manual PSSu E F PS(-T)

21292-EN-06 4

7.2.2 Display elements for the status of the module supply and periphery supply 30

7.3 Status byte 31

Section 8 Technical details 32

Section 9 Order reference 35

9.1 Product 35

9.2 Accessories 35

Introduction

Operating Manual PSSu E F PS(-T)

21292-EN-06 5

1 Introduction

1.1 Validity of documentation

This documentation is valid for the products PSSu E F PS and PSSu E F PS-T. It is valid

until new documentation is published.

This operating manual explains the function and operation, describes the installation and

provides guidelines on how to connect the product.

1.1.1 Retaining the documentation

This documentation is intended for instruction and should be retained for future reference.

1.2 Definition of symbols

Information that is particularly important is identified as follows:

DANGER!

This warning must be heeded! It warns of a hazardous situation that poses

an immediate threat of serious injury and death and indicates preventive

measures that can be taken.

WARNING!

This warning must be heeded! It warns of a hazardous situation that could

lead to serious injury and death and indicates preventive measures that can

be taken.

CAUTION!

This refers to a hazard that can lead to a less serious or minor injury plus

material damage, and also provides information on preventive measures

that can be taken.

NOTICE

This describes a situation in which the product or devices could be dam-

aged and also provides information on preventive measures that can be

taken. It also highlights areas within the text that are of particular import-

ance.

Introduction

Operating Manual PSSu E F PS(-T)

21292-EN-06 6

INFORMATION

This gives advice on applications and provides information on special fea-

tures.

Overview

Operating Manual PSSu E F PS(-T)

21292-EN-06 7

2 Overview

2.1 Module structure

A module consists of

}Electronic module and

}Base module with

– Screw terminals or

– Cage clamp terminals

The base modules are the carrier units for the electronic modules and are used to connect

the field wiring. The electronic modules are inserted on to the base modules and determine

the module's function.

Details of the base modules that can be used are available in the chapter entitled “Intended

Use”.

2.2 Module features

The product has the following features:

}Current load capacity of module supply max. 1,5 A

}The module supply is not buffered if the supply voltage is interrupted

}Separate infeed for periphery supply

}Separate infeed for module supply

}Infeed for C-rail supply

}LEDs for:

– Module supply

– Periphery supply

– Module error

}Application range depends on the base module

}T-type:

PSSu E F PS-T: for increased environmental requirements

Overview

Operating Manual PSSu E F PS(-T)

21292-EN-06 8

2.3 Front view

2111

2212

2313

Err

11 21

13 23

PSSu E F

5 V 24V

0V24V

24V 24V

2414

PSSu E F

312190

000000

001

Key:

}A: Electronic module

}B: Base module

}1: LED for module diagnostics

}2: Labelling strip with:

– Name of electronic module

– Order number

– Serial number

– Hardware version number

– 2D code

}3: Labelling strip for the terminal configuration on the base module

}4: Name of electronic module

}5: Connection level 1

}6: Connection level 2

}7: Connection level 3

}8: Connection level 4

Overview

Operating Manual PSSu E F PS(-T)

21292-EN-06 9

}9: Square mounting holes (connection levels 1, 2, 3 and 4)

– With screw to loosen/tighten the screw terminal on base modules with screw termin-

als

– With mechanism to operate the cage clamp on base modules with cage clamp ter-

minals

}10: Round connection holes (connection levels 1, 2, 3 and 4) for connecting the signal

lines

}11: Mounting slot for colour marker to label the connection level (connection levels 1, 2,

3 and 4)

Safety

Operating Manual PSSu E F PS(-T)

21292-EN-06 10

3 Safety

3.1 Intended use

The module provides the supply for the module supply and periphery supply within the sys-

tem.

Depending on which base module is used, the module may be used as a:

}General supply module (first module after a head module, if the head module does not

have an integrated supply voltage)

}Supply module to refresh the module supply and periphery supply

}Supply module to form supply groups

The module PSSu E F PS-T is suitable for use where there are increased environmental re-

quirements (see Technical Details).

Intended use includes making the electrical installation EMC-compliant. Please refer to the

guidelines stated in the "PSSuniversal Installation Manual". The module is designed for use

in an industrial environment. It is not suitable for use in a domestic environment, as this can

lead to interference.

The following is deemed improper use in particular:

}Any component, technical or electrical modification to the module

}Use of the module outside the areas described in this manual

}Any use of the module that is not in accordance with the technical details.

INFORMATION

The module is supported by

}PSSuniversal Configurator and PSSuniversal Assistant from Version

1.4.0

}PAS4000 from Version 1.0.0

– We recommend that you always use the latest version (download

from www.pilz.com).

The PSSu E F PS module may be used in conjunction with the following base modules:

}PSSu BS 1/8 S

}PSSu BS-R 1/8 S

}PSSu BS 1/8 C

}PSSu BS-R 1/8 C

The module PSSu E F PS-T may be used in conjunction with the following base modules:

}PSSu BS 1/8 S-T

}PSSu BS-R 1/8 S-T

}PSSu BS 1/8 C-T

}PSSu BS-R 1/8 C-T

Andere Handbücher für PSSu E F PS

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Pilz E/A-System Handbücher

Pilz

Pilz PSS u2 ES 8PTD 24V 0V Bedienungsanleitung

Pilz

Pilz PSSu E S 4DI-D Bedienungsanleitung

Pilz

Pilz PSSu E F PS Bedienungsanleitung

Pilz

Pilz PSSu E F 2DO 2 Bedienungsanleitung

Pilz

Pilz PDP67 F 8DI ION HP Bedienungsanleitung

Pilz

Pilz PSSu H F PN o Bedienungsanleitung

Pilz

Pilz PSSu K S 8DI 8DO 0.5 Bedienungsanleitung

Pilz

Pilz PNOZ m EF 4AI Bedienungsanleitung

Pilz

Pilz PSSu E F 4DI Bedienungsanleitung

Pilz

Pilz PSSu H FS2 SN SD Bedienungsanleitung

Pilz

Pilz PSS u2 P0 F/S EIP Bedienungsanleitung

Pilz

Pilz PSS u2 ES 4DOD 2A Bedienungsanleitung

Pilz

Pilz PSSu H SB-T Bedienungsanleitung

Pilz

Pilz PSSu E S 2DOR 2 Bedienungsanleitung

Pilz

Pilz PSS u2 ES 8DID Bedienungsanleitung

Pilz

Pilz PSS u2 EF 8DO 0.5A Bedienungsanleitung

Pilz

Pilz PSSu K S RS232 Modbus ASCII Bedienungsanleitung

Pilz

Pilz PSS u2 ES 8DOD 0.5A Bedienungsanleitung

Pilz

Pilz PSSu E PS-P +/-10V Bedienungsanleitung

Pilz

Pilz PSSu E F AI U Bedienungsanleitung

Pilz

Pilz PSS u2 ES 16PT 0V Bedienungsanleitung

Pilz

Pilz PSSu E S 2AI U Bedienungsanleitung

Pilz

Pilz PDP67 F 8DI ION PT Bedienungsanleitung

Pilz

Pilz PSSu E S 2AO I Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung