Premier Mounts UNI Bedienungsanleitung
Universal Short Throw Projector Wall Mount
Model: UNI/UNIE
9533-019-011-01
INSTALLATION INSTRUCTIONS
NORTH AMERICA
3130 East Miraloma Avenue
Anaheim, CA 92806 USA
USA and Canada
Phone: 1-800-368-9700
Fax: 1-800-832-4888
Other Locations
Phone: (001) 714-632-7100
Fax: (001) 714-632-1044
EUROPE
Swallow House,
Shilton Industrial Estate,
Shilton, Coventry, England CV79JY
Phone: +44 (0) 2476 614700
Fax: +44 (0) 2476 614710
Page 2 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions
Table of Contents
PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS PRODUCT FOR
PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS OR
MODIFICATIONS, AND IS NOT RESPONSIBLE FOR ANY DAMAGES, CLAIMS, DEMANDS, SUITS, ACTIONS OR CAUSES OF ACTION
OF WHATEVER KIND RESULTING FROM, ARISING OUT OF OR IN ANY MANNER RELATING TO ANY SUCH USE, ATTACHMENTS OR
MODIFICATIONS.
SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE ASSEMBLY OF THIS PRODUCT. USE PROPER
SAFETY GEAR AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY.
At least two qualied people should perform the assembly procedure. Injury and/or damage can result from dropping or mishandling the
projector.
If mounting to studs, make sure that the mounting screws are anchored into the center of the studs. Use of an edge-to-edge stud nder is
recommended.
Be aware of the mounting environment. If drilling and/or cutting into the mounting surface, always make sure that there are no electrical wires in
wall. Cutting/drilling into an electrical line may cause serious injury.
This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal injury.
Do not install near sources of high heat. Do not install on a structure that is prone to vibration, movement or chance of impact
Contact Premier Mounts with any questions
(800) 368-9700
PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION INSTRUCTIONS SHOULD BE READ AND COMPLETELY UN-
DERSTOOD. THE INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL INJURY AND PROPERTY DAMAGE. KEEP
THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE.
Make sure there are no water lines inside the wall where the mount is to be located. Cutting/drilling into a water line may cause severe water
damage to the mounting surface.
UNI/UNIE
Weight Capacity
Maximum projector weight: 50 lb. THE WALL STRUCTURE MUST BE CAPABLE OF HOLDING FIVE
(5) TIMES THE WEIGHT OF THE PROJECTOR. IF NOT, THEN THE
WALL STRUCTURE MUST BE REINFORCED.
Warning Statements
Weight Capacity 2
Warning Statements 2
Installation Tools 3
Parts List 3
Features 4
Determining the Installation Height 5
Wood Stud Installation 6
Attaching the Projector Arm 7
Throw Distance Calculation 8
Attaching the Projector Mount 9
Extension Arm Installation (Optional) 12
Adjustable Mounting Bracket Installation 13
Utilizing the Storage Feature 14
Cable Management 15
Technical Specifications 16
Warranty 17
Disclaimer 17
Installation Instructions Visit the Premier Mounts website at http://www.mounts.com Page 3
Wall Plate
(Qty 1)
Arm Assembly
(Qty 1)
Adjustable Mounting Assembly
- Pre-Assembled (Qty 1)
End Cover
(Qty 1)
M5 x 8mm Security
Screws (Qty 7)
Internal Slide Plate
(Qty 1)
Phillips Screwdriver ¼˝ Drill Bit Electronic Stud Finder
Drill
Level
½˝ Socket and Socket
Wrench
Extension Arm - Optional (Qty 1)
included with the UNIE
Back Plate Covers
(Qty 2)
UNI/UNIE
M5 Allen Wrench
(Qty 1)
Extension Hardware Pack
M6 x 12mm Security
Screws (pre-assembled)
(Qty 2)
M6 x 16mm Security
Screws (Qty 2)
M6 Flat Washer
(Qty 2)
External Slide Plate
(Qty 1)
Parts List
Installation Tools
The following tools may be required depending upon your particular installation. They are not included.
Make sure your Premier Mounts product has the following hardware and components before beginning installation. If
there are parts missing and/or damaged, stop the installation and call Premier Mounts at (800) 368-9700.
UNI/UNIE Hardware
5
16˝ x 3˝ Lag Bolts
(Qty 4)
¼˝ Nylon Spacer
(Qty 2)
Square Washers
(Qty 4)
M4 x 10mm
Security Screws for
FTP Install (Qty 4)
M6 x 12mm Security
Screws for PDS
Install (Qty 2)
UNI/UNIE
Features
Premier Mounts’ universal short-throw projector arm (UNI/UNIE) is one of the most exible and installer-friendly short-
throw arms on the market. It adjusts from 7” to 27” [up to 67” from the wall when used with an arm extension (UNIE)].
To make installatins even easier, an array of mounting points at the top and bottom of the GearBox™ allows you to
mount the UNI/UNIE off-center from the whiteboard/screen, if needed. The UNI/UNIE mounts to a single stud or dual
studs at 16”, 18” or 24” spacing, and includes a Fine-Tune Projector (FTP), PDS or SpiroLock™ projector mount.
UNI
UNIE
A/V Equipment
Security
Patent-pending
GearBox™ for
PC, Mac mini™ or
control modules
is secured with
Lock-It™ security
hardware
Universal Projector
Capability
Attach an FTP, PDS
or SpiroLock™
universal projector
mount to t most
short-throw
projectors on the
market.
Cable Routing
Discreetly manage
signal and power
cables through the
arm and into the
GearBox™
Flexible Mounting
Options
Mounts to dual wood
studs (16”, 18” or 24”
spacing)
Arm Extension
Optional arm
extension extends
the projector up to
67” from the wall
Page 4 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions
Installation Instructions Visit the Premier Mounts website at http://www.mounts.com Page 5
Measure distance from center of lens to the top of the projector mounting bracket (C).
® Add the distance from the ground to the top of the screen (A). Add the projector manufacturers recommended
offset from the projector manual (B), then add the measurement from Step 1 (C). Lastly, add 2.5” if you are using
a PDS mount, 2.8” if SpiroLock™ or 3.8” if FTP.
(Example: A + B + C + 2.5˝ or 2.8” or 3.8” = ?)
¯ Add the measurements to determine the mounting height mark. Place a mark at the top of the total calculated
height measurement starting from the ground up. This mark will represent the lower edge of the wall plate.
Refer to the projector’s user’s manual to determine the offset of the projector lens to the top of the
screen/whiteboard (B).
Lens
Projector Bracket
Projector
The UNI/UNIE is designed for use with the Fine-Tune Projector (FTP), PDS or SpiroLock™ projector mounts. In
order to determine the installation height and throw distance, their projector mounting bracket must be mounted
to the projector. Please refer to the projector mount installation instructions prior to performing the following
steps.
Top of Screen
Mark
Legend
A - Distance from ground to the top of the
screen/whiteboard (viewable area).
B - Manufacturers recommended offset
measurement. This measurement will
be listed in the Users Manual.
C - Center of the lens to the top of the
projector bracket.
Add 2.5˝ (PDS), 2.8” (SpiroLock™) or
3.8” (FTP) to the calculated total.
This total distance will be the location for
the bottom rail on the wall plate.
Proceed to the “Wood Stud Installation”
section.
Ground
Determining the Installation Height
UNI/UNIE
+2.5"/+2.8"/+3.8"
Page 6 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions
UNI/UNIE
THE EXACT CENTER OF THE STUD MUST BE LOCATED FOR CORRECT AND SAFE INSTALLATION.
Use an electronic stud nder (not supplied) to
locate the center of the stud that is in the wall. Wood Stud
Stud nder
Height
Mark
(from page 5)
Wood Stud
Marking
Wall
Plate
Do NOT over-tighten lag bolts when attaching the mount to the wall. Improper installation may result in personal
injury or damage to property.
Once the mounting points have been marked, use a
¼˝ drill bit and portable drill to drill the pilot holes.
Drill Marking
Wood Stud Installation
Mounting Point
Mark
Step 1
Step 2
Step 4
Use a pencil to mark the rst mounting point, just
above your height mark (from page 5).
Step 3
Use the level to make sure the wall plate is level from
side to side.
® Place the wall plate over the rst mounting point mark
and use a pencil to mark the rest of the mounting
points.
Four (4) mounting points must be used. Two (2)
upper mounting points and two (2) lower mounting
points.
Installation Instructions Visit the Premier Mounts website at http://www.mounts.com Page 7
Locate the mounting hook cutout on the top of the
wall plate.
® Tilt the arm slightly and gently insert the mounting
hooks into the mounting hook cutouts.
¯ Slowly lower and let the projector arm rest against
the wall plate.
Mounting Hook Cutout
Mounting Hooks
Wall Plate
Projector Arm
MAKE SURE THE PROJECTOR ARM IS FULLY
SEATED BEFORE RELEASING THE UNIT.
Attaching the Projector Arm
UNI/UNIE
If using the storage feature of the product, it
may be easier to route any wiring at this time
(please see Page 15).
After the pilot holes have been drilled, use four (4)
5
16˝ x 3˝ lag bolts and four (4) square washers to
mount the wall plate to the wooden studs.
Use a ½˝ socket and socket wrench to nish this step.
Socket
Lag Bolt and Square Washer
Wall
Plate
Proceed to the “Attaching the Projector Arm”
section.
Back Plate Covers
Step 6
Step 5
Insert and gently tap the upper and lower back plate
covers into place.
Step 1
UNI/UNIE
Locate the two (2) lock mounting points on the
projector arm. These two points will be aligned with
the lock mounting points on the wall plate.
® Using a security wrench, insert and tighten two (2)
M5 x 8mm security head screws.
Do NOT overtighten these screws.
Step 2
Lock Mounting
Point
M5 x 8mm Security
Head Screw
Security Wrench
Page 8 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions
Please review your projector mount’s user manual before attaching the upper
mounting bracket. The correct throw distance (the distance from the projector to the screen) must be
determined prior to mounting the projector.
Refer to the projector’s user’s manual to
determine the distance from the lens to
the front of the screen (X).
® Measure the distance from the front of
the lens to the center of the projector (Y).
¯ Measure the distance from the wall to the
face of the whiteboard/screen (Z).
° Add all measurements (X + Y + Z) to
determine projector placement on the
arm assembly. This measurement
will determine where the center of the
mount bracket will be located on the
arm assembly. Please make note of this
measurement.
Front Lens
Rear Lens
Calculations
X = Manufacturers recommended
throw distance
Z = Distance from wall to face of
whiteboard/screen
Front Lens Throw Distance =
(X + Y + Z)
Rear Lens Throw Distance =
(X - Y + Z)
Throw Distance Calculation
The UNI/UNIE can be also used as
a wall-mounted standard projector mount as
well as a short throw projector mount. Align
the projector facing the opposite direction
from the wall plate to project the image
across the room. Please take into account
the projectors throw capabilities prior to
mounting in the projector opposite direction.
Continue to the “Attaching the Projector
Mount” section.
UNI/UNIE
Installation Instructions Visit the Premier Mounts website at http://www.mounts.com Page 9
What kind of projector mount are you attaching to
the adjustable mounting assembly?
If it is a Fine-Tune Projector (FTP) mount, continue to the
“Installing an FTP Mount” section below.
If it is a SpiroLock™ mount, proceed to the “Installing
an SpiroLock™ Mount” below.
If it is a PDS mount, proceed to the “Installing a PDS
Mount” section on page 10.
Attach the projector mount to the mounting assembly
before attaching the projector itself.
Attaching the Projector Mount
A
A
A
A
B
Installing an FTP Mount
Detach the upper half of the mounting assembly from
the lower half.
® Following the “A” mounting-hole pattern (Figure 1),
use four (4) M4 x 10mm security screws to attach the
FTP projector mount to the lower half of the mounting
assembly (Figure 2). Do not overtighten.
Use the four mounting holes on the collar of the FTP.
¯ Re-attach both components of the mounting
assembly.
Refer to the FTP user manual for instructions on
attaching the projector to the mount.
Installing a SpiroLock™ Mount
Detach the upper half of the mounting assembly from
the lower half.
® Following the “B” mounting-hole pattern (Figure 1),
use one (1) M8 x 16mm athead security screw to
attach the SpiroLock™ projector mount to the lower
half of the mounting assembly (Figure 3). Do not
overtighten.
The M8 x 16mm athead security screw is included
with the SpiroLock™.
¯ Re-attach both components of the mounting
assembly.
Refer to the SpiroLock™ user manual for instructions
on attaching the projector to the mount.
Figure 1
Figure 2
Figure 3
Bottom view of the adjustable
mounting assembly
M4 x 10mm security screw
M8 x 16mm athead
security screw
Are you attaching an extension arm?
If yes, continue to the “Extension Arm Installation
(Optional)” section on page 12.
If no, proceed to the “Adjustable Mounting
Bracket Installation” section on page 13.
Are you attaching an extension arm?
If yes, continue to the “Extension Arm Installation
(Optional)” section on page 12.
If no, proceed to the “Adjustable Mounting
Bracket Installation” section on page 13.
UNI/UNIE
Page 10 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions
Installing a PDS Mount
Attaching the Projector Mount (cont’d)
C
C
Figure 1
Bottom view of the adjustable
mounting assembly
Figure 2
Detach the upper half of the mounting
assembly from the lower half.
® Following the “C” mounting-hole pattern
(Figure 1), use two (2) M6 x 12mm
security head screws to attach the PDS
base box to the lower half of the mounting
assembly (Figure 2).
You must insert the screws from the
bottom of the PDS base box. Detach the
base box from the mount, if needed.
¯ Re-attach both components of the
mounting assembly.
Refer to the PDS user manual for
instructions on attaching the projector to
the mount.
.
Do NOT overtighten these screws.
M6 x 12mm security
screw
How will you attach the PDS mount?
If you are using the adjustable mounting assembly,
continue to the “Attaching the PDS to the
Adjustable Mounting Assembly” section below.
If you are using only the upper mounting plate for an
even lower prole, proceed to the “Attaching the
PDS to the Upper Mounting Plate” section on
page 11.
Attaching the PDS to the Adjustable Mounting
Assembly
Are you attaching an extension arm?
If yes, continue to the “Extension Arm
Installation (Optional)” section on
page 12.
If no, proceed to the “Adjustable
Mounting Bracket Installation” section
on page 13.
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Premier Mounts Rack & Stand Handbücher
Premier Mounts
Premier Mounts LPSA3747 Bedienungsanleitung
Premier Mounts
Premier Mounts CTM-MS1 Bedienungsanleitung
Premier Mounts
Premier Mounts PP-FCTA-QL Bedienungsanleitung
Premier Mounts
Premier Mounts PTM Bedienungsanleitung
Premier Mounts
Premier Mounts FPS-200 Bedienungsanleitung
Premier Mounts
Premier Mounts AM100 Bedienungsanleitung
Premier Mounts
Premier Mounts LMVLF Bedienungsanleitung
Premier Mounts
Premier Mounts Universal Flat Mount FM3 Bedienungsanleitung
Premier Mounts
Premier Mounts Convergent Series Bedienungsanleitung
Premier Mounts
Premier Mounts RFM Bedienungsanleitung
Premier Mounts
Premier Mounts USA Bedienungsanleitung
Premier Mounts
Premier Mounts AM100 Bedienungsanleitung
Premier Mounts
Premier Mounts Press and Release LMVP Bedienungsanleitung
Premier Mounts
Premier Mounts MVWC-2X2 Bedienungsanleitung
Premier Mounts
Premier Mounts ECM-3763D Bedienungsanleitung
Premier Mounts
Premier Mounts PCM-MS2 Bedienungsanleitung
Premier Mounts
Premier Mounts PDS-PLUS Bedienungsanleitung
Premier Mounts
Premier Mounts PRC Bedienungsanleitung
Premier Mounts
Premier Mounts SOAD Bedienungsanleitung
Premier Mounts
Premier Mounts VPM Bedienungsanleitung
Beliebte Rack & Stand Handbücher anderer Marken
Salamander
Salamander Acadia AC/W/L400/WH Bedienungsanleitung
Fohhn
Fohhn VAT-09 Benutzerhandbuch
ricoo
ricoo FS0522 Bedienungsanleitung
AMSOIL
AMSOIL BMK-22 Kurzanleitung
Kargo Master
Kargo Master 48220 Bedienungsanleitung
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung
