Porter-Cable H1000 Bedienungsanleitung

Generator

Instruction

manual

To learn more about Porter-Cable

visit our website at:

http://www.porter-cable.com

The Model and Serial No. plate is located on the frame. Record these

numbers in the spaces below and retain for future reference.

Model No.

Type

Serial No.

ESPAÑOL: PÁGINA 23

FRANÇAIS: PAGE 45

IMPORTANT

Please make certain that the person who is to use this equipment

carefully reads and understands these instructions before starting

operations.

Model

H1000

PROFESSIONAL POWER TOOLS

2 — ENG

This product is not equipped with a spark arresting muffler. If the product will be used around

flammable materials, or on land covered with materials such as agricultural crops, forest, brush, grass, or

other similar items, then an approved spark arrester must be installed and is legally required in the state of

California. It is a violation of California statutes section 130050 and/or sections 4442 and 4443 of the Cal-

ifornia Public Resources Code, unless the engine is equipped with a spark arrestor, as defined in section

4442, and maintained in effective working order. Spark arresters are also required on some U. S. Forest

service land and may also be legally required under other statutes and ordinances.

This product may contain chemicals known to the state of California to cause cancer, birth defects, or other

reproductive harm. This warning is given in compliance with California Proposition 65, as detectable

amounts of chemicals subject to proposition 65 may be contained in this product.

•

SPECIFICATION

MODEL H1000

HORSE POWER 20

RATED/SURGE WATTS 10000/12500

VOLTAGE 120/240

AMPERAGE 83.3A/41.7A

PHASE SINGLE

HERTZ 60 Hz

ENGINE SPEED 3600 RPM

MAX. AMBIENT TEMP. 104° F

FUEL CAPACITY 7 GALLON

RUN TIME @ 50%/100% 9.9/4.9 HRS

3 — ENG

WARRANTY

Porter-Cable Corporation

4825 Highway 45 North

P.O. Box 2468

Jackson, TN 38302-2468

1-888-559-8550

PORTER-CABLE CORPORATION warrants to the original purchaser that each new electric generator and service part is

free from defects in material and workmanship, and agrees to repair or replace under this warranty any defective product or

part as follows from the original date of purchase.

2 YEARS – Limited warranty on electric generator alternators and 1 year limited warranty on all other parts.

90 Days – Service parts

Engine warranties are the responsibility of the engine manufacturer. Warranties of merchandise sold by Porter-Cable which

has been manufactured by and identified as the product of another company are the responsibility of the manufacturer of

that product.

THIS WARRANTY IS NOT TRANSFERABLE AND DOES NOT COVER

Products sold damaged or incomplete, sold “as is,” sold reconditioned, or used as rental equipment.

Delivery, installation, or normal adjustments explained in the owner’s manual.

Damage or liability caused by shipping, improper handling, improper installation, improper maintenance, improper

modification, or the use of accessories and/or attachments not specifically recommended by PORTER-CABLE for the

product.

Repairs necessary because of operator abuse or negligence, or the failure to install, operate, maintain, and store the

product according to the instructions in the owner’s manual.

Damage caused by cold, heat, rain, excessive humidity, corrosive environments and materials, or other contaminants.

Expendable items that become worn during normal use such as fuel filters, air cleaners, spark plugs, and engine oil.

Cosmetic defects that do not interfere with product functionality.

Freight costs from customer to Porter-Cable.

Repair and transportation costs of products or parts determined not to be defective.

ANY INCIDENTAL, INDIRECT OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT FROM

ANY DEFECT, FAILURE OR MALFUNCTION OF THE PRODUCT. Some states do not allow the exclusion or limitation

of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PUR-

POSE, ARE LIMITED TO ONE YEAR FROM THE DATE OF ORIGINAL PURCHASE. Some states do not allow

limitations on how long an implied warranty lasts, so the above limitations may not apply to you.

WARRANTY SERVICE is available by delivering or shipping the defective product or part to any Porter-Cable authorized

warranty service location. To determine the nearest authorized warranty service location, call the toll free number, 1-888-

559-8550, 24 hours a day, 7 days a week. Specific instructions regarding servicing arrangements and scheduling may vary

depending on the type and size of the product and the availability of repair parts.

DO NOT return the defective product to the retailer.

Retain the original cash register sales receipt as proof of purchase for warranty work.

Purchasers should contact Porter-Cable directly if they do not receive satisfactory results from the authorized warranty

service center.

4 — ENG

Attempting to connect generator

directly to the electrical system of

any building structure.

Back feeding electricity through a

building’s electrical system to the out-

side utility feed lines could en-danger

repair persons attempting to restore

service.

Never backfeed electricity through

a structure's electrical system.

HAZARD HOW TO PREVENT ITWHAT COULD HAPPEN

RISK OF ELECTROCUTION AND FIRE

When using this product basic pre cautions should always be

followed including the following:

• SAVE THESE INSTRUCTIONS •

IMPORTANT SAFETY INSTRUCTIONS

SAFETY GUIDELINES - DEFINITIONS

Information that you should pay special

attention to.

This manual contains information that

is important for you to know and un-

derstand. This information relates to

protecting YOUR SAFETY and PRE-

VENTING EQUIPMENT PROB-

LEMS. To help you recognize this

information, we use symbols to the

right. Please read the manual and pay

attention to these sections.

URGENT SAFETY INFORMATION - A HAZARD

THAT WILL CAUSE SERIOUS INJURY OR

LOSS OF LIFE.

IMPORTANT SAFETY INFORMATION - A

HAZARD THAT MIGHT CAUSE SERIOUS

INJURY OR LOSS OF LIFE.

Information for preventing damage to

equipment.

To connect to a structure's electri-

cal system in a safe manner,

always have a Double-Throw

Transfer Switch installed by a qual-

ified electrician and in compliance

with local ordinances. (When in-

stalling a Double-Throw Transfer

Switch, a minimum of 10 gauge

wiring must be used.)

Attempting to connect to the incom-

ing utility service could result in elec-

trocution.

Restoration of electrical service while

the generator is connected to the

incoming utility could result in a fire or

serious damage if an isolator switch is

not installed.

Failure to use a double throw transfer

switch when connecting to a struc-

ture's electrical system can damage

appliances and WILL VOID the

manufacturer's warranty.

5 — ENG

READ AND UNDERSTAND ALL WARNINGS BEFORE

ATTEMPTING TO OPERATE GENERATOR.

RISK OF ELECTROCUTION AND FIRE (cont’d)

HAZARD HOW TO PREVENT ITWHAT COULD HAPPEN

Operation of generator in rain, wet,

icy, or flooded conditions.

Water is an excellent conductor of

electricity! Water which comes in

contact with electrically charged com-

ponents can transmit electricity to the

frame and other surfaces, resulting in

electrical shock to anyone contacting

them.

Operate generator in a clean, dry,

well ventilated area. Make sure

hands are dry before touching

unit.

Use of worn, damaged, undersized

or ungrounded extension cords.

Placing generator on or against

highly conductive surface, such as

a steel walkway or metal roof.

Improper connection of items to

generator.

Operation of unit when damaged,

or with guards or panels removed.

Contact with worn or damaged exten-

sion cords could result in electrocu-

tion.

Use of undersize extension cords

could result in overheating of the

wires or attached items, resulting in

fire.

Use of ungrounded cordsets could

prevent operation of circuit breakers

and result in electrical shock.

Accidental leakage of electrical

current could charge conductive

surfaces in contact with the generator.

Exceeding the load capacity of the

generator by attaching too many

items, or items with very high load

ratings to it could result in overheat-

ing of some items or their attachment

wiring resulting in fire or electrical

shock.

Attempting to use the unit when it has

been damaged, or when it is not func-

tioning normally could result in fire or

electrocution.

Removal of guarding could expose

electrically charged components and

result in electrocution.

Inspect extension cords before

use and replace with new cord if

required.

Use proper size (wire gauge)

cordset for application see chart

in the Assembly section of this

manual.

Always use a cordset having a

grounding wire with an

appropriate grounding plug. DO

NOT use an ungrounded plug.

Place generator on low conductiv-

ity surface such as a concrete

slab.

ALWAYS operate generator a min-

imum of six feet from any conduc-

tive surface.

Do not operate generator with

protective guarding removed.

Read the load rating chart and in-

structions in the Wattage Calcula-

tion section. Make sure that the

summation of electrical loads for

all attachments does not exceed

the load rating of the generator.

Do not operate generator with

mechanical or electrical problem.

Have unit repaired by an Autho-

rized Service Center.

6 — ENG

READ AND UNDERSTAND ALL WARNINGS BEFORE

ATTEMPTING TO OPERATE GENERATOR.

RISK OF FIRE

HAZARD HOW TO PREVENT ITWHAT COULD HAPPEN

Attempting to fill the fuel tank while

the engine is running.

Sparks, fire, hot objects

Improper storage of fuel

Inadequate ventilation for genera-

tor

Tampering with factory set engine

speed settings.

Overfilling the fuel tank – fuel spill-

age.

Gasoline and gasoline vapors can

become ignited by coming in contact

with hot components such as the

muffler, engine exhaust gases, or from

an electrical spark.

Cigarettes, sparks, fires, or other hot

objects can cause gasoline or gaso-

line vapors to ignite.

Improperly stored fuel could lead to ac-

cidental ignition. Fuel improperly se-

cured could get into the hands of chil-

dren or other unqualified persons.

Materials placed against or near the

generator or operating the generator in

areas where the temperature exceeds

104° F. ambient (such as storage rooms

or garages) can interfere with its prop-

er ventilation features causing over-

heating and possible ignition of the

materials or buildings.

Engine speed has been factory set to

provide safe operation. Tampering with

the engine speed adjustment could re-

sult in overheating of attachments and

could cause a fire.

Spilled fuel and its vapors can become

ignited from hot surfaces or sparks.

Turn engine off and allow it to cool

before adding fuel to the tank.

Equip area of operation with a fire

extinguisher certified to handle

gasoline or fuel fires.

Add fuel to tank in well ventilated

area. Make sure there are no

sources of ignition near the gener-

ator.

Store fuel in a OSHA approved

container designed to hold

gasoline. Store container in secure

location to prevent use by others.

Operate generator in a clean, dry,

well ventilated area a minimum of

four feet from any building, object

or wall. DO NOT OPERATE UNIT

INDOORS OR IN ANY

CONFINED AREA.

Never attempt to “speed-up” the

engine to obtain more perfor-

mance. Both the output voltage

and frequency will be thrown out of

standard by this practice,

endangering attachments and the

user.

Use care in filling the tank to

avoid spilling fuel. Make sure fuel

cap is secured tightly and check

engine for fuel leaks before

starting engine. Move generator

away from refueling area or any

spillage before starting engine.

Allow for fuel expansion. Keep

maximum fuel level 1/2 inch below

the tip of the fuel tank. Never

refuel with the engine running.

7 — ENG

READ AND UNDERSTAND ALL WARNINGS BEFORE

ATTEMPTING TO OPERATE GENERATOR.

RISK OF BREATHING - INHALATION HAZARD

Operate generator in clean, dry,

well ventilated area. Never operate

unit in enclosed areas such as

garages, basements, storage,

sheds, or in any location occupied

by humans or animals. Keep chil-

dren, pets and others away from

area of operating unit.

Breathing exhaust fumes will cause

serious injury or death.

Gasoline engines produce toxic car-

bon monoxide exhaust fumes.

HAZARD HOW TO PREVENT IT

WHAT COULD HAPPEN

Risk of Injury and Property Damage When

Transporting Generator

If generator is equipped with a fuel

shut-off valve, turn the valve to the

off position before transporting to

avoid fuel leaks. If generator is not

equipped with a fuel shut-off valve,

drain the fuel from tank before

transporting. Transport fuel only in

an OSHA approved container.

Always place generator on a

protective mat when transporting

to protect against damage to

vehicle from leaks. Remove

generator from vehicle immediately

upon arrival at your destination.

Fuel or oil can leak or spill and could

result in fire or breathing hazard, seri-

ous injury or death can result. Fuel or

oil leaks will damage carpet, paint or

other surfaces in vehicles or trailers.

Fire, Inhalation, Damage to Vehicle

Surfaces

HAZARD HOW TO PREVENT IT

WHAT COULD HAPPEN

8 — ENG

HAZARD HOW TO PREVENT ITWHAT COULD HAPPEN

During operation, touch only the con-

trol surfaces of the generator. Keep

children away from the generator at all

times. They may not be able to recog-

nize the hazards of this product.

Contact with hot surfaces, such as en-

gines exhaust components, could result in

serious burns.

Contact with hot engine and generator

components.

RISK OF HOT SURFACES

READ AND UNDERSTAND ALL WARNINGS BEFORE

ATTEMPTING TO OPERATE GENERATOR.

Always use a U.L. listed voltage sensi-

tive surge protector to connect volt-

age sensitive appliances (TV, comput-

er, stereo, etc.). Failure to use a U.L.

listed voltage surge protector will

void the warranty on your genera-

tor.

Notice: A multiple outlet strip is not a

surge protector. Make sure you use a

U.L. listed voltage surge protector.

Any gasoline operated household generator

will incur voltage variations causing damage

to voltage sensitive appliances or could

result in fire.

Operation of voltage sensitive appli-

ances without a voltage surge protec-

tor.

RISK OF UNSAFE OPERATION

HAZARD HOW TO PREVENT ITWHAT COULD HAPPEN

Generator will not operate properly and

will cause damage to the generator and

could cause serious injury or death to you

or others.

Operating generator while suspended Never operate generator while sus-

pended or in an unlevel position.

Always operate generator on a flat,

level surface.

Operation of generator in careless

manner.

All sources of energy include the potential

for injury. Unsafe operation or mainte-

nance of your generator could lead to

serious injury or death to you or others.

• Review and understand all of the

operating instructions a

warnings in this manual.

• Become familiar with the opera-

tion and controls of the

generator. Know how to shut it

off quickly.

• Equip area of operation with a

fire extinguisher certified to

handle gasoline or fuel fires.

• Keep children or others away

from the generator at all times.

9 — ENG

RISK FROM LIFTING

HAZARD HOW TO PREVENT IT

WHAT COULD HAPPEN

The generator is too heavy to be

lifted by one person. Obtain assis-

tance from others before you try to

move it.

Serious injury can result from attempt-

ing to lift too heavy an object.

Lifting a very heavy object.

READ AND UNDERSTAND ALL WARNINGS BEFORE

ATTEMPTING TO OPERATE GENERATOR.

RISK OF MOVING PARTS

HAZARD HOW TO PREVENT ITWHAT COULD HAPPEN

Never operate generator with guard-

ing or cover plates removed. Avoid

wearing loose fitting clothing or jewel-

ry which could be caught by moving

parts.

The generator contains parts which rotate

at high speed during operation. These

parts are covered by guarding to prevent

injury.

Contact with moving parts can result in

serious injury.

RISK OF BURN-EXPLOSION HAZARD

Wear NIOSH approved goggles

and protective gloves when

handling battery.

Explosive chemicals can cause

blindness,serious injury, or death.

Sulfuric acid is a flammable and

explosive chemical that is harmful to

the skin, eyes, and clothing.

HAZARD HOW TO PREVENT IT

WHAT COULD HAPPEN

Keep sparks, flame, cigarettes, or

anything flammable away from

battery.

EXTERNAL: Flush with water

EYES: Flush with water for 15

minutes and get prompt medical

attention.

Chemicals come in contact with

eyes or skin.

Chemicals are ingested.

Chemicals can cause blindness,

serious injury, or death.

Ingested chemicals can cause

serious injury or death.

INTERNAL: Drink large quantities

of water or milk. Follow with Milk

of Magnesia, beaten eggs, or

vegetable oil. Call physician

immediately.

1. Lift the gas tank end of generator and slide 2x4

between generator and pallet as shown.

The generator is too heavy

to be lifted by one person.

Obtain assistance from others before lifting.

2. Place handle grips on handle assemblies.

3. Place one 5/8” washer into the bottom of each end

cap. Push end caps onto the end of the handle

assemblies.

4. Attach handle assemblies to frame using four screws

and flange nuts. NOTE: Screw on outside of frame.

NOTE: Do not tighten until all screws and flange nuts are

assembled.

5. Lift generator and remove 2x4.

10 — ENG

ASSEMBLY

Read this manual. Do not

attempt to operate

equipment until you have read this Manual for

Safety, Operation, and Maintenance Instructions.

NOTE: Left and right describes the location of a part with

the operator facing the outlet panel.

UNPACKING

1. Locate the parts carton and set aside for later use.

2. Cut wire ties holding generator to pallet and remove

protective wrapping.

3. Remove all packaging, leaving generator on pallet.

IMPORTANT: DO NOT remove generator from pallet.

4. Discard all packaging.

Wire Tie

Protective

Wrapping

ASSEMBLE WHEEL KIT

Tools needed:

2 - 2x4 at least 30” long

1 - 1/2” socket

1 - 1/2” open end wrench

1 - hammer

1 - pliers

Parts bag contains:

2 - Handle Grips

2 - Handle End Caps

4 - Screws, .313-18X1.75

1 - Cotter Pin

2 - Washers, 5/8" X 1.32 X .09

1 - Flat Steel Washer

2 - Axle Spacer

2 - Cap Screw 5/16-18 X 3/4

6 - Flange Nuts

2 - Wheel Brackets

1 - 5/8” Axle Cap

2x4

Screws and

Flange Nuts

Gas Tank

Handle Grip

End Cap

5/8” Washer

Handle

Assembly

Inhaltsverzeichnis

Andere Porter-Cable Tragbarer Generator Handbücher

Porter-Cable

Porter-Cable DBSI325 Bedienungsanleitung

Porter-Cable

Porter-Cable D28362-031-0 Bedienungsanleitung

Porter-Cable

Porter-Cable D21679-008-0 Bedienungsanleitung

Porter-Cable

Porter-Cable generator H650IS-W Bedienungsanleitung

Porter-Cable

Porter-Cable PCG2200 Bedienungsanleitung

Porter-Cable

Porter-Cable DBSI325 Bedienungsanleitung

Porter-Cable

Porter-Cable H1000IS-W Bedienungsanleitung

Porter-Cable

Porter-Cable D26779-028-0 Bedienungsanleitung

Porter-Cable

Porter-Cable D29851-038-0 Bedienungsanleitung

Porter-Cable

Porter-Cable D28733-034-0 Bedienungsanleitung

Porter-Cable

Porter-Cable D26981-028-0 Bedienungsanleitung

Porter-Cable

Porter-Cable CH350IS Bedienungsanleitung

Porter-Cable

Porter-Cable DTE325 Bedienungsanleitung

Porter-Cable

Porter-Cable BSI525 Bedienungsanleitung

Porter-Cable

Porter-Cable D27245-028-0 Bedienungsanleitung

Porter-Cable

Porter-Cable H1000IS Bedienungsanleitung

Porter-Cable

Porter-Cable D26860 Bedienungsanleitung

Porter-Cable

Porter-Cable D29833-038-0 Bedienungsanleitung

Porter-Cable

Porter-Cable A02871-043-0 Bedienungsanleitung

Porter-Cable

Porter-Cable H450IS Bedienungsanleitung

Porter-Cable

Porter-Cable CH250 Bedienungsanleitung

Porter-Cable

Porter-Cable BSI550 Bedienungsanleitung

Porter-Cable

Porter-Cable DBSI325-1 Bedienungsanleitung

Porter-Cable

Porter-Cable BSV550-W Bedienungsanleitung

Beliebte Tragbarer Generator Handbücher anderer Marken

Kohler

Kohler 20EORZ Bedienungsanleitung

Powerhorse

Powerhorse 83171 Bedienungsanleitung

HURST

HURST ML-630-SI Bedienungsanleitung

ETQ

ETQ TG4000 Bedienungsanleitung

Briggs & Stratton

Briggs & Stratton 40265 Einrichtungshandbuch

ConMed

ConMed 7550 Bedienungsanleitung

Owon

Owon Waveform Generator Bedienungsanleitung

evertz

evertz 7700 Series Bedienungsanleitung

Power Stroke

Power Stroke PS906025 Bedienungsanleitung

Firefly

Firefly Cygnus CYG2400/460/24 Bedienungsanleitung

Draper

Draper PG950S Firmware-Update

PowerBoss

PowerBoss PowerBoss Bedienungsanleitung

SDMO

SDMO SH 4000 Bedienungsanleitung

EINHELL

EINHELL STE 5500 Bedienungsanleitung

Wanco

Wanco WI3000P Bedienungsanleitung

Full Boar

Full Boar FBT-3300 Bedienungsanleitung

Dwyer Instruments

Dwyer Instruments ASG Bedienungsanleitung

Westinghouse

Westinghouse WH1000i Series Bedienungsanleitung