Plus M-12 Series Benutzerhandbuch

M-12 Series Copyboard / C-12 Series Captureboard

Assembly and Setup Manual

This is the installation and assembly manual for the M-12 series Copyboard and C-12

series Captureboard.

(The copyboard and/or captureboard are referred to as "the set" or "the main unit" in this manual.)

To the Customer

Special skills are required to install the set. Never try to assemble the

set yourself.

To the Dealer or Installation Tradesman

In the interest of the safety of the customer, please perform installation

work paying due attention to the strength of the installation location to

ensure that it can bear the load of the main unit, printer, and installation

parts.

TABLE OF CONTENTS

1. Please Read in the Interest of Safety ....................................................... 2

2. Packaging List ............................................................................................ 3

3. Installation Procedure ............................................................................... 4

4. Assembly of the stand ................................................................................ 4

5. Wall Mounting ............................................................................................. 7

6. Assembly of the Printer Table ................................................................. 10

7. Connection to the set .............................................................................. 12

8. Test Print ................................................................................................... 17

9. Changing the Height of the Unit ............................................................. 18

1. PLEASE READ IN THE INTEREST OF SAFETY

Warning

• If you are not a qualiﬁed assembly serviceperson, do not perform installation procedures.

• Please be sure to perform the installation and assembly based on this manual. Incorrect installation

or assembly will be the cause of injury.

• Please have 2 or more persons lift the main unit when installing or removing it.

Also, be sure to lock the stand's casters before installing or removing. If not, the stand could slip un-

expectedly, resulting in accidents.

• To prevent dropping the strength of the installation location and the anchoring method must fully bear

over a long period the load of the main unit, printer, and installation parts. The installation should also

be performed to fully withstand an earthquake. Incorrect installation can result in the main unit falling

and causing injury.

• Please use M6 or equivalent screws for the wall mounting portion. Use of screws other than M6 or

equivalent can result in the main unit falling and causing injury.

• Please mount to a post in the wall or a sturdy wall stud. When the mounting positions of the main unit

are not reached, please use optional wall support ﬁttings.

• Please use hardware like anchor nuts and anchor bolts for mounting on a concrete wall.

• Be sure to install the stabilizers supplied with the stand at each of the 4 locations (to prevent top-

pling).

• The AC adapter box is for storing the AC power adapters of the main unit and printer. The AC power

adapters and the power cords heat up. Read the "Important Safety Information" in the main unit's

"User's Manual" carefully and store them properly.

CAUTION

• When a printer is mounted on the set, attach the Velcro and printer guides so that the printer does not

slip off. If not, the printer could fall when moving the set, resulting in damage or injury.

* The Velcro is meant to prevent slipping, not to fasten the printer in place.

* Velcro is a registered trademark of Velcro Industries.

The packaged contents will differ depending on the purchased Series.

Please open the carton and check the parts.

In the rare event that something is missing, please contact your store of purchase.

■List of Items in Package

Main unit: 1 unit (standard type or wide type)

Wall mounting brackets: × 4, M4×8 screws × 16 (for wall mounting)

Printer table (1 set): Printer table × 1, Brackets × 2, M4×8 screws × 4, M3×6 screws × 10, Cushions × 2, Printer guides × 2,

Velcro× 2 sets

AC adapter box (1 set): With 2 masking screws

Cable covers for copyboard: Standard type×1, Wide type ×2

AC power adapter (with power code): × 1 (HEC-AP065-24V)

Markers: × 4 (One each of black, red, blue, and green)

Eraser: × 1

USB cable: × 1

Documentation: Instruction manual × 1, CD-ROM × 1, Quick Guide × 1, Assembly and Setup Manual (this manual) × 1

TOOL BOX Software Operation Manual × 1

■Printer package*: One unit

Please check the user’s manual of the printer for a list of contents for the printer package.

2. PACKAGING LIST

■Stand packaging list*

T-shape legs (with casters) × 2, Hexagonal socket screws × 8, Flat washers × 8, Horizontal bars × 2, Hexagonal

wrench × 1, Stay × 1, Nylon bushing × 1, M3×6 screws × 2, Stabilizers × 4, Frame caps × 2, Pipe caps × 4, Lock-

screws × 2, Cable covers for stand × 2 (Standard type × 1, Wide type × 1)

* The printer and stand may be options.

* The stand may be an option.

(Please consult with a dealer or installation tr adesman.Installation work should not be done by the customer.)

4. Assembly of the stand See Page 4

6. Assembly of the printer table See Page 10

7. Connection to the set See Page 12

8. Test print See Page 17

6. Assembly of the printer table See Page 10

7. Connection to the set See Page 12

8. Test print See Page 17

5. Wall mounting See Page 7

The installation method will change depending on the type of installation. Please perform installation and

assembly according to the following procedures.

4. ASSEMBLY OF THE STAND

Frame Cap

Stabilizer

T-shape leg

• Diagrams of printers that appear in this manual are representative illustrations.

The illustration will differ from the actual printer. Check the owner's manual of your printer for information about the names of

the connectors and their locations and use.

Caster

Stabilizer

Use the same method to assemble the left and

right sides of the stand.

(1) Press-ﬁt the frame cap onto the top

of the T-shaped legs.

(2) Attach the stabilizers to the front

and back of the T-shaped legs.

Insert the stabilizers securely all the way in.

(3) Lock the caster stoppers.

Press the bottom portion of the stoppers to lock

them.

CAUTION

To prevent toppling, be sure to install the stabiliz-

ers at each of the 4 locations. The toppling of this

machine could cause bodily injury or damage the

machine.

3. INSTALLATION PROCEDURE

Note

* The printer may be sold separately.

(4) Attach the two horizontal bars to the

T-shape legs.

Use hexagonal socket screws (M5) and flat wash-

ers (M5) to attach.

Partially fasten using the hexagonal wrench (M5), then

tighten securely after the upper and lower horizontal

bars have been attached.

(5) Place the stand’s hooks in the

mounting holes in the support fit-

tings and insert the grooves in the

hooks securely.

There are 3 hole positions. By changing the position,

the installation height can be changed among 3 lev-

els in 100 mm units (1770, 1870, and 1970 mm (the

maximum height)).

(6) Mount the printer table to the main

unit.

See Page 10 for information about the assembly and

installation of the printer table.

* Installation of the printer table is not required when

the main unit is used only for USB memory stor-

age.

Hexagonal wrench (M5)

T-shaped leg

Horizontal bar

Hexagonal socket screw (M5)

Flat washer (M5)

CAUTION

Please have 2 or more persons lift the main unit

when installing it or making a height adjustment. If

the unit is dropped or falls over, this could cause

unforeseen injury.

Check that the hook is securely inserted into the

installation hole. Insecure installation could result

in the unit falling and causing bodily injury or dam-

age to the unit.

Mounting hole

Hook

The rear

frame

4. ASSEMBLY OF THE STAND

(7) Install the stay to the printer table.

Insert the nylon bushing into the stay.

Insert the stay into the pipe of the stand.

Mount the stay to the printer table using two M3 screws.

Check again that the grooves in the stand’s hooks are se-

curely inserted in the mounting holes in the support ﬁttings.

(8) Lock the main unit and stand with the two

locking knobs.

Stay Pipe

M3 screws

Locking knobs

Stay

Nylon bushing

Notice

4. ASSEMBLY OF THE STAND

1077 mm

1200 mm

1077 mm

1200 mm





(1) Determining the installation location

The diagram indicates the dimensions of the installa-

tion positions. The installation position is the same for

both the standard type and the wide type.

The installation of the main unit to the wall is per-

formed after the printer table is assembled and at-

tached to the main unit. See Page 10.

• When the Wall Is Concrete

Embed the commercially available anchor bolts or

anchor nuts for M6 at the installation positions. (See

below)

• When the Wall Structure Is Plywood or

Plaster Board, etc.

Please check that a post or stud is located at the

installation position indicated by the dimensions.

When a post is not located at the target installation

position, please use a wall support fitting that is

available separately. Attach a wall support ﬁtting to

the post or stud.

• When the building does not have posts, please

use the stand.

• Separate optional items are available when the

standard wall mounting is not possible, or when

installation will be made to a partition.

Stud, etc.

Wooden Walls Wood screws

Make a suitable hole with an auger and

 attach the Copyboard with wood screws.

Concrete Walls Anchors

Make a base hole in the wall with a drill. Insert the anchor. Fasten the main

unit with screws.

Please use a drill of the hole diameter speciﬁed for the anchor.

Steel Walls Phillips head tapping screws (Pan head)

Check that the steel wall is reinforced and use a drill a hole of suit-

able diameter, then attach the main unit with tapping screws.

Reference: Installation Method for Various Wall Materials

Please perform an installation that suits the wall material.

Please install the main unit to posts or studs when the wall surface is of insufﬁcient strength.

Installation Wall Material Installation Method





5. WALL MOUNTING

Note



(3) Attach the 4 supplied wall-mount brackets to the main unit using M4×8 screws.

Four screws for each bracket. (Total 16 screws.)

(2) Stick the cushions on the printer table, then mount the printer table on the main

unit.

 Peel off the protective sheets from the cushions’ adhesive surfaces.

Stick the cushions (2) on the back of the bracket.

See page 10 for instructions on assembling and mounting the printer table.

When mounting the printer table after installing the main unit on a wall, see page 10.

* There is no need to mount the printer table when only storing data in the USB memory storage.

Protective sheet on

adhesive surface

Cushion

Cushions

Back of bracket





Wall-mount bracket

M4 x 8 screw

5. WALL MOUNTING

(4) Attaching and anchoring the main unit to a wall or wall support ﬁtting.

(The anchoring method will differ depending on the wall mounting method.)

Installing on a Concrete Wall

Anchor nut, etc.

M6 screw

Mounting to a Post

M6 wood screw

5. WALL MOUNTING

Printer Table Right-side Installation Printer Table Left-side Installa-

The printer table can be installed at either the left or right side. The installation method is the same.

Determine whether to install the printer table on the left or right side in consideration of the position of the

power outlet in the wall, etc.

The method of assembling the printer table is the same for stand placement and for wall mounting. The assembly diagrams

omit the stand.

M4 X 8 screws

(1) Temporarily fasten the right and left brackets to the main unit using four M4×8

screws in the order of Steps to .

Right bracket

Left bracket

M4x8

screws

Front screw

hole

Front screw

hole

When mounting the printer table after

installing the main unit on a wall

Use four M4×8 screws to temporarily fasten the

left and right brackets to the four holes in the

bottom of the main unit.

Screws hole

Screws hole Screws hole

Screws hole

(2) Temporarily fasten the printer table to the

brackets with six M3 x 6 screws.

M3 x 6 screw

Printer table

M3 x 6 screw

6. ASSEMBLY OF THE PRINTER TABLE

If the printer touches the wall, move the printer

table forward, then fasten it in place using four

M3x6 screws.

* When installing using a stand, do not move the printer table

forward and fasten it in place. Doing so could result in the

printer table falling.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Beliebte Whiteboard Handbücher anderer Marken

Copernicus

Copernicus RC105 Bedienungsanleitung

IKEA

IKEA MALA 104.889.67 Bedienungsanleitung

SMART

SMART SBX800 Bedienungsanleitung

SMART

SMART Board MX V3 Series Bedienungsanleitung

funtronic

funtronic EasyBoard Bedienungsanleitung

Best-Rite

Best-Rite Baby Folding Wheasel 784-T Bedienungsanleitung

Best-Rite

Best-Rite Modular Room Divider Bedienungsanleitung

IKEA

IKEA MALA 504.565.92 Bedienungsanleitung

Panasonic

Panasonic TX-47P800HQ TX-47P800HZ Bedienungsanleitung

SMART

SMART ST442i Bedienungsanleitung

Quartet

Quartet QRT-72981 Bedienungsanleitung

SMART

SMART Smart Board 480 Bedienungsanleitung

EGAN

EGAN GlassWrite TableScreen TSG Bedienungsanleitung

Claridge

Claridge Edify Mobile Bedienungsanleitung

Legamaster

Legamaster e-Board Touch 2 Bedienungsanleitung

Nureva

Nureva WALL Bedienungsanleitung

Best-Rite

Best-Rite Black Splash Bedienungsanleitung

Da-Lite

Da-Lite Cosmopolitan Electrol Bedienungsanleitung