PR Lighting XPar 1012 Bedienungsanleitung

XPar1012

PR-8208

The user manual contains important information about the safe installation and use of a projector. Please read

and followtheseinstructions carefullyandkeep themanual in asafeplaceforfuture reference.

PR LIGHTING LTD.

http://www.pr-lighting.com

INDEX

1.SAFETYANDWARNINGS……………………………………………………………………………………………

2. INSTUCTIONS………………………………………………………………………………………………………

●CLEANINGANDMAINTENANCE………………………………………………………………………………

●TROUBLESHOOTING………………………………………………………………………………………………

3.APPEARANCE………………………………………………………………………………………………………

4.INSTALLATION……………………………………………………………………………………………………

●RIGGING……………………………………………………………………………………………………………

●PLACEAUNITONAFLATSURFACE……………………………………………………………………………

●INSTALLATIONOFTHEACCESSORIES………………………………………………………………………

●TRANSPORTATION…………………………………………………………………………………………………

●POWERCONNECTIONS…………………………………………………………………………………………

●DMXCONTROLCONNECTION…………………………………………………………………………………

●DMXTERMINATOR………………………………………………………………………………………………

5.SETUPANDCONFIGURATION……………………………………………………………………………………

●FRONTPANELOPERATION………………………………………………………………………………………

●DMXSTARTADDRESS……………………………………………………………………………………………

●STAND-ALONEMODE……………………………………………………………………………………………

●MASTER/SLAVEMODE……………………………………………………………………………………………

6.OPERATIONMENU…………………………………………………………………………………………………

7.DMXPROTOCOL…………………………………………………………………………………………………

8.TECHNICALDATA…………………………………………………………………………………………………

●SIZES………………………………………………………………………………………………………………

●LIGHTOUTPUT…………………………………………………………………………………………………

9.CIRCUITDIAGRAMANDPCBCONNECTIONS…………………………………………………………………

●CIRCUITDIAGRAM………………………………………………………………………………………………

●PCB CONNECTIONS………………………………………………………………………………………………

10.COMPONENTORDERCODES……………………………………………………………………………………

ACCESSORIES

The following itemsaresuppliedwith theprojector and please check:

Name

Quantity

Unit

Remark

Gclamps

Powercord

XLR Cable

Pcs

XLRconnector

Set

Male and female

Safetycord

User manual

TransparentCover+seal+screws×6

Set

Optional

BarnDoor+ Frostpanel(Optional)

Set

Optional

Shading barrel

Set

Optional

Please note that as part of our ongoing commitment to continuous product development, specifications are

subject to change without notice. Whilst every care is taken in the preparation of the manual we reserve the

right to change specifications in the course of product improvement. The publishers cannot be held responsible

for the accuracy of the information herein, or any consequence arising from them.

Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and /

or the units are in good condition before installation and use. Should there be any damage caused by

transportation, consult your dealer and do not use the unit. Any damage caused by improper use will not be

assumed by the manufacturer and / or dealer.

1. SAFETYANDWARNINGS

NOTE

Before a projector’s installation, power-on,operationandmaintenance,pleasecarefullyread

thesafetyinformationhereinafter!

Thefollowing safetysignsareusedintheusermanual.

Warning

User

Manual

Electrical

shock

Goggles

Protective

Gloves

Flames

High

Temperature

● When unpacking , check if there is transportation damage before using the projector. Should there be

anydamagecausedbytransportation,consultyourdealeranddonotuseit.

●The manufacture is not responsible for loss caused by the user not following the manual or changing the

projectorashe/shelikes

●Please be noted that the damage caused by changing the projector at willisnotwarranted.

●Do not hesitate to contactthedealer or the manufacturer ifanyquestionsor advice.

●The unit with lower protection level is only used indoors, for those with IP65, they can be used both indoors and

outdoors.

● Useonlyindrylocations.Keepthis unitawayfromrainand moisture, excessive heat,humidityanddust. Do not

allowcontactwithwaterorany otherliquids.

●It’s forbidden to make the unit withlower protectionleveldirectlyor indirectlycontact waterorother liquids.

●The projector should be kept away from high temperature, fire, electrical surge, vibration and strong light while

being operated

●The projector is only intended for installation, operation and maintenance by qualified personnel. And the

operationmuststrictlyfollowthe proceduresinthe manual

●No repairable parts in theprojector anddonotopencoversfor maintenancebyyourself.

●Don’t look straightly into thelightsourcesespeciallyfor epileptics, otherwise eyeswillbe burned.

●Do not connect this device to any typeofdimmer pack

●After lamp switched on, the minimumdistancebetween theprojector andilluminated surfaceis10m

●lens and other optical parts shall be replaced immediately if they have deformed or been damaged, otherwise the

lightoutput willbe compromised.

●Before operation, please confirm that all covers(housing) are on and screws tightened. It’s forbidden to use a

projectorwhilecovers(housing)areoff

●Keep the lamp clean and do not touch it with bare hands.

●While operating it, wear protective items.

●Any electrical connection must be carried out by a qualified person .

●Before installation, please confirm the voltage supplied matcheswhatisrequired for theprojector

●Each projector must be properlyearthedandinstalledasper related electricalstandards.

●Do not use power cord with its insulator damaged and connect the power cord with other cables.

●If the projector is not used or under cleaning,, please hold the plug and unplug it. Do not unplug it forcefully or

bypullingthepower cable.

●All power cords must conform to related safety and regulations

●While beingoperated,theprojectorshouldnotbeunderrainsorinhumidity.

●Do not switch on and off the projector constantly in very short intervals, otherwise the light source’s and other

electricalparts’ life willbe shortened.

●There are safety cord holes at the bottom of the base of a projector. In view of safety, please run the safety

cord supplied throughthesafetycord holesfor safetysupport.

●Before any installation, maintenance and cleaning work, please ensure the projector is disconnected from

powermains.

●Under normal temperature, after being stable, the unit’s surface (the surface of the heat sink)temperature

willbe 55℃

●Whilethe lamp is stricken for the first time, there will be smoke and strange smell. It’s normal and does not

mean the projector has some defects.

●While operated, do not touch the metallic housing. It is very hot during operation.

●Do not mount the projector directly on inflammable surface.

●Do not project the beam straightly on combustible items and the minimum distance between the projector

and illuminated itemsis10m.

●A projector should be installed with good ventilation and the minimum distance between the projector and

wallsis 50cm.Atthe same time,pleaseensure thefansandairinletsandoutlets areworkable.

2. INSTRUCTIONS

●CLEANINGANDMAINTENANCE

Before the normal useof the unit, its protectingdevice needsto be periodicallychecked . For example, check if the fuse isblown up.

Ifyes,replaceit witha fusewithsame ratings. Please be noted that it mustbeafuse withexactlysame ratings.

The unithas over-temperature protection device(if over-temperature, the device will shut off the power supply). Please periodically

check coolingsystem.Thecooling systemincludescooling fans, heatsinkandother coolingcomponents;pleasecheckifthefans

run normally. Check if the fans and air vents are free of blockage, making sure air vents are not blocked. The fans need to be

cleaned every15dayperiodically.

For the units with optical lens, reflector and hot mirror, because of the accumulation of the smoke, oil and dust on the lens, the

light outputwill be compromised. For the reliable use of the unit, it is very necessary to keepit clean. Internaland externaloptical

lens, glass panels,reflectorsand hot mirrorsneed tobecleanedperiodicallyfortheoptimized lightoutput.

The unit haswater-proof function at some level. Unless it isconfirmed by a qualified person for the replacement of some internal

components, dismantlement of itis forbidden. For the unit of this type, if without any cooling fan, just keep it clean. If with fans,

pleasereferdescriptionsaboveforcleaning.

Cleaning frequency is to bedecided by operations and its environment. Use soft clothand normal detergent for glassfor cleaning

work. It’s advisedexternal optical systembe cleanedevery20days and internal opticalsystems every30/60days. Keep lens clean

and do not touchoptical parts with bare hands.

●Beforeanymaintenanceandcleaning,pleaseensuretheprojectisoffthepower

●Onlyqualifiedpersonisallowedto do maintenance

●Duringmaintenance andbeforemaintenance,the projector mustbe off power.

●To avoid internal damage, sun light or other light mustn’t penetrate into the projector via front lens whether

itrunsor not

●Do not use alcohol or other organic solvent to clean the housing to avoid damage.

●Do not use any solvent with chemical elements to clean color filters or hot mirror.

●TROUBLESHOOTING

PROBLEM

ACTION

The projector doesn’t switch on

Checkthe power cordconnection.

Power Switch fails or is not connected well, call a professional

technicianforrepairingand checking.

Control board is not connected normally, call a professional technician

forrepairingandchecking.

The projectcanbeturned on,but theLED lamps

can’t be on

LED lamp board is notconnected well, call a professional technician for

repairingand checking.

The LEDlamps canbe on,butnotcontrolled

byDMX

CheckDMXStartAddress.

CheckifXLRcablefailsornot.

Thebrightnessdecreasesobviously

Ambient temperature is too hot which makes the projector too hot,

pleasetakeappropriateventilationmeasures.

3. APPEARANCE

Product’s External Functional Sketch：

NO.

Name

Remarks

Frostpanel（Optional）

Othercomponents shouldbeselected if frostpanelselected

BarnDoor （Optional）

Knob

Support

Arm

XLRcable

Small

PowerCord

Big

TransparentDisplayCover（Optional ）

Usedinharshenvironmentlikedustyareaorbeingunderwater

4. INSTALLATION

吊臂

保险绳

穿过保险绳孔

Arm

Safetycord

Runthesafetycordthroughthehole

●RIGGING

Take 1 clamps and the safety cord out from the package and mount 2 clamps on the underside of fixture with 2 retainers attached to

each clamp. Hang the fixture on the structure and fasten the screws attached to each clamp. (See the WARNINGonthe underside of

the base as shown above) To pass the SAFETYCORDthrough the HOLES for safety! Always ensure that the projector is firmly

anchored to avoid vibrationand slipping whilst functioning. Always ensure that thestructurethat youare going to mount theprojector

to is secure and strong enough to support the weight of the unit Loosen the bigger knob and adjust the head’s angle for the effect

desiredandthetightenit.Theinstallationis completed.

●PLACEAUNITONAFLATSURFACE

Before placing a unit on a flat surface, loosen the small knob with the support and make the angle between the arm and the support

60degrees.Tightenthesmallknob.Loosenhebig knoband adjusttheangle betweenthearmand unitasdesired andthentightenit.

●INSTALLATIONOFTHEACCESSORIES

If barn doorselected,its installationisillustrated in thediagrambelow:

Loosen the screw in the shape of a butterfly(1) in the front part of the unit(4), turn the clipping componentin the shapeof

7by alittleamount,then placethebarn door(3).Turn the clipping componentbackward and tighten the butterflyscrews.

Runone end of the safety cord through safety cord hole on theunit’s bodyand theotherend of it throughthe safetycord

holeonthebarddoorto finishtheinstallationofthebarndoor.Turn thebarn door, andopenorclosethebarndoorblades

toreachtheeffectdesired.

1 2 43

Safetycordhole

If theTopHatis selected, Its Installation is illustrated inthediagramsbelow:

Loosenthe screwin the shape ofabutterfly(1)inthefrontpartoftheunit(4), turntheclipping component(2)intheshape

of 7byalittleamount, thenplace theTopHat(3).Turn the clipping component(2)backwardandtightenthebutterfly

screws(1).Runoneendofthesafetycord through safetycord holeontheunit’sbodyand theotherendof itthroughthe

safetycordhole ontheTopHattofinishthe installationoftheTopHat.

If thefrostpanelisalsoselected,it mustbeusedincombinationof thebarndoor.ItsInstallationandDismantisillustrated

inthediagrams below:

●TRANSPORTATION

Beforetransportation, tighten both knobs afterthe armand supportare overlapped.

WARNING:

●TheprojectorMUSTbe liftedorcarried by the HANDLESinsteadofclamps.

●.For safety the safety cord should afford 10 times the Projector’s weight.

●POWERCONNECTION

Connect thepowercordasfollows:

L(live)=brown

E(earth)=yellow/green

N(neutral)=blue

Before power connection, please ensure the power supplied mustmatch what the nameplate says. It is recommended that each

projectorbe connected withpower separatelyso that theymaybeindividuallyswitched onand off.

Note: If projectors are connected in series, please connect POWERIN port of the 1st projector with the Power Mains, then

connectitsPOWEROUTwithPOWER INof the2nd projector,and soontillallfixturesareconnected.Ifthevoltage supplied

is 200V-240V, the maximum projectors connected is 8pcs, if it is 100V-120V, the maximum is 4pcs. The diameter ofthe cores

ofthewiresforthePower in/outcablesmustbeequalorbigger than2.5mm2.

●Theearth wire(yellow/green)must be connectedtotheground. Andelectrical connection mustbein

accordancewiththe standardsconcerned.

●If anyquestionsabout the electricalinstallation, donotcontinue butconsult aqualifiedelectrician.

螺母×4

柔光板

遮光板组件

Barndoor

Frost Panel

Screwx 4

●DMX CONTROLCONNECTION:

Connection between controller and projector and between one projector and another must be made with a twin-screened cable, with

each wire having at least a 0.5mm in diameter. Connection to and fromthe projector is via cannon 5 pin (which are included with the

projector)or5pinXLRplugsand sockets.The XLR'sareconnected asshowninthe figureabove.

Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. XLR plugs and sockets

mustn’t be connected in any way other than mentioned in the above figure. The unit accepts digital control signals in protocol

DMX512(1990).

Connect the controller’s DMX output to the first fixture’s DMX input, and connect the first fixture’s DMX output to the second

fixture’s DMX input and connect the rest fixtures in the same way. Eventually connect the last fixture’s DMX output to a DMX

terminatorasshowninthe figurebelow.

●DMXTERMINATOR

In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This prevents

electrical noisefromdisturbingandcorruptingtheDMXcontrolsignals.

The DMX terminator is simply an XLR connector with a 120(ohm) resistor connected across pins 2 and 3, whichis then plugged

into theoutput socketonthelast projector inthe chain.The connectionsareillustrated below.

接电源

接控制器

接回路插

POWER IN POWER OUTPOWER OUT

POWER IN

DMX OUT

DMX IN

120

DMX TERMINATOR

CONNECTION

Connect a 120 (OHM) resistor

across pins 2 and 3 in an XLR plug

and insert into the DMX out socket

on the last unit in the chain. PIN 3

PIN 2

DMX

terminator

DMX Controller

Power

5. SETUPANDCONFIGURATION

●FRONTPANELOPERATION

Projectorconfigurationcanbe setconveniently viapushbuttonandLCDdisplay.

Launch the projector and press button ENTER for more than 3 secondsto unlock the panel, the LCD will show the function menu of

the projector, each main menu has its submenus and each submenu has a specific function. For details, please see the

“OPERATION MENU” section.

Pressbutton UP or DOWN ifyouwanttobrowsethroughthevariousSetup Options.

Pressbutton ENTER to save your settingsorenterthesubmenu.

Pressbutton UP or DOWN tochangevalues(plusorminus)

Pressbutton FUNC, it willreturnto the upper menu.Ifbutton FUNC notpressed, the defaultwillshowdisplaystatusautomatically.

●DMX STARTADDRESS

Each Projector mustbegivena DMXstartaddressso that the correctprojectorrespondsto thecorrectcontrol signals. ThisDMXstart

address is the channel number from which the projector starts to “listen” to the digital control information being sent out from the

controller. The Unit has 2 DMX modes. Thereare standard mode and extended mode. For example standard mode has6 channels,

so set the No. 1 projector’s address 001, No. 2 projector’s address 007, No. 3 projector’s address 013, No. 4 projector’s address019,

and soon.

Launchtheprojector. Pressbutton ENTER more than2secondsto unlock panel.

Pressbutton ENTER todisplayDMXaddress;

Pressbutton UP and DOWN, youcanset the address;

Pressbutton ENTER to confirm; after poweredonnext time,the defaultwillbe last value saved

Pressbutton FUNC,itwillreturnto theuppermenu

●STAND-ALONEMODE

Operate the projector without connecting with a controller, enable the master mode through the operation panel, the

projector will run in Stand-Alone mode automatically.

DMX address can be set at any number within 512.

●MASTER/SLAVEMODE

Many projectors can run synchronously in the Master/Slave mode by linking them with each other. First,

connect the first fixture’s DMX output to the second fixture’s DMX input using XLR-XLR control cable and then connect the second

fixture’s DMX output to the third fixture’s DMX input, and so on until all projector are connected in this way. Eventually connect the

last fixture’s DMX output to a DMX terminator. Set 1st projector as the master and others are Slaves.

StartAddressesofallSlavesare001; Operationmodeof the Master can be set any mode for a Master’ and Slaves’ operation mode can

besetaccordingly.

AfterPowered on,the group willruninMaster/SlaveMode

Inhaltsverzeichnis

Andere PR Lighting DJ-Equipment Handbücher

PR Lighting

PR Lighting XS 250 Bedienungsanleitung

PR Lighting

PR Lighting PR-6000 Spot Bedienungsanleitung

PR Lighting

PR Lighting XRLED 1200 SPOT Bedienungsanleitung

PR Lighting

PR Lighting Junior JNR Minifresnel 100MZ-W Bedienungsanleitung

PR Lighting

PR Lighting XLED 1037 Bedienungsanleitung

PR Lighting

PR Lighting AQUA 350 BEAM PR-2368 Bedienungsanleitung

PR Lighting

PR Lighting LED Studio 3200T Bedienungsanleitung

PR Lighting

PR Lighting MEGA COLOUR 2000 Bedienungsanleitung

PR Lighting

PR Lighting PR-3203T Bedienungsanleitung

PR Lighting

PR Lighting XLED 6019 Bedienungsanleitung

PR Lighting

PR Lighting JNR-8119A Bedienungsanleitung

PR Lighting

PR Lighting JNR PAR COB Bedienungsanleitung

PR Lighting

PR Lighting PR-8541 Bedienungsanleitung

PR Lighting

PR Lighting Pro Stage 150 RGBW 19 Bedienungsanleitung

PR Lighting

PR Lighting XL 1200 Bedienungsanleitung

PR Lighting

PR Lighting PR-8102 Bedienungsanleitung

PR Lighting

PR Lighting XR480 BEAM Bedienungsanleitung

PR Lighting

PR Lighting XR480S BWS Bedienungsanleitung

PR Lighting

PR Lighting AQUA LED 1800 FRAMING Bedienungsanleitung

PR Lighting

PR Lighting XPar 390 Bedienungsanleitung

PR Lighting

PR Lighting XLED 300 Beam Bedienungsanleitung

PR Lighting

PR Lighting PR-8802 Bedienungsanleitung

PR Lighting

PR Lighting XPar 336-W Bedienungsanleitung

PR Lighting

PR Lighting StarBrite Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Zumtobel

Zumtobel APHRODITE Home Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung