Pioneer AVIC-X1BT Bedienungsanleitung

MANUEL D’INSTALLATION

INSTALLATION MANUAL

AVIC-X1BT

This product conforms to new cord colours.

Los colores de los cables de este producto se confor-

man con un nuevo código de colores.

Dieses Produkt entspricht den neuen kabelfarben.

Le code de couleur des câbles utilisé pour ce produit est

nouveau.

Questo prodotto è conforme ai nuovi codici colori.

De kleuren van de snoeren van dit toestel zijn gewijzigd.

English Español Deutsch Français Italiano Nederlands

IMPORTANT INFORMATION

ABOUT YOUR NEW NAVIGATION SYSTEM AND THIS MANUAL

• The navigation features of this product (and rear view camera option if pur-

chased) is intended solely as an aid to you in the operation of your vehicle. It is

not a substitute for your attentiveness, judgement and care when driving.

• Never use this navigation system to route to hospitals, police stations, or similar

facilities in an emergency, Please call the appropriate emergency number.

• Do not operate this navigation system (or the rear view camera option if pur-

chased) if doing so in any way will divert your attention from the safe operation

of your vehicle. Traffic restrictions and advisories currently in force should

always take precedence over guidance given by this product. Always obey current

traffic restrictions, even if this product provides contrary advice.

• This manual explains how to install this navigation system in your vehicle.

Operation of this navigation system is explained in the separate Operation

Manual or Hardware Manual for the navigation system.

• Do not install this product where it may (i) obstruct the driver’s vision, (ii) impair

the performance of any of the vehicle’s operating systems of safety features,

including airbags, hazard lamp buttons or (iii) impair the driver’s ability to safely

operate the vehicle. In some cases, it may not be possible to install this product

because of the vehicle type or the shape of the vehicle interior.

English Español Deutsch Français Italiano Nederlands

IMPORTANT INFORMATION .................... 1

ABOUT YOUR NEW NAVIGATION

SYSTEM AND THIS MANUAL .............. 1

IMPORTANT SAFEGUARDS .................... 3

PLEASE READ ALL OF THESE

INSTRUCTIONS REGARDING

YOUR NAVIGATION

SYSTEM AND RETAIN THEM

FOR FUTURE REFERENCE .................... 3

Connecting the System ............................ 4

-Before installing this product

-To prevent damage

-Parts supplied

Connecting the system ...................................... 7

Connecting the power cord (1) .......................... 9

Connecting the power cord (2) ........................ 11

When connecting to separately sold power

amp .......................................................... 13

When connecting a Rear view camera ............ 15

When connecting the external video component

and the display .......................................... 16

-When using a display connected to rear video

output

Installation ................................................ 17

To guard against electromagnetic

interference .............................................. 18

Before installing .............................................. 18

Installing this product ...................................... 19

-Installation notes

-Parts supplied

-Installing the Hide-away unit

-DIN Front/Rear-mount

-DIN Front-mount

-DIN Rear-mount

-Fixing the front panel

-Installing the Bluetooth adapter

-When installing the microphone on the sun

visor

-When installing the microphone on the steer-

ing column

Adjusting the microphone angle ...................... 28

Installing the GPS aerial .................................. 29

-Installation notes

-Parts supplied

-When installing the aerial inside the vehicle

(on the rear shelf)

-When installing the aerial outside the vehicle

(on the body)

After Installing this Product.................... 32

Contents

IMPORTANT SAFEGUARDS

PLEASE READ ALL OF THESE INSTRUCTIONS REGARDING YOUR

NAVIGATION SYSTEM AND RETAIN THEM FOR FUTURE REFERENCE

1. Read this manual fully and carefully before installing your navigation system.

2. Keep this manual handy for future reference.

3. Pay close attention to all warnings in this manual and follow the instructions care-

fully.

4. This navigation system may in certain circumstances display erroneous informa-

tion regarding the position of your vehicle, the distance of objects shown on the

screen, and compass directions. In addition, the system has certain limitations,

including the inability to identify one-way streets, temporary traffic restrictions

and potentially unsafe driving areas. Please exercise your own judgement in the

light of actual driving conditions.

5. As with any accessory in your vehicle’s interior, the navigation system should not

divert your attention from the safe operation of your vehicle. If you experience

difficulty in operating the system or reading the display, please make adjustments

while safely parked.

6. Please remember to wear your seat belt at all times while operating your vehicle.

If you are ever in an accident, your injuries can be considerably more severe if

your seat belt is not properly fastened.

7. Certain countries laws may restrict the placement and use of navigation systems

in your vehicle. Please comply with all applicable laws and regulations in the

installation and operation of your navigation system.

Do not attempt to install or service your navigation system by yourself.

Installation or servicing of the navigation system by persons without training and

experience in electronic equipment and automotive accessories may be dangerous

and could expose you to the risk of electric shock or other hazards.

English Español Deutsch Français Italiano Nederlands

Connecting the System

• Pioneer does not recommend that you install your navigation system yourself. We

recommend that only authorised Pioneer service personnel, who have special train-

ing and experience in mobile electronics, set up and install this product. NEVER

SERVICE THIS PRODUCT YOURSELF. Installing or servicing this product and

its connecting cables may expose you to the risk of electric shock or other hazards,

and can cause damage to the navigation system that is not covered by warranty.

• If you decide to perform the installation yourself, and have special training and

experience in the mobile electronics installations, please carefully follow all of the

steps in the Installation Manual.

• Secure all wiring with cable clamps or electrical tape. Do not allow any bare wiring

to remain exposed.

• Do not directly connect the yellow lead of this product to the vehicle battery. If the

lead is directly connected to the battery, engine vibration may eventually cause the

insulation to fail at the point where the wire passes from the passenger compart-

ment into the engine compartment. If the yellow lead’s insulation tears as a result

of contact with metal parts, short-circuiting can occur, resulting in considerable

danger.

• It is extremely dangerous to allow the GPS aerial cable or microphone cable to

become wound around the steering column or gearstick. Be sure to install this

product, its cables, and wiring away in such a way that they will not obstruct or

hinder driving.

• Make sure that the cables and wires are routed and secured so they will not inter-

fere with or become caught in any of the vehicle’s moving parts, especially the

steering wheel, gearstick, handbrake, sliding seat tracks, doors, or any of the vehi-

cle’s controls.

• Do not route wires where they will be exposed to high temperatures. If the insula-

tion heats up, wires may become damaged, resulting in a short circuit or malfunc-

tion and permanent damage to the product.

• Do not cut the GPS aerial cable to shorten it or use an extension to make it longer.

Altering the aerial cable could result in a short circuit or malfunction.

• Do not shorten any leads. If you do, the protection circuit (fuse holder, fuse resister

or filter, etc.) may fail to work properly.

• Never feed power to other electronic products by cutting the insulation of the

power supply lead of the navigation system and tapping into the lead. The current

capacity of the lead will be exceeded, causing overheating.

• The black lead is earth. Please earth this lead separately from the earth of high-

current products such as power amps. Do not earth more than one product togeth-

er with the earth from another product. For example, you must separately earth

any amplifier unit away from the earth of the Hide-away unit. Connecting earths

together can cause a fire and/or damage the products if their earths became

detached.

Connecting the System

Before installing this product

• This product is for vehicles with a 12-volt battery and negative earthing. Check the bat-

tery voltage of your vehicle before installation.

To prevent damage

• When disconnecting a connector, pull the connector itself. Do not pull the lead, as you

may pull it out of the connector.

• This product cannot be installed in a vehicle that does not have an ACC (accessory)

position on the ignition switch.

• To avoid short-circuiting, cover the disconnected lead with insulating tape. It is especial-

ly important to insulate all unused speaker leads, which if left uncovered may cause a

short circuit.

• Attach the connectors of the same colour to the corresponding coloured port, i.e., blue

connector to the blue port, black to black, etc.

• Refer to the owner’s manual for details on connecting the power amp and other units,

then make connections accordingly.

• When replacing the fuse, be sure to only use a fuse of the rating prescribed on the fuse

holder.

• Since a unique BPTL circuit is employed, do not directly earth the ≠side of the speaker

lead or connect the ≠sides of the speaker leads together. Be sure to connect the ≠side

of the speaker lead to the ≠side of the speaker lead on the display unit.

• If the RCA pin jack on this product will not be used, do not remove the caps attached to

the end of the connector.

• Never connect speakers with an output rating of less than 50 W channel or impedance

outside of the 4 ohms to 8 ohms specifications to your navigation system. Connecting

speakers with output and/or impedance values other than those noted here may result in

the speakers catching fire, emitting smoke, or becoming damaged.

•When the auto aerial function is used by connecting the blue lead to the vehicle

with the auto aerial function, either turning off the ignition switch or detaching

the front panel will retract the auto aerial of the vehicle.

No ACC positionACC position

• To avoid shorts in the electrical sys-

tem, be sure to disconnect the (–)

battery cable before beginning

installation.

English Español Deutsch Français Italiano Nederlands

• When the ignition switch is turned on (ACC ON), a control signal is output through the

blue/white lead. Connect to an external power amp’s system remote control terminal

(max. 300 mA 12 V DC). The control signal is output through the blue/white lead, even

if the front panel is detached, or the audio source is switched off.

• When an external power amp is being used with this system, be sure not to connect the

blue lead to the amp’s power terminal. Likewise, do not connect the blue lead to the

power terminal of the auto aerial. Such connection could cause excessive current drain

and malfunction as well as damage to the auto aerial of the vehicle.

Parts supplied

IP-BUS cablePower cordMicrophone

Bluetooth adapterLock tieSystem extension connector

Extension aerial cableGPS aerialExtension lead

(for speed signal)

Extension lead

(for reverse signal)

30-pin cableConnector

Power cordHide-away unitDisplay unit

Connecting the System

Connecting the system

Yellow Hide-away unit

Light grey Blue Blue

AV-BUS cable

(supplied with

TV tuner)

Extension

aerial cable

(supplied)

3 m

When installing

the Hide-away unit

in the boot, etc.,

the extension cable

(e.g. CD-SC300E)

(sold separately)

is required.

Multi-CD player

5 m

IP-BUS cable

GPS aerial

(sold separately)

Blue

Hide-away TV tuner

(e.g. GEX-P5700TVP)

(sold separately)

Black

IP-BUS cable

(supplied with TV tuner)

IP-BUS cable (supplied with iPod adapter)

*: In order to operate the navigation system by

voice, the microphone in the voice recognition

kit (e.g. CD-VC1) (sold separately) is required.

Bluetooth

adapter

(CD-BT10)

Blue Black

Microphone*

(supplied)

• To avoid the risk of accident and the

potential violation of applicable

laws, this product should never be

used while the vehicle is being dri-

ven except for navigation purposes.

And, also Rear Displays should not

be in a location where it is a visible

distraction to the driver.

• In some countries or states the view-

ing of images on a display inside a

vehicle even by persons other than

the driver may be illegal. Where

such regulations apply they must be

obeyed and this product’s video

source or TV features should not be

used.

English Español Deutsch Français Italiano Nederlands

IP-BUS cable

(supplied)

Dock connector

port

Dock connector

(supplied with iPod adapter)

iPod with

Dock connector

iPod adapter

(e.g. CD-IB100)

(sold separately)

Blue

Black

3 m

Yellow DIGITAL OUT*

G.SP (Guidance speaker output)*

MIC INPUT

The microphone in the voice

recognition kit (e.g. CD-VC1)

(sold separately) is connected

when the voice recognition

function is used.

3 m

30-pin cable

Power cord

WIRED REMOTE INPUT

Please see the Instruction

Manual for the Wired Remote

Control adapters (sold separately).

Display unit

20 cm

EXTENSION port

Not used.

*: This terminal is intended

to support future equip-

ment and should not be

used if you are using

this product by itself.

Connecting the System

Connecting the power cord (1)

Connect leads of the same

colour to each other.

Cap (*1

When not using this terminal,

do not remove the cap. Fuse (10 A)

Yellow

To terminal always supplied

with power regardless of

ignition switch position.

Black (earth)

To vehicle (metal) body.

Bluetooth

adapter

(CD-BT10)

Note:

Depending on the kind of vehicle, the

function of *3 and *5 may be different.

In this case, be sure to connect *2 to *5

and *4 to *3. Fuse (2 A)

)

ISO connector

Yellow (*2)

To terminal always supplied

with power regardless of

ignition switch position.

Red (*4)

To electric terminal controlled

by ignition switch (12 V DC)

ON/OFF.

Yellow (*3)

Back-up

(or accessory)

Red (*5)

Accessory

(or back-up)

Black (earth)

To vehicle (metal) body.

Orange/white

To lighting switch terminal.

Note:

In some vehicles, the ISO connector

may be divided into two. In this case,

be sure to connect to both connectors.

Fuse resistor

Speaker leads

White: Front left +

White/black: Front left ≠

Grey: Front right +

Grey/black: Front right ≠

Green: Rear left +or Subwoofer +

Green/black: Rear left ≠or Subwoofer ≠

Violet: Rear right +or Subwoofer +

Violet/black: Rear right ≠or Subwoofer ≠

Andere Handbücher für AVIC-X1BT

Inhaltsverzeichnis

Sprachen:

Andere Pioneer Auto-Navigationssystem Handbücher

Pioneer

Pioneer AVICF500BT - CD-VM1 Optional Microphone Gebrauchsanweisung

Pioneer

Pioneer AVIC-F20BT Bedienungsanleitung

Pioneer

Pioneer AVIC-Z1000DAB Bedienungsanleitung

Pioneer

Pioneer AVIC-EVO1-OC2-MTB Bedienungsanleitung

Pioneer

Pioneer AVIC-N1 Bedienungsanleitung

Pioneer

Pioneer AVIC-X9115BT Bedienungsanleitung

Pioneer

Pioneer AVIC-HD3 Bedienungsanleitung

Pioneer

Pioneer AVIC-N3 Bedienungsanleitung

Pioneer

Pioneer AVIC-Z2 - Navigation System With DVD player Bedienungsanleitung

Pioneer

Pioneer AVIC-Z920DAB Bedienungsanleitung

Pioneer

Pioneer AVIC-Z6110BT Bedienungsanleitung

Pioneer

Pioneer AVIC-F160-2 Bedienungsanleitung

Pioneer

Pioneer AVIC-Z1 Bedienungsanleitung

Pioneer

Pioneer AVIC-F900BT/XS/RE Bedienungsanleitung

Pioneer

Pioneer T1000-23345 Bedienungs- und Wartungshandbuch

Pioneer

Pioneer AVIC-F850BT Bedienungsanleitung

Pioneer

Pioneer AVIC-80DVD Bedienungsanleitung

Pioneer

Pioneer AVIC-F220 Bedienungsanleitung

Pioneer

Pioneer AVIC-F80BT Bedienungsanleitung

Pioneer

Pioneer AVIC-F980DAB Bedienungsanleitung

Pioneer

Pioneer AVIC-F710BT Bedienungsanleitung

Pioneer

Pioneer AVIC-Z1000DAB Bedienungsanleitung

Pioneer

Pioneer AVICF500BT - CD-VM1 Optional Microphone Bedienungsanleitung

Pioneer

Pioneer CNDV-21 Bedienungsanleitung

Beliebte Auto-Navigationssystem Handbücher anderer Marken

Clarion

Clarion Navigation In-Car Entertainment Bedienungsanleitung

Rosen

Rosen DP-1001 Bedienungsanleitung

Alpine

Alpine INE-W970HD Bedienungsanleitung

Skoda

Skoda AMUNDSEN+ Bedienungsanleitung

Blaupunkt

Blaupunkt TravelPilot DX-N Bedienungsanleitung

Sanyo

Sanyo NVM-4030 - Easy Street - Automotive GPS... Bedienungsanleitung

Kenwood

Kenwood DNN991HD Bedienungsanleitung

AvMap

AvMap Geosat 2C Bedienungsanleitung

Eonon

Eonon GE01B Bedienungsanleitung

Nextar

Nextar M3-MX - Automotive GPS Receiver Bedienungsanleitung

Furrion

Furrion NV2200 Bedienungsanleitung

Mio

Mio MOOV 200-Series Bedienungsanleitung

Prestigio

Prestigio GeoVision 5150 Bedienungsanleitung

Hummer

Hummer 2006 H3 Bedienungsanleitung

Magellan

Magellan Maestro 4210 - Automotive GPS Receiver Konfigurationshandbuch

Garmin

Garmin StreetPilot c510 Bedienungsanleitung

Garmin

Garmin nüvi 2200 Bedienungsanleitung

Garmin

Garmin 2610/2650 Bedienungsanleitung