Premier Mounts AM175 Bedienungsanleitung

INSTALLATION INSTRUCTIONS

AM175

Universal Low Prole Swingout Arm for 37” to 63” Flat Panels

NORTH AMERICA

3130 East Miraloma Avenue

Anaheim, CA 92806 USA

USA and Canada –

Phone: 800-368-9700

Fax: 800-832-4888

EUROPE

Swallow House,

Shilton Industrial Estate,

Shilton, Coventry, England CV79JY

Phone: +44 (0) 2476 614700

Fax: +44 (0) 2476 614710

Other Locations – Phone: (001)-714-632-7100; Fax: (001)-714-632-1044

©Premier Mounts 2010

9531-008-001-0A

CREATING POSITIVE CUSTOMER EXPERIENCES

Page 2 Installation Instructions

Table of Contents

Warning Statements

Warning Statements 2

Parts List 3

Installation Tools 3

Wood Stud Installation 5

Concrete Surface Installation 7

Determining the Mounting Hardware 8

Universal Spacer Installation 9

Griplate™ Installation 9

Mounting Bracket Installation 10

Adapter Plate Installation (optional) 11

Attaching the Flat Panel to the Wall 12

Securing and Leveling the Flat Panel 12

Adjusting the Flat Panel Tilt 13

Plastic Channel Cover Installation 13

Technical Specications 14

Warranty 15

AM175

PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION INSTRUCTIONS SHOULD BE READ AND

COMPLETELY UNDERSTOOD. THE INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL INJURY AND

PROPERTY DAMAGE. KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE

REFERENCE.

PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS

PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED

ATTACHMENTS OR MODIFICATIONS, AND IS NOT RESPONSIBLE FOR ANY DAMAGES, CLAIMS, DEMANDS, SUITS,

ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM, ARISING OUT OF OR IN ANY MANNER

RELATING TO ANY SUCH USE, ATTACHMENTS OR MODIFICATIONS.

THE SURFACE MUST BE CAPABLE OF SUPPORTING AT LEAST FIVE TIMES THE WEIGHT OF THE FLAT PANEL. IF NOT, THE

STRUCTURE MUST BE REINFORCED. THE MAXIMUM WEIGHT THAT CAN BE USED WITH THIS PRODUCT IS 175LBS. PROPER

INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN, AS OUTLINED IN THE INSTALLATION INSTRUCTIONS,

MUST BE ADHERED TO. FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY, OR EVEN DEATH.

SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE ASSEMBLY OF THIS PRODUCT. USE PROPER SAFETY

GEAR AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY.

At least two qualied people should perform the assembly procedure. Injury and/or damage can result from dropping or mishandling the at

panel.

If mounting to studs, make sure that the mounting screws are anchored into the center of the studs. Use of an edge-to-edge stud nder is

recommended.

Be aware of the mounting environment. If drilling and/or cutting into the mounting surface, always make sure that there are no electrical

wires in wall. Cutting/drilling into an electrical line may cause serious injury.

Make sure there are no water lines inside the wall where the mount is to be located. Cutting/drilling into a water line may cause severe water

damage to the mounting surface.

This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal injury.

Do not install near sources of high heat. Do not install on a structure that is prone to vibration, movement or chance of impact

Contact Premier Mounts with any questions

(800) 368-9700

[email protected]

Installation Instructions Page 3

Parts List

AM175

Make sure your Premier Mounts product has the following hardware and components before begin-

ning installation. If there are parts missing and/or damaged, stop the installation and call Premier

Mounts at (800) 368-9700.

Installation Tools (not supplied)

Phillips Screwdriver 1/4” Drill Bit Electronic Stud Finder Drill Level

1/2” Socket and Socket

Wrench

Tape Measure

Universal

Spacers (Qty 24 )

Thread Depth

Indicator (Qty 1)

Swingout Arm (Qty 1)

5/16” x 3” Lag Bolts (Qty 6) 5/16” Flat Washers (Qty 6) Griplate™ (Qty 6)

Universal Mounting Brackets (Qty 2)

Extension Adapter Hardware Pack

5/16” Flat Washers

(Qty 4)

M8 Nylon Nut

(Qty 4)

Extension Adapters (Qty 4)

Channel Covers (Qty 6)

Page 4 Installation Instructions

AM175

M4 x 16mm (Qty 6)

M4 x 25mm (Qty 6)

M4 x 30mm (Qty 6)

M6 x 30mm (Qty 6)

M6 x 25mm (Qty 6)

M6 x 16mm (Qty 6)

M5 x 30mm (Qty 6)

M5 x 25mm (Qty 6)

M5 x 16mm (Qty 6)

M8 x 30mm (Qty 6)

M8 x 25mm (Qty 6)

M8 x 16mm (Qty 6)

If your unit requires alternative mounting hardware, use commercially available hardware or contact Premier Mounts (800) 368-9700.

M6 x 45mm (Qty 6)

M8 x 45mm (Qty 6)

M8 x 70mm (Qty 4)

Installation Instructions Page 5

AM175

Wood Stud Installation

THE FOLLOWING STEPS MUST BE PERFORMED BY TWO PEOPLE.

Wall Stud

Electronic

Stud Finder

Step 1. Determine the desired viewing location. Use a

stud nder to locate two studs closest to the

viewing location.

Step 2. Once the studs have been located, use a pencil

to mark the center of each stud.

Step 3. Drill a pilot hole at the marked location using a

power drill and a 1/4” drill bit.

1/4” Drill

Bit

Wall Stud

Two people must perform the installation. One

person must hold the mount while the other person

levels the mount. The mount must remain in place

while the mounting hardware is tightened.

Only use 1/4” drill bit when drilling the

pilot holes.

A minimum of two (2) wall studs must be

used in the installation of this product.

Upper Mounting

Channel

Mounting Slot

Flat Washer

5/16” Lag Bolt

1/2” Socket

Wrench

Step 4. Level the mount.

Step 5. Align the mounting slot with the drilled hole.

Step 6. Insert and tighten one (1) 5/16” x 3” lag bolt and

at washer. Tighten using a 1/2” socket

wrench. Do not completely tighten the lag bolt

at this time.

Do NOT over-tighten lag bolts when

attaching the mount to the wall. Improper

installation may result in personal injury or

damage to property.

When determining viewing height, the center

of the TV should be at eye level while sitting in

an upright position. When using the flat panel

as room decoration, raise it to the point where

the bottom of the screen is at eye level while

sitting and the top is eye level when standing.

Page 6 Installation Instructions

AM175

Do NOT over-tighten lag bolts when

attaching the mount to the wall. Improper

installation may result in personal injury or

damage to property.

Step 10. Re-level the AM175.

Step 11. Using a 1/2” socket wrench, completely

tighten the two (2) upper lag bolts.

If the studs are 12” (304.8mm) apart, use three 3” (76.2mm) lag bolts for the upper mounting channel and three 3” (76.2mm)

lag bolts for the lower mounting channel. If the studs are 16”(406.4mm), 18” (457.2mm) or 24”(609.6mm) apart, use two 3”

lag bolts for the upper mounting channel and two 3” lag bolts for the lower mounting channel.

There will be a total of four (4) mounting

points (2 for the upper mounting channel and

2 for the lower mounting channel).

Upper Mounting Channel

Mounting Slot

Flat Washer

5/16” Lag Bolt

1/2” Socket

Wrench

Before drilling the second mounting hole,

re-level the mount.

Step 7. Drill a pilot hole at the marked location using a

power drill and a 1/4” drill bit.

Step 8. Align the mounting slot with the drilled hole.

Step 9. Insert and tighten one (1) 5/16” x 3” lag bolt and

at washer. Tighten using a 1/2” socket

wrench. Do not completely tighten the lag bolt

at this time.

Repeat these steps to secure the lower mounting channel

to the wall.

A minimum of two (2) wall studs must be

used in the installation of this product.

Installation Instructions Page 7

AM175

Concrete Surface Installation

If concrete wedge anchors are not used (as described in these installation instructions) and you decide on other mounting

hardware, please follow the installation instructions as provided with that hardware.

THE FOLLOWING STEPS MUST BE PERFORMED BY TWO PEOPLE.

Level

Mark

Step 1. Determine the desired viewing location.

Step 2. Place the mount into position against the

wall and level the mount.

Step 3. Mark off four holes to be used for securing the

mount.

Step 4. Next, drill holes using a masonry bit (commercially

available) for your anchors.

Step 5. Insert a commercially available concrete anchor into

each hole.

Step 6. Use a hammer and lightly tap each anchor into place

so that only the threaded shaft of the concrete wedge

anchor is protruding from the wall.

Concrete Wedge Anchor

Drill HammerThreaded Shaft

When determining viewing height, the center

of the TV should be at eye level while sitting in

an upright position. When using the flat panel

as room decoration, raise it to the point where

the bottom of the screen is at eye level while

sitting and the top is eye level when standing.

Page 8

AM175

Determining the Mounting Hardware

Step 7. Once all of the anchors are in place, move

the wall bracket into position.

Step 8. Attach the nut onto the threaded shaft that

is protruding from the wall.

Step 9. Re-level the wall plate and tighten all

concrete wedge anchor nuts at this time.

If concrete wedge anchors are not used (as described in these installation instructions) and you decide on other mounting

hardware, please follow the installation instructions as provided with that hardware.

1/2” Socket

Threaded

Shaft

Nut

Level

Do NOT over-tighten the concrete wedge anchors.

Small Straw or Toothpick

Small Straw

or Toothpick

Small Straw

or Toothpick

Marking the 1/8”

Allowance

Depth Plus 1/8” Allowance

Mark

Depth Plus 1/8” Allowance

Mark

 Insert a small straw or toothpick into the threaded

inserts found on the back of the at panel.

® Use a pencil to mark the depth of the threaded

insert on the small straw or toothpick.

¯ Mark the straw or toothpick 1/8” above the depth of

the threaded insert, as shown in Figure 1.

° Insert the small straw or toothpick into the remaining

threaded inserts to compare and verify their depth

using the straw or toothpick’s 1/8” allowance mark.

± Locate the correct diameter screw for the threaded

insert.

If the screw you selected is longer than the 1/8”

allowance mark on the small straw or toothpick,

as shown in Figure 2 and Figure 3, do not use

this screw. The screw length must not bypass the

mark.

² Test each size of the screws provided.

The correct screws should thread easily into the

mounting point and not pull out when tension is

applied.

You must account for the bracket, spacers and

Griplate™ depths when using the Thread Depth

Indicator to measure the thread depth of your at

panel.

Installation Instructions Page 9

AM175

Universal Spacers Installation (optional)

The universal spacer may be stacked six (6) high, for a total stacking height of 1-1/2”. The universal spacers must be stacked in the

direction shown above. The universal spacers must be placed between the mounting bracket and the at panel.

The universal spacer will t M4, M5, M6 and M8 screws sizes.

If your at panel has uneven mounting points, or recessed

mounting points, please use the provided universal spacers.

The Griplates™ have M4, M5, M6 and M8 hole patterns to

t the hardware that your at panel requires.

EXAMPLE: If your at panel uses M8 screws,

use the M8 mounting points.

Griplate™ Installation

DIMPLES

FACING UP

DIMPLES

FACING DOWN

DIMPLES

FACING UP

DIMPLES

FACING DOWN

Pre-install the mounting screws, universal

spacers and Griplates™. Once mounted, push

down to eliminate movement from the bracket,

then tighten the rest of the hardware. Repeat

this process for the installation of the remaining

mounting bracket.

Dimples

Page 10 Installation Instructions

AM175

This kit provides a variety of screws with different lengths and diameters to accommodate most at panels.

Mounting Bracket Installation

The number and location of mounting points will vary between manufacturers.

Do NOT over-tighten the screws.

Step 1. Place your at panel screen down on a soft, at surface and locate the threaded mounting points that are located on the back

of the at panel.

Step 2. Determine which screw is the correct length (please see “Determining the Mounting Hardware” section).

Step 3. Attach each bracket to the at panel by aligning the holes on each bracket with the threaded inserts on the back of your

at panel, insert the screws through both and turn clockwise until they are fully inserted.

Mounting Hardware

Griplate™

Universal Spacer

Mounting Bracket

Mounting Point

Flat Panel

Andere Handbücher für AM175

Inhaltsverzeichnis

Andere Premier Mounts Rack & Stand Handbücher

Premier Mounts

Premier Mounts PDS-PLUS Bedienungsanleitung

Premier Mounts

Premier Mounts PBC-1.5 Series Bedienungsanleitung

Premier Mounts

Premier Mounts PRC-LA Bedienungsanleitung

Premier Mounts

Premier Mounts PP-5 Bedienungsanleitung

Premier Mounts

Premier Mounts ECM-3763D Bedienungsanleitung

Premier Mounts

Premier Mounts AM50 Bedienungsanleitung

Premier Mounts

Premier Mounts PCM-MS2 Bedienungsanleitung

Premier Mounts

Premier Mounts Multi-Monitor with table adapter MMT Bedienungsanleitung

Premier Mounts

Premier Mounts PDS-PLUS Bedienungsanleitung

Premier Mounts

Premier Mounts PFM-32C1 Bedienungsanleitung

Premier Mounts

Premier Mounts INW-UNIFM Bedienungsanleitung

Premier Mounts

Premier Mounts CTM-MS2 Bedienungsanleitung

Premier Mounts

Premier Mounts PSD-TTS/B Bedienungsanleitung

Premier Mounts

Premier Mounts AM95 Bedienungsanleitung

Premier Mounts

Premier Mounts PTDM2 Bedienungsanleitung

Premier Mounts

Premier Mounts PRC Bedienungsanleitung

Premier Mounts

Premier Mounts Elliptical Floor Cart and Stand PSD-EB72C Bedienungsanleitung

Premier Mounts

Premier Mounts GB-AVSTOR4 Bedienungsanleitung

Premier Mounts

Premier Mounts AM100 Bedienungsanleitung

Premier Mounts

Premier Mounts Universal Projector Mount PBL-UMS Bedienungsanleitung

Premier Mounts

Premier Mounts Universal Flat-Only Mount UFM Bedienungsanleitung

Premier Mounts

Premier Mounts Nesting Cart Series Bedienungsanleitung

Premier Mounts

Premier Mounts PP-FCTA Bedienungsanleitung

Premier Mounts

Premier Mounts PSD-TL Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung