Politec NAT SENSOR Handbuch
PRODUCT
NAT
NAT SENSOR
Product code NAT SENSOR
INDOOR AND OUTDOOR CURTAIN SENSOR
INSTALLATION AND MOUNTING MANUAL VERSION 2.1
Table of contents
2
NAT SENSOR POLITEC | INSTALLATION MANUAL - VER.2.1
1.Introduction…………………………………………………………………………………………………………………………….……...3
2.Product description……………………………………………………………………………………………...............……………..3
3.General warnings………………………………………………………………………………………………………………...……..…. 4
3.1 Additional warnings for devices powered by mains voltage
3.2 Installation warnings
4.List of main components …………………………………………………………………………………………….........…………..5
5.Preparation for installation .................................................. ...............................................................6
5.1 Preparation of the sensor parts before installation
5.2 It is advisable to carry out
6.Placement and installation ………………………………………………………………………………………………….…..........7
6.1 Placement and installation height
6.2 Anti-crawl
6.3 Pet Immunity
6.4 Type of detection
6.5 Wrong installations
7.Mounting ................................................................................................................................................9
7.1 Direct wall mounting
7.2 Wall mounting with canopy
7.3 Mounting with L-shaped bracket
7.4 Mounting with L-shaped bracket and with canopy
7.5 Mounting with NAT BR bracket (Accessory)
8.Circuit board…………….…………………………………………….………………………………………………………..........……..15
9.Component description…..……………………………………………………………………………………….………………….....16
9.1 Terminal board
9.2 Examples of balancing
9.3 DIP functionality
9.4 LED indicators
9.5 Adjustment trimmer
10.Description of functions ……………………………………………………....…………....…........................................19
11.PIR LIMITER ………………..…………………………………………………………………………………………...……………........19
11.1 Application
11.2 PIR LIMITER mounting
12.Installation examples..……………………………………………………………………………………………....………….………21
13.Technical specifications ………………………………………………………………………………………………………..……….23
14.Product disposal………………………………………………………………………………………….……....................………..24
1.Introduction
3
NAT SENSOR POLITEC | INSTALLATION MANUAL - VER.2.1
Congratulations on having purchased a Politec curtain sensor.This appliance guarantees long-
lasting and reliable operation if installed correctly.For correct and effective use, it is necessary to
read this instruction manual carefully.
The system has been designed to detect intrusions and activate the alarm; it is not a
device that prevents intrusion.Politec is not responsible for damage, injury or loss
caused by accidents, theft, force majeure (including momentary lightning-induced
overcurrent), abuse, improper or incorrect use, faulty installation or inadequate
maintenance.
2. Product description
This curtain sensor has been designed for the protection of entrances (doors and windows) both
for outdoor and indoor use.
Thanks to its small size, it is particularly suitable for protecting doors, windows and shop
windows and, thanks to the materials used and advanced technology, it can be used in any
outdoor installation where it is necessary to protect well-defined areas.
In order to ensure correct performance, it must be installed on the upper part of the window,
door, or French window to detect the movement of a stranger through the entrance.
Before installation, check the following conditions:
•the wall must not have depressions or excessive protrusions;
•avoid positioning the detector near heat sources or in direct sunlight;
•avoid the reflection of electromagnetic energy on large surfaces such as, for example, mirrors,
metal walls, etc .;
•avoid pointing the detector at fluorescent lamps or placing it in their immediate vicinity.
If installed outdoors it must be sheltered (not completely exposed to the elements).
Warnings
Mounting, installation of the sensor and connection to the mains must be carried out
by expert and qualified personnel, in compliance with rules and regulations applicable
to electrical systems.
3.General warnings
4
NAT SENSOR POLITEC | INSTALLATION MANUAL - VER.2.1
This installation manual contains important information regarding safety for installation: it is
necessary to read all the instructions before proceeding with the installation.
Keep this manual for future use.
•If you have any questions or doubts during installation, do not carry out any operations and contact
the support service.
•Use of these products for purposes other than those specified in these instructions is prohibited.
•You must not make any change to the components of the product unless stated in the manual in
order not to void the warranty; such operations can only lead to malfunctions; Politec assumes no
liability for malfunctions or damage due to modified products.
•Depending on the specific situation of use, check for the need for additional devices: detectors or
signalling devices.
•During installation, mounting and use of the product, make sure no foreign objects (solids, metals
or liquids) are able to penetrate inside the open devices.
•Manufacturer's liability:Politec assumes no liability for failures resulting from incorrect installation;
lack of maintenance, incorrect assembly or use.
•Politec is also not liable for incorrect or incomplete operation of the product or failure to detect
intrusion.
•Warranty (summary of conditions):Politec guarantees its products for a period of 2 years from the
production date.The warranty is applied to those purchasing directly from Politec; there is no
warranty for the end user who, in the event of breakdowns or faults, must contact the installer or
dealer.
•The warranty excludes aesthetic parts as well as parts subject to normal wear and parts subject to
normal consumption such as batteries and accumulators.
3.1 Additional warnings for devices powered by mains voltage
This manual is intended only for technical personnel qualified to install such devices.
•Assessing the hazards that may occur during installation and use of the system, in order to achieve
complete safety, it is necessary that installation takes place in full compliance with applicable laws,
methods, rules and regulations.
•Before accessing the internal terminals of the product, it is necessary to disconnect all the power
circuits.
•If automatic circuit breakers or fuses trip, before resetting them it is necessary to identify the fault
and repair it.
3.2 Installation warnings
•Check that all the material to be used is in excellent condition and suitable for use.
