Planet MAP-3120 Programmierhandbuch

Page 1 of 97

802.11a/b/g Outdoor/Indoor Wireless Mesh

Network Access Point

MAP-3020 / MAP-3100 / MAP-3120

Web Management

Configuration Manual

Page 2 of 97

be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or

computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical,

manual or otherwise, without the prior written permission of PLANET.

PLANET makes no representations or warranties, either expressed or implied, with respect to the

contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular

purpose. Any software described in this manual is sold or licensed "as is". Should the programs prove

defective following their purchase, the buyer (and not PLANET, its distributor, or its dealer) assumes

the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting

from any defect in the software. Further, PLANET reserves the right to revise this publication and to

make changes from time to time in the contents hereof without obligation to notify any person of such

revision or changes.

All brand and product names mentioned in this manual are trademarks and/or registered trademarks of

their respective holders.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in

a particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following measures:

1.Reorient or relocate the receiving antenna.

2.Increase the separation between the equipment and receiver.

3.Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

4.Consult the dealer or an experienced radio technician for help.

FCC Caution

To assure continued compliance. (example-use only shielded interface cables when connecting to

computer or peripheral devices). Any changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the Following two

conditions: ( 1 ) This device may not cause harmful interference, and ( 2 ) this Device must accept any

interference received, including interference that may cause undesired operation.

Page 3 of 97

Federal Communication Commission (FCC) Radiation Exposure

Statement

This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In

order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to

the antenna shall not be less than 20 cm (8 inches) during normal operation.

R&TTE Compliance Statement

This equipment complies with all the requirements of DIRECTIVE 1999/5/CE OF THE EUROPEAN

PARLIAMENT AND THE COUNCIL OF 9 March 1999 on radio equipment and telecommunication

terminal Equipment and the mutual recognition of their conformity (R&TTE)

The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications Terminal

Equipment and Satellite Earth Station Equipment) As of April 8,2000.

Safety

This equipment is designed with the utmost care for the safety of those who install and use it. However,

special attention must be paid to the dangers of electric shock and static electricity when working with

electrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed

at all times to ensure the safe use of the equipment.

EU Countries Not Intended for Use

The ETSI version of this device is intended for home and office use in Austria Belgium, Denmark,

Finland, France (with Frequency channel restrictions). Germany, Greece, Ireland, Italy,

Luxembourg .The Netherlands, Portugal, Spain, Sweden and United Kingdom.

The ETSI version of this device is also authorized for use in EFTA member states Iceland,

Liechtenstein, Norway and Switzerland.

Potential Restrictive Use

France: Only channels 10,11,12 and 13

Page 4 of 97

WEEE Regulation

To avoid the potential effects on the environment and human health as a result of the

presence of hazardous substances in electrical and electronic equipment, end users of

electrical and electronic equipment should understand the meaning of the crossed-out

wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and have to

collect such WEEE separately.

Revision

Web Interface User’s Manual for PLANETWireless Mesh Access Point

Model: MAP-3100 / MAP-3120/MAP-3020

Rev: 4.0 (July, 2009)

Part No. EM-MAP3K_webv4.doc

Page 5 of 97

Table of Content

Table of Content 5

1Overview 7

1.1 MAP-3100 Variants 7

1.2 Package Content 7

1.3 Features 8

1.4 Network Topology 9

1.5 Wireless Performance 11

2Hardware Installation 12

2.1 Procedures 12

2.2 Startup the MAP-3100 13

2.3 Startup the MeshAP 14

3Web Based Management 16

3.1 Configuration Menu Overview 16

3.2 System 18

3.2.1 System > System 18

3.2.2 System > Syslog 20

3.2.3 System> Advance 21

3.2.4 System > Profile 23

3.3 Network 24

3.3.1 Network > DNS Setting 24

3.3.2 Network > WAN (MAP-3100 only) 25

3.3.3 Network > VLAN 28

3.3.4 Network > Mesh 31

3.3.5 Network > Wireless 35

3.3.6 Network > Route 38

3.3.7 Network > IPSEC (MAP-3100 only) 40

3.3.8 Network > L2TPC (MAP-3100 only) 41

3.3.9 Network > OLSR (MAP-3100 only) 42

3.4 Service 44

3.4.1 Service > DHCPD (MAP-3100 only) 44

3.4.2 Service > Firewall (MAP-3100 only) 45

3.4.3 Service > MAC Access 47

3.4.4 Service > Virtual Server (MAP-3100 only) 49

3.4.5 Service > NTP 50

3.4.6 Service > Traffic Shaping (MAP-3100 only) 51

3.4.7 Service > PPTP Server (MAP-3100 only) 53

3.4.8 Service > AutoIP (MAP-3100 only) 55

3.4.9 Service > Captive Portal (MAP-3100 only) 56

3.4.10 Service > RADIUS 58

3.4.11 Service > Dynamic DNS 60

Page 6 of 97

3.4.12 Service > Zero Config (MAP-3100 only) 61

3.4.13 Service > Mobile IP (Future Feature for MAP-3100 only) 62

3.4.14 Service > Route Watchdog (MAP-3100 only) 63

3.4.15 Service > System Watchdog 64

3.5 Management 65

3.5.1 Management > HTTPD 65

3.5.2 Management > Configuration 67

3.5.3 Management > SNMPD 69

3.5.4 Management > Firmware 71

3.5.5 Management > Trap 72

3.5.6 Management > User Group (MAP-3100 only) 73

3.5.7 Management > Database (MAP-3100 only) 75

3.5.8 Management > Webspace (MAP-3100 only) 76

3.5.9 Management > Customize Login (MAP-3100 only) 77

3.5.10 Management > NMS Addresses 77

3.5.11 Management > Reboot 79

3.6 Tools 80

3.6.1 Tools > Ping 80

3.6.2 Tools > TFTP 81

3.7 Status 82

3.7.1 Status > Status 82

3.7.2 Status > Interfaces 82

3.7.3 Status > Services 85

3.7.4 Tools > Ifconfig 87

3.7.5 Tools > Route 88

3.7.6 Status > Users (MAP-3100 only) 89

3.7.7 Status > System Log 89

3.7.8 Status > Topology (MAP-3100 only) 90

3.7.9 Status > Mobile IP (MAP-3100 only) 90

3.7.10 Status > Neighbor 91

4Technical Support 92

Appendix A Using the External Login Server 93

Page 7 of 97

1Overview

Thank you for choosing the PLANET MAP-3100/MAP-3120/MAP-3020 Wireless Mesh

Access Point. The MAP-3100 / MAP-3120/MAP-3020 allows a wireless mesh network to be

rapidly deployed with minimal configuration required by the end user. This user’s guide

describes the detailed web interface configuration options.

1.1 MAP-3100 Variants

Currently, there are two MAP-3100 variants available:

MAP-3100: supports both Layer 2 and Layer 3 operations.

MAP-3120/MAP-3020: support Layer 2 operation only.

Throughout the manual, the MAP-3100 will be used to collectively refer to both models.

Where the functionality of the variance, the actual model name will be used.

1.2 Package Content

The MAP-3100 / MAP-3120 following items should be included:

• Indoor Mesh AP x 1

• Power Adapter x 1

• 2.4/5GHz Dipole Antenna x 2

• Quick Start Guide x 1

• Management Utility and User's manual CD x 1

If any of the above items are damaged or missing, please contact your dealer immediately.

The following information , the terms of Mesh AP will mean MAP-3120/MAP-3020. unless it

is specified.

The MAP-3020 following items should be included:

• Outdoor Mesh AP x 1

• Power adapterx1 with Power cord x1

• POE-152-MESH x1

• Mounting kit x1

• 25 Meter cable CAT5 with RJ-45 plug and ODU connector x1

• 1.5 Meter N –type to N type connector cable x2

• Quick Start Guide x 1

• Management Utility and User's manual CD x 1

If any of the above items are damaged or missing, please contact your dealer immediately.

Page 8 of 97

1.3 Features

Dual wireless interfaces for independent Backhaul link and local clients connection

2 x IEEE 802.11a/b/g adapters

2 x reverse SMA connector

Supports full dynamic routing (layer 3) among all node APs (MAP-3100)

OLSR, optimized link state routing protocol

Self-healing and Self-configuration, Plug and Play installation

Supports layer 2 operation (MAP-3100 / MAP-3120/MAP-3020)

Adjustable output power

Central management software

AES backhaul communication

IEEE 802.1q VLAN, multiple VLAN/SSID supports

IEEE 802.1x, IEEE 802.1i WPA/ WPA2, and VPN pass-through mechanisms

Supports Wireless Separation, Watchdog mechanism

QoS for bandwidth control or traffic prioritizing

Supports SNMP v2c, v3

IEEE 802.3af Power over Ethernet capable

Operating temperature: -20~70 degree C (MAP-3020)

IP-68 protection housing (MAP-3020)

Page 9 of 97

1.4 Network Topology

MAP-3100s can be used to create two network topologies: a closed network or an Internet

access network that attaches to a network with connectivity to the Internet.

In a closed network infrastructure, as shown in figure below, all devices are configured to

operate in the same mode (Relay mode). This network configuration is suitable for

applications where the clients using the mesh only need to communicate with each other and

do not need to access the Internet or other remote network resources that are not directly

connected to the mesh.

Page 10 of 97

An Internet access network, as shown in figure below, is typically used to provide Internet

availability to a number of clients that connect to the mesh network. Alternatively, this

configuration can be used to provide access for client devices to remote resources on a

private network. There must be one or more gateway devices in such infrastructure that

provides access from the mesh network to an external network.

Note

1. The MAP-3100 supports 5 operating modes. Three for Layer 3, two for Layer

2. At Layer 3 mode, multiple Gateways are allowed. At Layer 2 mode, only one

Gateway is allowed.

3. At the view of Mesh backhaul network, Layer 2 mode and Layer 3 mode

device can not co-existing to each other.

Andere Handbücher für MAP-3120

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Planet Drahtloser Zugangspunkt Handbücher

Planet

Planet WNAP-1110 Bedienungsanleitung

Planet

Planet WAP-4060PE Bedienungsanleitung

Planet

Planet WAP-3000 Bedienungsanleitung

Planet

Planet WDAP-C7200E Bedienungsanleitung

Planet

Planet WNAP-6350 Bedienungsanleitung

Planet

Planet WNAP-1110 Bedienungsanleitung

Planet

Planet WNAP-6350 Bedienungsanleitung

Planet

Planet WNAP-3000PE Bedienungsanleitung

Planet

Planet WAP-6000 Bedienungsanleitung

Planet

Planet WNAP-W2201A Bedienungsanleitung

Planet

Planet IAP-1800AX Bedienungsanleitung

Planet

Planet WAP-7500 Bedienungsanleitung

Planet

Planet WNAP-W2200UE Bedienungsanleitung

Planet

Planet Network Device WAP5 Bedienungsanleitung

Planet

Planet WNAP-7350 Bedienungsanleitung

Planet

Planet 802.11n Wireless Access Point WNAP-1120 Bedienungsanleitung

Planet

Planet WBS-502AC Bedienungsanleitung

Planet

Planet WAP-4033 Bedienungsanleitung

Planet

Planet WAP-4030A Bedienungsanleitung

Planet

Planet WNAP-7300 Bedienungsanleitung

Planet

Planet IAP-2000PS Bedienungsanleitung

Planet

Planet WAP-4035 Bedienungsanleitung

Planet

Planet WDAP-1750AC Bedienungsanleitung

Planet

Planet WNAP-6305 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung