PowerWalker VFI 1000-3000 CG PF1 Bedienungsanleitung

PowerWalker VFI 1000-3000 CG PF1

Uninterruptible Power Supply System

Version: 1.3

Table of Contents

1. Important Safety Warning ................................................................................... 1

1-1. Transportation .................................................................................................... 1

1-2. Preparation ........................................................................................................ 1

1-3. Installation......................................................................................................... 1

1-4. Operation........................................................................................................... 1

1-5. Maintenance, service and faults........................................................................... 2

2. Installation and setup .......................................................................................... 4

2-1. Rear panel view.................................................................................................. 4

2-2. Operating principle ............................................................................................. 5

2-3. Install the UPS (Only for RT Models).................................................................... 6

2-4. Setup the UPS.................................................................................................... 6

2-5. Battery Replacement (Only for RT Models) ......................................................... 10

2-6. Battery Kit Assembly (option for RT Models)....................................................... 11

3. Operations .......................................................................................................... 13

3-1. Button operation .............................................................................................. 13

3-2. LCD Panel ........................................................................................................ 13

3-3. Audible Alarm................................................................................................... 15

3-4. LCD display wordings index............................................................................... 15

3-5. UPS Setting...................................................................................................... 16

3-6. Operating Mode Description .............................................................................. 21

3-7. Faults Reference Code....................................................................................... 22

3-8. Warning indicator ............................................................................................. 22

4. Troubleshooting..................................................................................................23

5. Storage and Maintenance................................................................................... 24

6. Specifications .....................................................................................................25

1. Important Safety Warning

Please comply with all warnings and operating instructions in this manual strictly. Save this

manual properly and read carefully the following instructions before installing the unit. Do not

operate this unit before reading through all safety information and operating instructions

carefully.

1-1. Transportation

Please transport the UPS system only in the original package to protect against shock

and impact.

1-2. Preparation

Condensation may occur if the UPS system is moved directly from cold to warm

environment. The UPS system must be absolutely dry before being installed. Please

allow at least two hours for the UPS system to acclimate the environment.

Do not install the UPS system near water or in moist environments.

Do not install the UPS system where it would be exposed to direct sunlight or near

heater.

Do not block ventilation holes in the UPS housing.

1-3. Installation

Do not connect appliances or devices which would overload the UPS system (e.g.

laser printers) to the UPS output sockets.

Place cables in such a way that no one can step on or trip over them.

Do not connect domestic appliances such as hair dryers to UPS output sockets.

The UPS can be operated by any individuals with no previous experience.

Connect the UPS system only to an earthed shockproof outlet which must be easily

accessible and close to the UPS system.

Please use only VDE-tested, CE-marked (or UL-marked for 100/110/115/120/127 VAC

models) mains cable (e.g. the mains cable of your computer) to connect the UPS

system to the building wiring outlet (shockproof outlet).

Please use only VDE-tested, CE-marked (or UL-marked for 100/110/115/120/127 VAC

models) power cables to connect the loads to the UPS system.

When installing the equipment, it should ensure that the sum of the leakage current

of the UPS and the connected devices does not exceed 3.5mA.

Temperature Rating - Units are considered acceptable for use in a maximum ambient

of 40°C (104°F).

For Pluggable Equipment - The socket-outlet shall be installed near the equipment

and shall be easily accessible.

1-4. Operation

Do not disconnect the mains cable on the UPS system or the building wiring outlet

(shockproof socket outlet) during operations since this would cancel the protective

earthing of the UPS system and of all connected loads.

The UPS system features its own, internal current source (batteries). The UPS output

sockets or output terminals block may be electrically live even if the UPS system is not

connected to the building wiring outlet.

In order to fully disconnect the UPS system, first press the OFF/Enter button to

disconnect the mains.

Prevent no fluids or other foreign objects from inside of the UPS system.

1-5. Maintenance, service and faults

The UPS system operates with hazardous voltages. Repairs may be carried out only

by qualified maintenance personnel.

Caution - risk of electric shock. Even after the unit is disconnected from the mains

(building wiring outlet), components inside the UPS system are still connected to the

battery and electrically live and dangerous.

Before carrying out any kind of service and/or maintenance, disconnect the batteries

and verify that no current is present and no hazardous voltage exists in the terminals

of high capability capacitor such as BUS-capacitors.

Only persons are adequately familiar with batteries and with the required

precautionary measures may replace batteries and supervise operations.

Unauthorized persons must be kept well away from the batteries.

Caution - risk of electric shock. The battery circuit is not isolated from the input

voltage. Hazardous voltages may occur between the battery terminals and the

ground. Before touching, please verify that no voltage is present!

Caution - Do not dispose of batteries in a fire. The batteries may explode.

Caution - Do not open or mutilate batteries. Released electrolyte is harmful to the

skin and eyes. It may be toxic.

Batteries may cause electric shock and have a high short-circuit current. Please take

the precautionary measures specified below and any other measures necessary when

working with batteries:

a) Remove watches, rings, or other metal objects.

b) Use tools with insulated handles.

c) Wear rubber gloves and boots.

d) Do not lay tools or metal parts on top of batteries.

e) Disconnect charging source and load prior to installing or maintaining the

battery.

f) Remove battery grounds during installation and maintenance to reduce

likelihood of shock. Remove the connection from ground if any part of the

battery is determined to be grounded.

When changing batteries, install the same number and same type of batteries or

battery packs.

Manufacture

Type

Rated

Toplite (Guangzhou)

Technology Battery Co Ltd

(MH29104)

NPW45-12

12 V dc, 9.0 Ah

UXW460-12

12 V dc, 9.0 Ah

NPW36-12

12 V dc, 7.2 Ah

UXW360-12

12 V dc, 7.2 Ah

NPW45-12 FR

12 V dc, 7.0 Ah

UXW460-12/FR

12 V dc, 7.0 Ah

NPW36-12 FR

12 V dc, 7.0 Ah

CSB Battery Co Ltd

(MH14533)

UXW360-12/FR

12 V dc, 7.0 Ah

GP1272

12 V dc, 7.2 Ah

UPS 12460 F2

12 V dc, 9.0 Ah

UPS 12360 6

12 V dc, 6.5 Ah

UPS 12360 7

12 V dc, 6.5 Ah

HR 1234W

12 V dc, 8.5 Ah

HR 1234W FR

12 V dc, 8.5 Ah

Yuasa Battery (Guangdong)

Co Ltd (MH29616)

NPW45-12

12 V dc, 8.0 Ah

NPW45-12FR

12 V dc, 8.0 Ah

For UPS with internally mounted battery

a) Instructions shall carry sufficient information to enable the replacement of the

battery with a suitable manufacturer and catalogue number.

b) Safety instructions to allow access by Service Personnel shall be stated in the

installation/service handbook.

c) If batteries are to be installed by Service Personnel, instructions for

interconnections, including terminal torque, shall be provided.

Do not attempt to dispose of batteries by burning them. This could cause battery

explosion.

Do not open or destroy batteries. Escaping electrolyte can cause injury to the skin

and eyes. It may be toxic.

Please replace the fuse only with the same type and amperage in order to avoid fire

hazards.

Do not dismantle the UPS system.

WARNING: This is a category C2 UPS product. In a residential environment, this

product may cause radio interference, in which case the user many be required to

take additional measures. (only for 220/230/240 VAC system)

Only for 110/120 VAC system:

NOTE: This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference

in which case the user will be required to correct the interference at his own expense.

WARNING: Changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to operate the equipment.

2. Installation and setup

NOTE: Before installation, please inspect the unit. Be sure that nothing inside the package is

damaged. Please keep the original package in a safe place for future use.

2-1. Rear panel view

Tower Models

IEC Type

1K/1.5K 2K 3K

NEMA Type

1K/1.5K 2K 3K

RT Models

IEC Type NEMA Type

1. Programmable outlets: connect to non-critical loads.

2. Output receptacles: connect to mission-critical loads.

3. AC input

4. Network/Fax/Modem surge protection

5. USB communication port

6. RS-232 communication port

7. SNMP intelligent slot

8. Emergency power off function connector (EPO)

9. External battery connection

2-2. Operating principle

The operating principle of the UPS is shown as below

EMI/RFI

Filters

Battery

Charger Battery

DC-to-DC

Converter

Inverter

Rectifier

/PFC

Input Output

The UPS is composed of mains input,

EMI/RFI filters, rectifier/PFC,

inverter, battery charger, DC-to-DC

converter, battery, dynamic bypass and

UPS output.

Dynamic

Bypass

The UPS is composed of mains input, EMI/RFI filters, rectifier/PFC, inverter, battery charger,

DC-to-DC converter, battery, dynamic bypass and UPS output.

1K/

1.5K

2-3. Install the UPS (Only for RT Models)

For safety consideration, the UPS is shipped out from factory without connecting battery wires.

Before install the UPS, please follow below steps to re-connect battery wires first.

Step 1

Step 2

Step 3

Remove front panel.

Connect the AC input and

re-connect battery wires.

Put the front panel back to the

unit.

This UPS can be either displayed on the desk or mounted in the 19” rack chassis. Please choose

proper installation to position this UPS.

Rack-mount Installation

Step 1 Step 2

Tower Installation

Step 1

Step 2

Step 3

2-4. Setup the UPS

Before installing the UPS, please read below to select proper location to install UPS.

1. UPS should be placed on the flat and clean surface. Place it in an area away from vibration,

dust, humidity, high temperature, flammable liquids, gases, corrosive and conductive

contaminants. Install the UPS indoors in a clean environment, where it is away from

window and door. Maintain minimum clearance of 100mm in the bottom of the UPS to

avoid dust and high temperature.

2. Maintain an ambient temperature range of 0ºC to 45ºC for UPS optimal operation. For

every 5ºC above 45ºC, the UPS will derate 12% of nominal capacity at full load. The

highest working temperature requirement for UPS operation is 50ºC.

3. It’s required to maintain maximum altitude of 1000m to keep UPS normal operation at full

load UPS. If it’s used in high altitude area, please reduce connected load. Altitude derating

power with connected loads for UPS normal operation is listed as below:

4. Place UPS:

It’s equipped with fan for cooling. Therefore, place the UPS in a

well-ventilated area. It’s required to maintain minimum clearance of 100mm in the

front of the UPS and 300mm in the back and two sides of the UPS for heat dissipation and

easy-maintenance.

5. Connect to External Battery Pack

When connecting external battery packs, please be sure to connect polarity correctly. Connect

positive pole of battery pack to positive pole of external battery connector in UPS and negative

pole of battery pack to negative pole of external battery connector in UPS. Polarity

misconnection will cause UPS internal fault. It’s recommended to add one breaker between

positive pole of battery pack and positive pole of external battery connector in UPS to prevent

damage to battery packs from internal fault.

The required specification of breaker: voltage ≧1.25 x battery voltage/set; current ≧50A

Please choose battery size and connected numbers according to backup time requirement and

UPS specifications. To extend battery lifecycle, it’s recommended to use them in the

temperature range of 15ºC to 25ºC.

Step 1: External battery connection

Follow the right chart to make external battery connection.

Step 2: UPS input connection

Plug the UPS into a two-pole, three-wire, grounded receptacle only. Avoid using extension

cords.

For 200/208/220/230/240VAC models:

The power cord is supplied in the UPS package.

For 100/110/115/120/127VAC models: The power cord is attached to the UPS. The input

plug is a NEMA 5-15P for 1K and 1.5K models, NEMA 5-20P for 2K model and NEMA 5-30P

for 3K model.

Note: Check if the site wiring fault indicator lights up in LCD panel. It will be illuminated when

the UPS is plugged into an improperly wired utility power outlet (Refer to Troubleshooting

section). Please also check if there is a circuit breaker against overcurrent and short circuit

between the mains and AC input of the UPS for safety operation. The recommended protection

value as following:

For 200/208/220/230/240VAC models: 10A for the 1K and 1.5K models, 16A for the 2K

and 3K models.

For 100/110/115/120/127VAC models: 15A for the 1K and 1.5K models, 20A for 2K model

and 30A for 3K model.

Step 3: UPS output connection

There two kinds of outputs: programmable outlets and general outlets. Please connect

non-critical devices to the programmable outlets and critical devices to the general outlets.

During power failure, you may extend the backup time to critical devices by setting shorter

backup time for non-critical devices.

Step 4: Communication connection

Communication port:

USB port RS-232 port Intelligent slot

To allow for unattended UPS shutdown/start-up and status monitoring, connect the

communication cable one end to the USB/RS-232 port and the other to the communication

port of your PC. With the monitoring software installed, you can schedule UPS

shutdown/start-up and monitor UPS status through PC.

The UPS is equipped with intelligent slot perfect for either SNMP or AS400 card. When

installing either SNMP or AS400 card in the UPS, it will provide advanced communication and

monitoring options.

Inhaltsverzeichnis

Andere PowerWalker UPS Handbücher

PowerWalker

PowerWalker VI 1000RT/LE Bedienungsanleitung

PowerWalker

PowerWalker VFI 1000RM LCD Bedienungsanleitung

PowerWalker

PowerWalker VI 400 SC Bedienungsanleitung

PowerWalker

PowerWalker VFD 400 IEC Bedienungsanleitung

PowerWalker

PowerWalker PF 1 6K Bedienungsanleitung

PowerWalker

PowerWalker VFI 10-200K CPT 3/3 Bedienungsanleitung

PowerWalker

PowerWalker Basic VI SB Series Bedienungsanleitung

PowerWalker

PowerWalker VI 400 Bedienungsanleitung

PowerWalker

PowerWalker VFI 6000 CT LCD Bedienungsanleitung

PowerWalker

PowerWalker Basic VI 3000 STL Bedienungsanleitung

PowerWalker

PowerWalker VI 650 GX Bedienungsanleitung

PowerWalker

PowerWalker VFI 1000 CRM Bedienungsanleitung

PowerWalker

PowerWalker VFI 2000 RMG/S PF1 Bedienungsanleitung

PowerWalker

PowerWalker VFI 1000RM Bedienungsanleitung

PowerWalker

PowerWalker VI CSW Series Bedienungsanleitung

PowerWalker

PowerWalker VFI 1000 Bedienungsanleitung

PowerWalker

PowerWalker VI 2000 LCD Bedienungsanleitung

PowerWalker

PowerWalker VFI 1000T/E LCD Bedienungsanleitung

PowerWalker

PowerWalker VFI 6000 LCD Bedienungsanleitung

PowerWalker

PowerWalker VI 500 R1U Bedienungsanleitung

PowerWalker

PowerWalker VI THID Series Bedienungsanleitung

PowerWalker

PowerWalker VFI 10000 CG PF1 Bedienungsanleitung

PowerWalker

PowerWalker VI RLP Series Bedienungsanleitung

PowerWalker

PowerWalker VI SCL Series Bedienungsanleitung

Beliebte UPS Handbücher anderer Marken

Pylontech

Pylontech Victron & Pylontech US5000 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung

Mecer

Mecer ME-1000-WTU Bedienungsanleitung

Mustek

Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch

Emerson

Emerson Liebert NXL series Bedienungsanleitung

MAKELSAN

MAKELSAN BOXER SERIES Bedienungsanleitung

Block

Block PC-0524-400-0 Bedienungsanleitung

CyberPower

CyberPower CP585LCD Bedienungsanleitung

Eaton

Eaton 3S Montageanleitung

CyberPower

CyberPower Office Tower Series UPS 1000 Bedienungsanleitung

CyberPower

CyberPower BM100 Bedienungsanleitung

Best Power

Best Power 610 Bedienungsanleitung

Best Power

Best Power Unity/I UT3K Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Xantrex

Xantrex Trace 512 UR-UPS Bedienungsanleitung

Forza

Forza SL-1501UL Bedienungsanleitung

LEGRAND

LEGRAND keor 310081 Bedienungsanleitung

ABB

ABB Conceptpower DPA 500 Bedienungsanleitung