•Before proceeding with the installation, check the environmental class of the products in the
"technical specifications" chapter.
•Check, comparing with the values shown in the paragraph "technical specifications", that the range
of the devices is correct
•Check that the sensor is positioned in areas protected against potential impact, in flat areas and on
fixed supports to avoid movements.
•Do not place the system components close to heat sources as they could be damaged.
•Each sensor has its own operating principle: check the instructions for choosing the right position in
the respective instruction manual.
4.List of main components
5
NAT SENSOR POLITEC | INSTALLATION MANUAL - VER.2.1
The package contains the following components and accessories.
When opening the package, check that everything has been included.
No.
COMPONENT
1
Cover
2
PIR LIMITER
3
Circuit board
4
Gasket
5
Base
6
Concentric seals
7
Metal plate
8
Canopy
9
L
-shaped bracket
1
2
3
4
6
7
8
59
5.Preparation for installation
6
NAT SENSOR POLITEC | INSTALLATION MANUAL - VER.2.1
5.1 Preparation of the sensor parts before installation
Since the communication of the sensors (depending on the family) to the control unit can take place
by wire, via wireless, it is advisable to firstly check all the components of the sensors and their possible
accessories before beginning the installation.
5.2 It is advisable to carry out:
•device configuration on a table;
•checking device operation
•the permanent fixing of each device;
•the preparation and carrying out of electrical connections.
In order to avoid errors, operating and installation problems, it is advisable to proceed as follows:
a) Place all the products with the package open on a table;
b) For the low-consumption sensor version for wireless models with universal circuit board housing,
insert and connect the radio transmitter, and connect it to the sensor
c) Power the sensors and program them
d) Test sensor operation;
e) Place (without fixing) the sensors in the planned points;
f) Place (without fixing) all the other devices at the planned points;
g) Check for each sensor that there is sufficient field for radio communication (for wireless versions);
h) Permanently fix the sensors.
Before proceeding with the installation, it is necessary to check the integrity of the product, the
adequacy of the model chosen and the suitability of the environment intended for installation:
• Check that all conditions of use fall within the "limits of use" and in the "Technical specifications of
the product".
• Check that the environment chosen for the installation is compatible with the total footprint of the
product.
• Check that the surface chosen for the installation of the product is sturdy so as to ensure stable
fixing and that it is adequately protected against possible impacts or the elements.
6.Placement and installation
7
NAT SENSOR POLITEC | INSTALLATION MANUAL - VER.2.1
6.1 Placement and installation height
Position the sensor considering the type of surrounding environment and the protection
distance for correct and effective operation.
Position it in such a way that there are no obstacles in its range of action (trees/plants or
objects that can swing or move with the wind or rain if installed outside).
Position the sensor so that sunlight does not hit it directly near the sensors.
SIDE VIEW
VIEW FROM ABOVE
6.2 Anti-crawl
If mounted at a height of less than 3m, the system can also detect the areas underneath the NAT
sensor by suitably adjusting the sensitivity of the two technologies.This is thanks to the inclination
present on the microwave board and PIR which generate an anti-crawl zone.This solution allows you
to limit the detection area even without the use of a bracket.
N.B.:The detection zone can vary according to the installation height and the surrounding
environment
6.3 Pet Immunity
If mounted at a height between 2 and 3m, the sensor manages to identify a pet with a mass not
exceeding 10 kg that walks within the detection area.
8
NAT SENSOR POLITEC | INSTALLATION MANUAL - VER.2.1
6.4 Type of detection
The sensor is designed for detecting actual crossing of the curtain and not just approaching
it.The detection zone is based on the mass of a person of about 70 kg.The sensor could detect
objects of higher mass (such as cars, trucks, etc.) having a mass significantly higher than the
expected area.
6.5 Wrong installations
The sensor can detect objects such as cars and/or trucks beyond the detection area, therefore
avoid installing the sensor facing a vehicle passageway or use the bracket and tilt the sensor
downwards in order to reduce the field of view.Avoid the presence of plants, air conditioners
and mobile objects in the detection area
10m
9
NAT SENSOR POLITEC | INSTALLATION MANUAL - VER.2.1
7.1 Direct wall mounting
In any case, it is necessary to take into consideration the specific beam diffusion of each model, to
avoid reflection of the beams caused by the ground or by adjacent objects.
WARNING:
Product warranty is invalid if there is any hole in the sensor or any component
1.Insert the shielded alarm cable in the fixing
plate;
Fix the plate to the wall;
2.Drill the rubber grommet and slip in the
cable;
Screw the base onto the plate;
Fix the NAT board on the support base and
carry out the wiring;
3.After the wiring and the functional test, close
the NAT making sure that the gaskets and ORs
are present and not deteriorated to guarantee
the integrity of the product
7.Mounting
10
NAT SENSOR POLITEC | INSTALLATION MANUAL - VER.2.1
7.2 Wall mounting with canopy
In any case, it is necessary to take into consideration the specific beam diffusion of each model, to
avoid reflection of the beams caused by the ground or by adjacent objects.
1.Insert the shielded alarm cable in the upper
hole of the canopy;
Open the central slots and fix the canopy to
the wall
2.Drill the rubber grommet and slip in the
cable.
Insert the hook of the Nat base in the
canopy compartment as shown in the
figure and then fix it with the screw
located at the bottom
3.Screw the base onto the canopy;
Fix the NAT board on the support base and carry
out the wiring;
Andere Handbücher für NAT SENSOR
1
Inhaltsverzeichnis
Andere Politec Zubehör Handbücher
