Power Fist 8663783 Bedienungsanleitung

V4.0 8663783

Please read and understand all instructions before use. Retain this manual for

future reference.

User Manual

12in.ViseMountBox/Pan

MetalBrake

8663783 12 in. Vise Mount Box/Pan Metal Brake V4.0

2 For technical questions call 1-800-665-8685

SPECIFICATIONS

Material Steel

Bend Radius 90 to 170°

Max. Width 12 in.

Max. Capacity 18 Gauge

INTRODUCTION

The Vise Mount Box/Pan Metal Brake permits precision bends in metal sheets up to

18 gauge thick.

SAFETY

WARNING! Read and understand all instructions before using this tool. The

operator must follow basic precautions to reduce the risk of personal injury

and/or damage to the equipment.

Keep this manual for safety warnings, precautions, operating or inspection and

maintenance instructions.

HAZARD DEFINITIONS

Please familiarize yourself with the hazard notices found in this manual. A notice

is an alert that there is a possibility of property damage, injury or death if certain

instructions are not followed.

DANGER! This notice indicates an immediate and specific hazard that will result in

severe personal injury or death if the proper precautions are not taken.

WARNING! This notice indicates a specific hazard or unsafe practice that

could result in severe personal injury or death if the proper

precautions are not taken.

12in.ViseMountBox/Pan

MetalBrake

V4.0 12 in. Vise Mount Box/Pan Metal Brake 8663783

Visit www.princessauto.com for more information 3

CAUTION! This notice indicates a potentially hazardous situation that may result

in minor or moderate injury if proper practices are not taken.

NOTICE! This notice indicates that a specific hazard or unsafe practice will

result in equipment or property damage, but not personal injury.

WORK AREA

1. Operate in a safe work environment. Keep your work area clean, well-lit

and free of distractions.

2. Keep anyone not wearing the appropriate safety equipment away from the

work area.

3. Store unused tools properly in a safe and dry location to prevent rust or

damage. Lock tools away and keep out of the reach of children.

PERSONAL SAFETY

WARNING! Wear personal protective equipment approved by the Canadian

Standards Association (CSA) or American National Standards Institute (ANSI).

PERSONAL PROTECTIVE EQUIPMENT

1. Always wear impact safety goggles that provide front and side protection

for the eyes. Eye protection equipment should comply with CSA Z94.3-07

or ANSI Z87.1 standards based on the type of work performed.

2. Wear gloves that provide protection based on the work materials or to

reduce the effects of tool vibration.

3. Wear protective clothing designed for the work environment and tool.

4. Non-skid footwear is recommended to maintain footing and balance in the

work environment.

5. Wear steel toe footwear or steel toe caps to prevent a foot injury from

falling objects.

PERSONAL PRECAUTIONS

Control the tool, personal movement and the work environment to avoid

personal injury or damage to tool.

1. Do not operate any tool when tired or under the influence of drugs, alcohol

or medications.

8663783 12 in. Vise Mount Box/Pan Metal Brake V4.0

4 For technical questions call 1-800-665-8685

2. Avoid wearing clothes or jewelry that can become entangled with the

moving parts of a tool. Keep long hair covered or bound.

3. Do not overreach when operating a tool. Proper footing and balance

enables better control in unexpected situations.

SPECIFIC SAFETY PRECAUTIONS

WARNING! DO NOT let comfort or familiarity with product (gained from

repeated use) replace strict adherence to the tool safety rules. If you use

this tool unsafely or incorrectly, you can suffer serious personal injury.

1. Use the correct tool for the job. This tool was designed for a

specific function. Do not modify or alter this tool or use it for

an unintended purpose.

2. The workpiece edges may be sharp or have metal slivers protruding from it

after bending. Wear heavy duty gloves when handling the workpiece.

UNPACKING

WARNING! Do not operate the tool if any part is missing. Replace the

missing part before operating. Failure to do so could result in a malfunction

and personal injury.

Remove the parts and accessories from the packaging and inspect for damage.

Make sure that all items in the parts list are included.

ASSEMBLY & INSTALLATION

Numbered references in parenthesis (#1) refer to the included Parts List.

Dashed numbers in parenthesis (Fig. 1-1) refer to a specific point in an

illustration or image.

1. Insert the hand brake into the vise. The

main body (#1) flange fits between the

vise jaws. Close the vise jaws to lock

the hand brake in place.

2. Insert the handle (Fig. 1-2) into the

eccentric shaft (Fig. 1-1) opening.

Tighten the handle.

Fig. 1

V4.0 12 in. Vise Mount Box/Pan Metal Brake 8663783

Visit www.princessauto.com for more information 5

INSTALLING THE DIES

1. Remove the 12 screws (#14) with a hex wrench and then the pressing

plate (#3) from the main body (#1).

2. Select the appropriate dies (#6 to 9) according to the workpiece’s width.

3. Place the dies on the lip of the main body and place the pressing plate on top.

4. Insert the screws. Check that the die edges are even and level with each

other. Adjust if there is a differences. Tighten the screws.

OPERATION

1. Mark the workpiece where you want to bend it.

2. Place the workpiece into the main body slot (Fig. 2).

3. Align the mark on the workpiece with

the front edge of the dies (Fig. 2-2).

4. Pull the handle (Fig. 2-1) down until the

workpiece is at the desired angle.

5. Push the handle back to the upright

position and remove the workpiece.

CARE & MAINTENANCE

1. Maintain the tool with care. A tool in good condition is efficient, easier to

control and will have fewer problems.

2. Inspect the tool components periodically. Repair or replace damaged or

worn components. Only use identical replacement parts when servicing.

3. Follow instructions for lubricating and changing accessories. Lubricate the

rotating parts of the mechanism with a lightweight oil daily.

4. Only use accessories intended for use with this tool.

5. Keep the tool handles clean, dry and free from oil/grease at all times.

WARNING! Only qualified service personnel should repair the tool. An

improperly repaired tool may present a hazard to the user and/or others.

Fig. 2

8663783 12 in. Vise Mount Box/Pan Metal Brake V4.0

6 For technical questions call 1-800-665-8685

DISPOSAL

Recycle a tool damaged beyond repair at the appropriate facility.

TROUBLESHOOTING

Visit a Princess Auto Ltd. location for a solution if the tool does not function

properly or parts are missing. If unable to do so, have a qualified technician

service the tool.

V4.0 12 in. Vise Mount Box/Pan Metal Brake 8663783

Visit www.princessauto.com for more information 7

PARTS BREAKDOWN

PARTS LIST

# DESCRIPTION QTY

1 Main Body 1

2 The Base of Braking 1

3 Pressing Plate 1

4 Eccentric Shaft 1

5 Left Support 1

6 Upper Braking Die 1 in. 1

7 Upper Braking Die 2 in. 1

8 Upper Braking Die 3 in. 1

9 Upper Braking Die 6 in. 1

10 Hex Wrench 6mm 1

11 Handle 1

12 Handle Knob 1

13 Right Support 1

14 Screw M8X20 18

15 Spring Washer 8mm 12

16 Elastic Cylindrical Pin Φ

5X30

17 Screw M6X12 2

8663783 12 in. Vise Mount Box/Pan Metal Brake V4.0

8 For technical questions call 1-800-665-8685

V 4,0 8663783

Vous devez lire et comprendre toutes les instructions avant d'utiliser l'appareil.

Conservez ce manuel afin de pouvoir le consulter plus tard.

Manuel d'utilisateur

Freindemétalàboîte/bac

pourétaude12po

8663783 Frein de métal à boîte/bac pour étau de 12 po V 4,0

2 En cas de questions techniques, appelez le 1-800-665-8685

SPÉCIFICATIONS

Matériau Acier

Rayon de cintrage 90 à 170 °

Largeur max. 12 po

Capacité max. 18 gauge

INTRODUCTION

La boîte de montage de l’étau et le frein de métal permettent de cintrer avec

précision la tôle jusqu’au calibre 18.

SÉCURITÉ

AVERTISSEMENT ! Veuillez lire et comprendre toutes les instructions avant

d'utiliser cet outil. L'utilisateur doit respecter les précautions de base

lorsqu'il utilise cet outil afin de réduire le risque de blessure ou de

dommage à l'équipement.

Conservez ce manuel qui contient les avertissements de sécurité, les

précautions, les instructions de fonctionnement ou d'inspection et d'entretien.

DÉFINITIONS DE DANGER

Veuillez-vous familiariser avec les avis de danger qui sont présentés dans ce

manuel. Un avis est une alerte indiquant qu'il existe un risque de dommage à la

propriété, de blessure ou de décès si on ne respecte pas certaines instructions.

DANGER ! Cet avis indique un risque immédiat et particulier qui

entraînera des blessures corporelles graves ou même la

mort si on omet de prendre les précautions nécessaires.

Freindemétalàboîte/bac

pourétaude12po

Inhaltsverzeichnis

Sprachen:

Andere Power Fist Werkzeuge Handbücher

Power Fist

Power Fist 8089591 Bedienungsanleitung

Power Fist

Power Fist 8438806 Bedienungsanleitung

Power Fist

Power Fist 8665549 Bedienungsanleitung

Power Fist

Power Fist 8074668 Bedienungsanleitung

Power Fist

Power Fist 9166695 Bedienungsanleitung

Power Fist

Power Fist 8517393 Bedienungsanleitung

Power Fist

Power Fist 8823494 Bedienungsanleitung

Power Fist

Power Fist 8916793 Bedienungsanleitung

Power Fist

Power Fist 8885642 Bedienungsanleitung

Power Fist

Power Fist Air Hammer Bedienungsanleitung

Power Fist

Power Fist 8502494 Bedienungsanleitung

Power Fist

Power Fist 8603094 Bedienungsanleitung

Power Fist

Power Fist 8655888 Bedienungsanleitung

Power Fist

Power Fist 8549024 Bedienungsanleitung

Power Fist

Power Fist 8774465 Bedienungsanleitung

Power Fist

Power Fist 8843617 Bedienungsanleitung

Power Fist

Power Fist 1/2 in. Air Ratchet and Socket Set Bedienungsanleitung

Power Fist

Power Fist 8814436 Bedienungsanleitung

Power Fist

Power Fist 8536773 Bedienungsanleitung

Power Fist

Power Fist 9011438 Bedienungsanleitung

Power Fist

Power Fist 8887408 Bedienungsanleitung

Power Fist

Power Fist 8685042 Bedienungsanleitung

Power Fist

Power Fist 8536609 Bedienungsanleitung

Power Fist

Power Fist 8957425 Bedienungsanleitung

Beliebte Werkzeuge Handbücher anderer Marken

Martor

Martor SECUNORM 175 Bedienungsanleitung

ERKCO

ERKCO 1000 Bedienungsanleitung

jbc

jbc N4473 Bedienungsanleitung

FEINMETALL

FEINMETALL FZWZ-SET-001 Bedienungsanleitung

Worx Professional

Worx Professional Sonicrafter WU676 Bedienungsanleitung

Gage Bilt

Gage Bilt GB713SH Bedienungsanleitung

Hilti

Hilti DX 9-ENP Bedienungsanleitung

norbar

norbar NORTRONIC 34399 Bedienungsanleitung

BGS technic

BGS technic 8578 Bedienungsanleitung

Makita

Makita DHR241 Bedienungsanleitung

Motor Guard

Motor Guard JMB-1250 Bedienungsanleitung

Power Adhesives

Power Adhesives 805-12 Bedienungsanleitung

Clemco

Clemco 24189 Bedienungsanleitung

VVG

VVG VNG 903 Series Bedienungsanleitung

Hilti

Hilti FX 3-A Bedienungsanleitung

Grizzly

Grizzly H6472 Bedienungsanleitung

axing

axing BWZ 5-02 Bedienungsanleitung

Dh-Robotics

Dh-Robotics RGI-100 Anleitung zur Verwendung