PowerWalker VI 400 Bedienungsanleitung

POWER WALKER VI 400/600/800

Uninterruptible Power Supply

USER’S MANUAL

PROBLEM POSSIBLE CAUSE SOLUTION

1. The power switch is in

“OFF” or not pressed

1. Press power switch to turn on.

2. The voltage for battery is

weak 2. Re-charge the UPS at least 8

hours.

3. Battery failure 3. Replace with the same type of

battery or call for service.

NO LIGHT (UPS

NOT ON)

4. Power Connection looses 4. Check the input power and

replug it again

BUZZER BEEPS

CONTINUOUSLY

1. Overload of the UPS. 1. Remove the noncritical load or

call for service.

1. Battery failure 1. Replace with same type of

battery or call for service.

2. AC fuse may be burnout. 2. Replace fuse or call for service.

3. Battery is not fully

charged.

3. Re-charge the UPS at least 8

hours.

BACKUP TIME IS

SHORT OR

ALWAYS IN

“BATTERY MODE”

4. Power Connection loses 4. Check the input power and

replug it again

7. TROUBLE SHOOTING

To call for service, please have the model, serial number, and

description of the problem available.

Thank you for

purchasing PowerWalker UPS.

Safety information and operating instructions are

included in this manual. To ensure the correct use of the

UPS, please read this manual thoroughly before operate

it. And save this manual properly.

1. INTRODUCTION

PowerWalker VI series is a line interactive UPS which is

designed to protect your personal computer or sensitive

electronic equipments. The UPS is equipped with boost

to stabilize input voltage. And it also employs

microprocessor control and allows wide input voltage

from 85VAC to 284VAC with overload protection. The

UPS can be automatically started up without AC power

supplied. In addition, this UPS provides advanced

modem or telephone line surge protection, and compact

design conserves space which can be placed in

horizontally or vertically on your desk. It is equipped with

many features that allow any attached equipment to

operate longer and more reliability. It is ideal protection

equipment against spikes, surges, sags or blackouts.

Description of Features:

.Compact size and light weight design which can placed

in horizontally or vertically on the cabinet or desk

.Easy to use and install

.Utilized microprocessor control to maximize the

reliability and efficiency

.Equipped with built-in boost function

.Cold start function

.Battery power energy saving and overload protection

.Provides advanced telephone/fax or modem surge

suppression protection

.Built-in RS-232 with connecting intelligent monitoring

software

Front Panel

2. SAFETY REQUIREMENTS

.Please save this manual properly. This manual

includes important safety information. Please read it

carefully and thoroughly before operating the UPS.

Comply with all the warnings and operating instructions

on the unit and in the manual strictly.

.To reduce the risk of electric shock, the user must

disconnect the UPS from the mains supply before

installing any cable.

.To reduce the risk of electric shock. Do not attempt to

disassemble the UPS. This UPS is no user serviceable

parts inside. Please contact qualified service personnel

to do any service.

.Do not connect with laser printers, cosmetic appliances,

medical equipments, microwave ovens, vacuum

cleaners or heavy duty hardware to UPS because they

take too much power.

.Do not dispose of batteries in a fire. They may explore.

.Do not open or mutilate batteries. They contain an

electrolyte that is toxic and harmful to the skin and

eyes.

.Do not allow liquid or foreign object to enter inside of

UPS.

.Do not block off ventilation openings in the UPS

system's housing.

.Do not place the UPS near water or in environments of

excessive humidity.

.Remove personal metal items such as rings, bracelets,

necklaces, and watches when working with batteries.

Batteries can produce a short-circuit current high

enough to make metal melt, and could cause severe

burns.

3. OVERVIEW

1. ON/OFF Button

Press the On/Off button to turn on or off

2. LED INDICATOR

- On-Line Indicator

The green light indicator illuminates when the input

line voltage is normal

- Backup Indicator

The green light indicator flashes when the internal

battery is being used

Back Panel

IEC

1. Battery Power Supplied Receptacle

The power supplied receptacles are used for battery to

power up your equipments while AC is failure.

2. AC Input Power Receptacle

The power receptacle is used to plug in the power cord

that provides power to the UPS

3. Circuit Breaker

The circuit breaker is used to protect your equipment

against the event of short-circuit or system overload.

4. Telephone/Fax/Modem Surge Suppression Port

This surge suppression port is used to protect the

telephone or modem line while connecting the

5. RS-232 Communication Port

This communication port is used to communicate with

a computer or modem and support the operating

systems

4. INSTALLATION

Before the installation, please ensure the power switch

on the UPS is in "OFF" position, and the voltage of the

AC utility source corresponds to the identification label

on the rear panel.

1. Inspection

Inspect the UPS upon the receipt. If there is any

damage, please report it to dealer immediately. The

packaging is used recyclable material, please save it

for reuse or dispose of it properly.

2. Placement

Install the UPS in a protected area within a

temperature range from 0 - 40oC and relative humidity

of 0 - 90% without condensing. And place the UPS in

a location free from excessive dust and chemical

fumes. Please notice that the UPS voltage and power

rating match to the line voltage and load requirements.

3. Connection

Connect the power cord to the utility power to power

up the UPS. Press "ON" button to turn on the UPS,

the green light indicator illuminates that AC utility

voltage is present.

4. Charge the Battery

Charge the battery automatically when UPS is

connected to utility power. Some charges may be lost.

It is recommended that the battery will be re-charged

for at least 8 hours before using the UPS.

5. Connect the Computer

Connect the interface cable from your computer to the

output receptacles on the back panel of the UPS.

6. Connect the Telephone/Modem Line

Connect a single telephone cable into the "IN"

telephone/modem surge suppression port on the back

of the UPS. Require another length of telephone cable

to connect into "OUT" telephone/modem port on the

back of UPS to the modem input socket.

7. Connect the RS-232 Port

Connect a RS-232 serial cable from RS-232 on the

back of the UPS to Computer Systems that will be auto

detected.

8. Green Mode Function

"Green mode" enables to save the power if none of the

load is connecting.

9. DC Start Function

When the power is not supplied from AC utility, DC

start function will be started up automatically.

10. Switch Off

Press "OFF" button to turn off the UPS after use or

test.

MODEL

PowerWalker

VI 400

PowerWalker

VI 600

PowerWalker

VI 800

CAPACITY VA/W 400VA/240W 600VA/360W 800VA/480W

Voltage 110/120VAC or 220/230/240VAC

Voltage Range 85-140VAC or 162-290VAC

INPUT

Frequency 45-65 Hz (Auto Sensing)

Voltage

(Batt. Mode)

110/120/220/230/240VAC +/-10%

Frequency (Batt. Mode)

50Hz or 60Hz +/-1 Hz

OUTPUT

Output Waveform

(line mode)Battery mode

Modified Sinewave Stepwave

Battery Type 12V4.5Ah x 1 12V7Ah x 1 12V9Ah x 1

Backup Time (at a PC

load with 15" monitor)

8 minutes 20 minutes 30 minutes

BATTERY

Recharge Time 8 hours to 90% after complete discharge

TRANSFER

TIME Typical : 4-6 ms and 13ms(max)

AC Mode Green lighting

INDICATOR Backup Mode Green flashing

Backup Mode Sounding every 10 seconds

Low Battery Sounding every second

AUDIBLE

ALARM

Overload Sounding every 0.5 second

PROTECTION Full Protection Discharge, overcharge, and overload protection

PHYSICAL

Dimension DxWxH(mm)

287x212x107

ENVIRONMENT Noise Level Less than 40dB

Smart RS-232

Windows family, Sun Solaris, IBM Aix, Compaq

True64, UnixWare, FreeBSD, HP-UX, Linux and

MAC

INTERFACE

5. MONITORING SOFTWARE

After the UPS has been installed, you must install the

software(Smart Power) that came packaged with your

UPS. Smart Power monitoring software performs the

monitoring and controlling functions. This software

displays the status and diagnostic symptoms on the

monitor. In case of the power failure, it provides the auto

shutdown for the computer.

If you download the software from Internet, please key

the serial number: 726T25-4791-2N39546.

6. TECHNICAL SPEICIFICATION

910

Inhaltsverzeichnis

Andere PowerWalker UPS Handbücher

PowerWalker

PowerWalker 6000C LCD Bedienungsanleitung

PowerWalker

PowerWalker VFI 1000R LCD Bedienungsanleitung

PowerWalker

PowerWalker PowerMust 6054 Bedienungsanleitung

PowerWalker

PowerWalker VFI 1000CRM LCD Bedienungsanleitung

PowerWalker

PowerWalker VFI 6000 CG PF1 Installations- und Betriebshandbuch

PowerWalker

PowerWalker VI 750 PSW Bedienungsanleitung

PowerWalker

PowerWalker VFD 600 APFC Bedienungsanleitung

PowerWalker

PowerWalker VFI 10000CP 3/3 Bedienungsanleitung

PowerWalker

PowerWalker VFI 10K-80K CPG 3 Bedienungsanleitung

PowerWalker

PowerWalker BP P96T Administratorhandbuch

PowerWalker

PowerWalker VFI 3000 LCD Installationsanleitung

PowerWalker

PowerWalker VFI 1000RM Bedienungsanleitung

PowerWalker

PowerWalker VFI 10000CP 3/3 Bedienungsanleitung

PowerWalker

PowerWalker 650 SH Bedienungsanleitung

PowerWalker

PowerWalker VFI 1000 Bedienungsanleitung

PowerWalker

PowerWalker VFI 2000 CRM Bedienungsanleitung

PowerWalker

PowerWalker VI 400 SC Bedienungsanleitung

PowerWalker

PowerWalker 1000 LCD/UK Bedienungsanleitung

PowerWalker

PowerWalker VFI ICT IoT Series Bedienungsanleitung

PowerWalker

PowerWalker VFI 1000 R1U Bedienungsanleitung

PowerWalker

PowerWalker VI 500T/HID Bedienungsanleitung

PowerWalker

PowerWalker VI THID Series Bedienungsanleitung

PowerWalker

PowerWalker VI 650SE LCD Bedienungsanleitung

PowerWalker

PowerWalker VI 1000 Bedienungsanleitung

Beliebte UPS Handbücher anderer Marken

Pylontech

Pylontech Victron & Pylontech US5000 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung

Mecer

Mecer ME-1000-WTU Bedienungsanleitung

Mustek

Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch

Emerson

Emerson Liebert NXL series Bedienungsanleitung

MAKELSAN

MAKELSAN BOXER SERIES Bedienungsanleitung

Block

Block PC-0524-400-0 Bedienungsanleitung

CyberPower

CyberPower CP585LCD Bedienungsanleitung

Eaton

Eaton 3S Montageanleitung

CyberPower

CyberPower Office Tower Series UPS 1000 Bedienungsanleitung

CyberPower

CyberPower BM100 Bedienungsanleitung

Best Power

Best Power 610 Bedienungsanleitung

Best Power

Best Power Unity/I UT3K Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Xantrex

Xantrex Trace 512 UR-UPS Bedienungsanleitung

Forza

Forza SL-1501UL Bedienungsanleitung

LEGRAND

LEGRAND keor 310081 Bedienungsanleitung

ABB

ABB Conceptpower DPA 500 Bedienungsanleitung