Planet GSD-804P Bedienungsanleitung

8-Port 10/100/1000Mbps with 4-Port PoE

Gigabit Ethernet Switch

GSD-804P

User's Manual

Trademarks

Contents subject to revision without prior notice.

PLANET is a registered trademark of PLANET Technology Corp. All other trademarks

belong to their respective owners.

Disclaimer

PLANET Technology does not warrant that the hardware will work properly in all

environments and applications, and makes no warranty and representation, either

implied or expressed, with respect to the quality, performance, merchantability, or

tness for a particular purpose.

PLANET has made every effort to ensure that this User’s Manual is accurate;

PLANET disclaims liability for any inaccuracies or omissions that may have

occurred.

Information in this User’s Manual is subject to change without notice and does not

represent a commitment on the part of PLANET. PLANET assumes no responsibility

for any inaccuracies that may be contained in this User’s Manual. PLANET makes

no commitment to update or keep current the information in this User’s Manual,

and reserves the right to make improvements to this User’s Manual and/or to the

products described in this User’s Manual, at any time without notice.

If you nd information in this manual that is incorrect, misleading, or incomplete,

we would appreciate your comments and suggestions.

FCC Warning

This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with

the Instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at

his own expense.

CE Mark Warning

This is a Class A product. In a domestic environment, this product may cause radio

interference, in which case the user may be required to take adequate measures.

Energy Saving Note of the Device

This power required device does not support Standby mode operation.

For energy saving, please remove the power cable to disconnect the device from

the power circuit.

Without removing power cable, the device will still consuming power from the

power source. In the view of Saving the Energy and reduce the unnecessary power

consuming, it is strongly suggested to remove the power connection for the device

if this device is not intended to be active.

WEEE Warning

To avoid the potential effects on the environment and human health as a

result of the presence of hazardous substances in electrical and electronic

equipment, end users of electrical and electronic equipment should

understand the meaning of the crossed-out wheeled bin symbol. Do not

dispose of WEEE as unsorted municipal waste and have to collect such WEEE

separately.

Revision

PLANET 8-Port 10/100/1000Mbps with 4-Port PoE Gigabit Ethernet Switch User's

Manual For Model: GSD-804P

Revision: 1.0 (May 2011)

Part No.: 2350-A35100-000

Table of Contents

1. Introduction ............................................................................................... 5

1.1 Checklist............................................................................................. 5

1.2 Product Description.............................................................................. 5

1.3 Features ............................................................................................. 5

1.4 Specication........................................................................................ 7

2. Hardware Description .................................................................................. 8

2.1 Front Panel........................................................................................... 8

2.1.1 LED Indicators ............................................................................ 9

2.2 Rear Panel ........................................................................................... 9

3. Hardware Installation .................................................................................10

3.2 Rack Mounting ...................................................................................12

3.3 Product Application............................................................................13

3.3.1 Connecting end node or Switch ..................................................13

3.3.2 Department/ Workgroup PoE Switch............................................14

3.4 Power over Ethernet Powered Device ..................................................15

4. Power over Ethernet Overview...................................................................16

5. Troubleshooting .........................................................................................19

Appendix A Networking Connection ..................................................................20

A.1 Data Out PoE Switch RJ-45 Port Pin Assignments (Port 1 to Port-4)........20

A.2 Switch's RJ-45 Pin Assignments - 1000Mbps, 1000Base-T ......................20

A.3 Switch's RJ-45 Pin Assignments - 10/100Mbps, 10/100Base-TX ..............21

1. Introduction

1.1 Checklist

Check the contents of your package for following parts:

GSD-804P x 1

User's Manual x 1

Power Cord x 1

If any of these pieces are missing or damaged, please contact your dealer

immediately, if possible, retain the carton including the original packing material,

and use them against to repack the product in case there is a need to return it to

us for repair.

1.2 Product Description

To fulll the demand of sufcient PoE power for network applications with Gigabit

speed transmission, the new member in the 802.3af PoE Gigabit Ethernet Switch

family - GSD-804P, the 8-Port 10/100/1000Mbps with 4-Port 802.3af Power over

Ethernet Switch which features high performance Gigabit IEEE 802.3af PoE (Up to

15.4 Watts) and totally 55 Watts PoE budget on half of the 10/100/1000Mbps TP

ports of GSD-804P. The four 802.3af PoE ports provide PoE power injector function

which is able to drive 4 IEEE 802.3af compliant powered devices. The GSD-804P

also provides a simple, cost-effective, and non-blocking wire-speed performance

with 10-inch metal shape for desktop deployment in compact housing, SOHO ofce

or department network application.

All RJ-45 copper interfaces in the GSD-804P support 10/100/1000Mbps Auto-

Negotiation for optimal speed detection through RJ-45 Category 6, 5 or 5e cables.

It also supports standard Auto-MDI/MDI-X that can detect the type of connection

to any Ethernet device without requiring special straight or crossover cables.

1.3 Features

RJ-45 Interface

8-Port 10/100/1000Mbps Gigabit Ethernet portsl

4-Port supports 48V DC power to PoE Powered Devicel

PoE

Complies with IEEE 802.3af Power over Ethernet End-Span PSEl

Up to 4 IEEE 802.3af devices poweredl

Supports PoE Power up to 15.4 Watts for each PoE portl

Auto detect powered device (PD)l

Circuit protection prevents power interference between portsl

Remote power feeding up to 100ml

Switching

Hardware based 10/100/1000Mbps Auto-Negotiation and Auto MDI/MDI-Xl

Flow control for Full Duplex operation and back pressure for Half Duplex oper-l

ation

Integrates address look-up engine, supporting 8K absolute MAC addressesl

9K Jumbo Frame supports at all speed (10/100/1000Mbps)l

Automatic address learning and address agingl

Hardware

10-inch desktop size, rack mountable; 1U heightl

LED indicators for PoE ready and PoE activityl

Optional Rack Ear Accessories Kit for 10-inch cabinet (RKE-10A) and 19-inchl

cabinet (RKE-10B)

1 silent FAN to provide stable and efcient power performancel

Energy-Saving technologyl

Link down power saving

Intelligent scales power based on cable length

1.4 Specication

Model GSD-804P

Hardware Specication

Network Connector 8-Port RJ-45 for 10/100/1000Base-T

PoE Inject Port 4-Port with 802.3af PoE injector function, Port-1 to

Port-4

LED Display

1 Power, 1 FAN Alert LED

1-4 port PoE in-use

1-8 port Speed, LNK/ACT

Switch Architecture Store and Forward switch architecture

MAC Address 8K MAC address table with Auto learning function

Switch Fabric 16Gbps

Switch Throughput 11.9Mpps

Jumbo Packet Size 9K Bytes

Power Requirement AC 100~240V, 50/60Hz, 1.5A

Power Consumption Max. 65 Watts / 221 BTU

Dimension (W x D x H) 217 x 135 x 43 mm

Weight 890g

Power over Ethernet

PoE Standard IEEE 802.3af Power over Ethernet / PSE

PoE Power Supply Type End-Span

PoE Power Output Per Port 48V DC, 350mA . Max. 15.4 Watts

Power Pin Assignment 1/2(+), 3/6(-)

PoE Power Budget 55 Watts

Standard Conformance

EMI Safety FCC Class A, CE

Standard Compliance

IEEE 802.3

IEEE 802.3u

IEEE 802.3ab

IEEE 802.3x

IEEE 802.3af

Ethernet

Fast Ethernet

Gigabit Ethernet

Flow Control

Power over Ethernet

Environment

Operating Environment 0 ~ 50 Degree C

Storage Environment -40 ~ 70 Degree C

Operating Humidity 5 ~ 95%, relative humidity, non-condensing

Storage Humidity 5 ~ 95%, relative humidity, non-condensing

2. Hardware Description

This product provides three different running speeds – 10Mbps, 100Mbps and

1000Mbps in the same switch and automatically distinguishes the speed of

incoming connection.

This section describes the hardware features of GSD-804P. For easier management

and control of the Switch, familiarize yourself with its display indicators, and ports.

Front panel illustrations in this chapter display the unit LED indicators. Before

connecting any network device to the GSD-804P, please read this chapter carefully.

In the following section, the term “Switch” means the Switch device, ie. GSD-

804P; term of “switch” can be any third switches.

2.1 Front Panel

The Front Panel of the GSD-804P PoE Ethernet Switch consists of 8x Auto-Sensing

10/100/1000Mbps Ethernet RJ-45 Ports. The LED Indicators are also located on the

front panel of the GSD-804P.

Figure 2-1: GSD-804P Switch Front Panel

2.1.1 LED Indicators

System

LED Color Function

PWR Green Lights to indicate that the Switch has power.

FAN Alert Orange Lights to indicate that the FAN failure.

Per 10/100/1000Mbps Port

LED Color Function

PoE In-use Orange Lights to indicate the port is providing 48V DC in-line

power. (1-4 ports)

Speed Green

Lit: indicate the Switch is successfully connecting to the

network at 1000Mbps.

Off: indicate that the Switch is successfully connecting

to the network at 10Mbps or 100Mbps.

LNK/ACT Green

Lit: indicate the link through that port is successfully

established.

Blinks to indicate that the Switch is actively sending or

receiving data over that port.

2.2 Rear Panel

The rear panel of the GSD-804P indicates an AC inlet power socket, which accepts

input power from 100 to 240VAC, 50-60Hz. And have a fan hole on the rear panel.

Figure 2-2: GSD-804P Switch Rear Panel

Power

Notice

1. The device is a power-required device, it means, it will not work

till it is powered. If your networks should active all the time,

please consider using UPS (Uninterrupted Power Supply) for your

device. It will prevent you from network data loss or network

downtime.

2. In some area, installing a surge suppression device may also

help to protect your GSD-804P from being damaged by unregu-

lated surge or current to the GSD-804P or the power adapter.

3. Hardware Installation

Before start up

Before your installation, please refer to the followings for your cabling:

10/100/1000Base-T

All 10/100/1000Base-T ports come with Auto-Negotiation capability. They

automatically support 1000Base-T, 100Base-TX and 10Base-T networks. Users

only need to plug a working network device into one of the 10/100/1000Base-T

ports, and then turn on the GSD-804P. The port will automatically runs in 10Mbps,

20Mbps, 100Mbps or 200Mbps and 1000Mbps or 2000Mbps after the negotiation

with the connected device.

Cabling

Each 10/100/1000Base-T ports use RJ-45 sockets - similar to phone jacks - for

connection of unshielded twisted-pair cable (UTP). The IEEE 802.3 / 802.3u

802.3ab Fast / Gigabit Ethernet standard requires Category 5 UTP for 100Mbps

100Base-TX. 10Base-T networks can use Cat.3, 4, 5 or 1000Base-T use 5/5e/6 UTP

(see table below). Maximum distance is 100meters (328 feet).

Port Type Cable Type Connector

10Base-T Cat 3, 4, 5, 2-pair RJ-45

100Base-TX Cat.5 UTP, 2-pair RJ-45

1000Base-T Cat.5/5e/6 UTP, 2-pair RJ-45

Any Ethernet devices like hubs/ PCs can connect to the GSD-804P by using

straight-through wires. The eight-10/100/1000Mbps ports are auto-MDI/MDI-X can

be used on straight-through or crossover cable.

Inhaltsverzeichnis

Andere Planet Schalten Handbücher

Planet

Planet IFB-244-SLC Bedienungsanleitung

Planet

Planet KVM-201 Bedienungsanleitung

Planet

Planet IGS-4215 Series Bedienungsanleitung

Planet

Planet WGSD-1022 Bedienungsanleitung

Planet

Planet FSD-504PE Bedienungsanleitung

Planet

Planet SGSW-24040 Bedienungsanleitung

Planet

Planet GS-5220-8UP2T2X Bedienungsanleitung

Planet

Planet GSW-1602SF Bedienungsanleitung

Planet

Planet IKVM-8020 Bedienungsanleitung

Planet

Planet FNSW-2401CS Bedienungsanleitung

Planet

Planet ISW-511 Series Bedienungsanleitung

Planet

Planet IGS-10020PT Bedienungsanleitung

Planet

Planet WGSW-24040 Bedienungsanleitung

Planet

Planet KVM-800 Bedienungsanleitung

Planet

Planet WGSW-48000 Bedienungsanleitung

Planet

Planet IGS-1020PTF Series Bedienungsanleitung

Planet

Planet FSD-504HP Bedienungsanleitung

Planet

Planet IPM-8221 Bedienungsanleitung

Planet

Planet ISW-800T-M12 Bedienungsanleitung

Planet

Planet GS-4210-8UP2S Bedienungsanleitung

Planet

Planet TSN-6325-8T4S4X Bedienungsanleitung

Planet

Planet MGSW-004 Bedienungsanleitung

Planet

Planet WGS-4215-8P2S Bedienungsanleitung

Planet

Planet GSD-1020 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung