Planet DHR-800 Bedienungsanleitung

NOVA100 Series

DHR-800

DHR-800P

19" Modular/ Expandable

Dual-Speed Stackable Hub

NOVA100 Series

Trademarks

Contents subject to revision without prior notice.

PLANET is a registered trademark of PLANET Technology Corp. The

information in this manual is subject to change without notice. All

other trademarks belong to their respective owners.

FCC Warning

This equipment generates and uses radio frequency energy. If it

is not installed and used properly in strict accordance with the

manufacturer‘s instructions, it may cause interference to radio

and television reception. It has been type-tested and found to

comply the specifications in sub-part J of Part 15 of FCC Rules,

which are designed to provide reasonable protection against

such interference in a residential installation. There is no

guarantee that interference will not occur in a particular

installation. If this equipment does cause interference to radio or

television reception which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

Re-orient the receiving antenna

•Relocate the computing device with respect to the receiver

•Move the computer away from the deceiver

•Plug the computer into a different outlet so that computer

and receiver are on different electrical circuits.

If necessary the user should consult the dealer or an experienced

radio or television technician for additional suggestions.

Revision

The information in this manual is subject to change without

notice.

User's manual for PLANET Nova 100 Series,

For models: DHR-800/DHR-800P.

Rev 1.20 (Jul. 1998)

Part NO. EMHDHR800v2

iii

Table of Contents

1. INTRODUCTION....................................................................1

ABOUT THIS GUIDE.....................................................................1

CHECKLIST.................................................................................1

PRODUCT FEATURES ...................................................................2

ABOUT FAST ETHERNET..............................................................2

2. INSTALLATION......................................................................5

HARDWARE DESCRIPTION............................................................5

•LED Indication...................................................................6

•Rear Panel .........................................................................7

HARDWARE INSTALLATION..........................................................8

•General Rules.....................................................................8

•Connecting End Nodes .......................................................9

•Stacking two Hubs............................................................11

•Connecting the Hub to Another Hub by Uplink port .........11

•Installing the modules into the Hub ..................................11

•Connecting the Hub to AC Power.....................................12

HARDWARE TROUBLESHOOTING................................................12

APPENDIX A SPECIFICATIONS............................................15

APPENDIX B RJ-45 PIN ASSIGNMENTS...............................16

STRAIGHT-THROUGH /CROSSOVER CABLE.........................16

NOVA100 Series

DHR-800/DHR-800P User’s Manual

Introduction

About This Guide

Thank you for purchasing PLANET NOVA100 10/100Mbps Dual

Speed Ethernet Hub –DHR-800/DHR-800P. Compact in size and

lightweight, utilizing the latest VLSI technology to provide high

reliability levels, the units provide a flexible approach to hub

deployment.

In this user's guide, you will learn product characteristics, it's

features, and also some basic installation concepts. Please read the

following section carefully before your installation.

Checklist

Carefully unpack the package and check its contents against the checklist

given below.

•10/100BASE-TX Dual-Speed Ethernet hub:

Primary Model –DHR-800P

Secondary Model –DHR-800

•User‘s manual

•Power Cord

•Accessories

Please inform your dealer immediately for any wrong, missing, or damaged

part if possible, retain the carton including the original packing materials,

and use them against to repack the product in case there is a need to return

it to us for repair.

NOVA100 Series

Product Features

1. DHR-800P/DHR-800 is a 8-port modularized 19" Rack mount

10/100Mbps Dual Speed Ethernet Stackable Hub, complies with the

IEEE802.3 10Base-T and IEEE802.3u 100Base-TX Class II

standard.

2. DHR-800P and DHR-800 are the same product series and can stack

with each other.

•DHR-800P is the 8-port Dual-Speed Ethernet Hub with internal

switching module –called “Primary Hub”

•DHR-800 is the 8-port Dual-Speed Ethernet Hub without

switching module –called “Secondary Hub”

3. At rear panel, provide two stacking ports for stacking up to 3 units

max. This type of connection has no sacrifice ports.

4. DHR-800P provides switching function to bridge between the

10Base-T segment and 100Base-TX segment.

5. DHR-800 provide two speed auto-negotiation, but 10Base-T and

100Base-TX segments can not communicate with each other, except

by stacking with DHR-800P primary model.

6. At the front panel, one additional RJ-45 Uplink port can be

cascaded to a hub by using straight-through cable.

7. Two Expansion Slots for multiple purpose networking, network

expansion and extension

8. LED indicators array for simple diagnostics and management

About Fast Ethernet

This hub is technically known as a 100Base-TX Class II Fast

Ethernet hub. This Section describes what this means in practical

terms.

•

Ethernet Standards and Operation Speeds

DHR-800/DHR-800P User's 3

The standards of the Ethernet are defined by the Institute of

Electrical and Electronics Engineers (IEEE). The standard for

traditional Ethernet using hubs and twisted-pair cables is known as

10Base-T. Traditional Ethernet works at a signaling speed of

10Mbps, that is, ten megabits (slightly more than a character) per

second. The Base in 10Base-T stands for “baseband,”a one-bit-at-

a-time signaling method; the T stands for twisted-pair cables.

Fast Ethernet was developed to meet the demand for increased

“bandwidth,”in other word, greater data-carrying capacity. A fast

Ethernet hub works at 100Mbps, ten times the speed of a 10Base-T

hub.

The IEEE had defined several Fast Ethernet Standards. The hub complies

with the 100Base-TX standard: 100Mbps baseband signaling on twisted-

pair cables, with signals crossing from the Transmit lines to the Receive

lines somewhere between each pair of communication end nodes.

•

Fast Ethernet Hub Classes

This hub is a Class II Fast Ethernet hub. This means two things:

1.It will work with Fast Ethernet interface cards of one type only, and

2.It can be connected to another hub for the purpose of expanding the

network.

Note: A Class I hub will work with more than one type of Fast Ethernet

interface card, but cannot be connected to another hub.

•

100Base-TX Fast Ethernet Cabling

The twisted-pair cables used for traditional Ethernet and Fast Ethernet all

look the same on the outside. Such cables, however, come in different

grades and with different wire arrangement, and can have different kinds

of sheathing.

NOVA100 Series

The kinds of cables that can be used with a 100Base-TX Class II Fast

Ethernet hub are

♦Category 5 unshielded twisted-pair cable, and ( Category 5 UTP)

♦Type 1 shielded twisted-pair cable (Type 1 STP )

•

100Base-TX Fast Ethernet Summary

Be sure to remember the following rules about a 100Base-TX Class II Fast

Ethernet hub:

1. All end nodes connected to the hub must have 100Base-TX Fast

Ethernet interface cards.

2. Only Category 5 UTP or Type 1 STP cables may be used to connect and

nodes to the hub. The cables must be straight-wired.

3. To expand a network built around one Fast Ethernet hub, you can

connect the hub to one and only one other 100Base-TX Class II hub.

DHR-800/DHR-800P User’s Manual

2. Installation

Hardware Description

This product series provide two different running speed –10Mbps and

100Mbps in the same hub and automatically distinguish the speed of

incoming connection and group the same speed ports in a network segment,

i.e., each port has auto-negotiation Nway function.

Both DHR-800P and DHR-800 products have dual-speed Nway function,

but only DHR-800P with switching function to bridge 10Mbps and

100Mbps segments.

The DHR-800 series product can stack up each other, but in a stack only

ONE DHR-800P primary hub is allowed. It means that in a stack you can

have several DHR-800 hubs then all ports with dual-speed auto sensing

function, but 10Base and 100Base segments can not link together. Now by

adding one DHR-800P hub to this stack, 10 and 100 segments can

communicate through inside switch module.

This section describes the important parts of the 10/100BASE-TX Dual-

Speed Ethernet hub. It presents front panel and rear panel drawings of the

product showing the LED indicators, connectors, and switches.

•

Front panel

The following figure shows the front panel of 8-port 10/100BASE-TX

Dual-Speed Ethernet hub.

Fig 2.1 DHR-800P front panel

Note: The difference between DHR-800 and DHR-800P is on the plastic

NOVA100 Series

label on front panel. The model number and character “Primary”is

for DHR-800P.

There are 8 RJ-45 jacks on the front panel. Each jack is labeled with a port

number.

All ports‘Transmit and Receive lines are crossed within the hub (ie. 1-8

ports are MDI-X ports). A 10/100BASE-TX port must be internally cross-

wired to let you connect an end node using straight-wired cabling.

A special RJ-45 connector is converted from the 1st port as “Uplink”port

(MDI-II port). The “Uplink”port is used for connecting another hub

through an ordinary straight-wired twisted-pair cable by running one end

of straight cable to “Uplink”port and the other end to another hub‘s

normal port.

One expansion slots for optional module installation.

•

LED Indication

On the front panel, there are several LED indicators for monitoring the

device itself, and the network status. At a quick glance of the front panel,

the user would be able to tell if the product is receiving power; if it is

monitoring another hub or concentrator; or if a problem exists on the

network.

The following table describes the function of each LED indicator

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Planet Schalten Handbücher

Planet

Planet FNSW-1601 Bedienungsanleitung

Planet

Planet NOVASwitch FNSW-8086F Bedienungsanleitung

Planet

Planet IGS-5225 Series Bedienungsanleitung

Planet

Planet Switch Bedienungsanleitung

Planet

Planet IKVM-8010 Bedienungsanleitung

Planet

Planet WGSW-2620HP Bedienungsanleitung

Planet

Planet GSD-808HP Bedienungsanleitung

Planet

Planet FNSW-2402 Bedienungsanleitung

Planet

Planet IFB-244-SLC Bedienungsanleitung

Planet

Planet VC24024 Bedienerhandbuch

Planet

Planet GSD-1603 Bedienungsanleitung

Planet

Planet VC-820M Bedienungsanleitung

Planet

Planet WH-2400M Bedienungsanleitung

Planet

Planet IFGS-1022HPT Bedienungsanleitung

Planet

Planet FGSW-2620CS Bedienungsanleitung

Planet

Planet IGS-5225-4T2S Bedienungsanleitung

Planet

Planet NOVASwitch FNSW-8086F Bedienungsanleitung

Planet

Planet SGSW-24040 Bedienungsanleitung

Planet

Planet FSD-805 Bedienungsanleitung

Planet

Planet SGS-5220-24T2X Bedienungsanleitung

Planet

Planet GSD-805 Bedienungsanleitung

Planet

Planet WS-1032P Bedienungsanleitung

Planet

Planet WGSW-20160HP Bedienungsanleitung

Planet

Planet FGSW-2612PVS Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung