Primes FocusMonitor FMW+ Bedienungsanleitung
Revision 01/2018 EN
FocusMonitor FMW+
Additional Documentation to the Operating Manual
FocusMonitor FM+
35,0(6
Short Start Guide
Translation of the Original Instructions
FocusMonitor FMW+
3
Revision 01/2018 EN
35,0(6
IMPORTANT!
READ CAREFULLY BEFORE USE.
KEEP FOR FUTURE USE.
FocusMonitor FMW+
4
Revision 01/2018 EN
35,0(6
Contents
1 About this documentation 5
2 Distinguishing features in comparison with the standard device 5
3 Connections 5
4 Status display 6
5 Adapt device 6
5.1 Inserting the measuring tip ........................................................................................................7
6 Hinweise zum Absorber 9
7 Mounting/Dismounting 9
7.1 Installation position....................................................................................................................9
7.2 Alignment..................................................................................................................................9
8 Electrical connection 10
8.1 Connection to the PC/LAN and establishing the power supply................................................10
9 Measuring with the LaserDiagnosticsSoftware LDS 11
9.1 Single plane measurement ......................................................................................................11
9.2 Caustic measurement .............................................................................................................15
9.3 Measuring mode Monitor ......................................................................................................20
10 Declaration of conformity 24
11 Technical data 25
12 Dimensions 26
13 Appendix 27
13.1 Exchanging the measuring tip ................................................................................................27
13.2 Exchanging the detector .........................................................................................................29
FocusMonitor FMW+
5
Revision 01/2018 EN
35,0(6
1 About this documentation
This documentation describes the special version „FocusMonitor FMW+“ of the PRIMES measuring device
“FocusMonitor FM+” and presents the differences. It supplements the standard operating manual of the
FocusMonitor FM+.
IMPORTANT!
Please pay special attention to the safety instructions given in the standard operating manual of the
FocusMonitor FM+.
2 Distinguishing features in comparison with the standard device
• The FocusMonitor FMW+ does not have an integrated z-axis. For the measurement the focus is moved
along the axis by the system. Information regarding the z-position can either be entered manually via the
settings dialogue (measurement >> single measurement) in the LaserDiagnosticsSoftware.
• An absorber is integrated into the measuring device (maximum absorber power of 1000 watts).
• The maximum energy per measurement is 90kJ (max. irradiation time=90s at 1000Watt).
• The measuring device does not have a protective gas connection
• Direct connection to the PC via Ethernet.
3 Connections
LED display
On/off switch
Ethernet connection RJ-45
Power supply connection
Fig. 3.1: Connections of the FMW+
FocusMonitor FMW+
6
Revision 01/2018 EN
35,0(6
4 Status display
The different operating modes are indicated by three LEDs.
Designation Color Meaning
Measuring Red Measurement is running
Rotation Orange Motor is running
Power White Voltage is applied (24V)
5 Adapt device
Depending on the laser type the corresponding measuring tip and a suitable detector have to be used. The
DFIG-PS+ detector is included ex works; the measuring tip has to be mounted by the customer.
Detector
type
Laser Type of Sensor Amplification Wavelength range in μm
DFC+ CO2Pyro-detector 1 9 − 12
DFY-PS+ NIR/VIS Photodiode Automatic adaptation of the sensitivity 0.4 − 1.1
DFIG-PS+ NIR Photodiode Automatic adaptation of the sensitivity 1 − 2.1
Tab. 5.1: Variety of detectors
Measuring tip High Power CO2High Div YAG Diode Tip
Typical pin hole diameter in µm 20-25 20 50
Beam divergence/acceptance angle in mrad < 240 < 200 < 500
Typical wavelength in µm 9-12 0.4-1.1 0.4-1.0
CO2Laser
Max. power density*)in MW/cm230 — —
Max. power in kW 1 — —
Nd:YAG Laser
Max. power density*)in MW/cm2— 10 1
Max. power in kW — 1 1
Diode Laser
Max. power density in MW/cm2— 1 1
Suitable Detectors
Detector type DFC+ DFIG-PS+, DFY-PS+ DFIG-PS+, DFY-PS+
Tab. 5.2: Variety of measurement tips and detectors
*)Please note the damage threshold in the Operating Manual FocusMonitor FM+.
FocusMonitor FMW+
7
Revision 01/2018 EN
35,0(6
5.1 Inserting the measuring tip
To prevent transport damage, the measuring tip is disassembled when delivered. It is to be installed with the
curved part facing towards the beam source.
There are different measurement tips available for different wavelengths (see Tab. 5.2 on page6).
NOTICE
Danger of damaging the measuring tip
The small drill hole in the measuring tip can be blocked easily by dirt particles or by
touching it with bare hands.
When mounting/dismounting the tip, please wear powder-free latex gloves and ensure a
dirt- and dust-free environment.
1. Turn off the supply voltage.
2. Turn the drive wheel (see Fig. 5.4) clockwise until the disc extends approx. 15mm into the measuring
window in a positive y-direction.
Drive wheel
Disc with measuring tip retaner
Fig. 5.1: Moving the disc into the measuring window
3. Turn the disc until the measuring tip retainer becomes visible in the opening of the housing.
4. Remove the fastening screws (Torx T8) as well as the retaining plate.
5. Carefully insert the new measuring tip in the disc (caution, the entrance aperture is located on the arched
side of the tip, see Fig. 5.2).
FocusMonitor FMW+
8
Revision 01/2018 EN
35,0(6
Entrance aperture
Fig. 5.2: Entrance aperture (pinhole) in the measuring tip
Fig. 5.3: Inserting the measuring tip
6. Insert the retaining plate in the disc with the guidance groove pointing upwards and an angle of 45 de-
grees and press it downwards into the opening (see Fig. 5.4).
Fig. 5.4: Inserting the retaining plate
7. Insert the screws and fasten them hand-tight.
8. Move the measuring tip out of the measuring window to ensure it is protected.
When turning the supply voltage back on, the measuring head automatically moves back into its
resting position.
FocusMonitor FMW+
9
Revision 01/2018 EN
35,0(6
6 Notes on the absorber
The high-power absorber can absorb an energy application of 90 kJ (1000 W · 90 s).
NOTICE
Risk of damage caused by overheating
The absorber is equipped with an alarm siren that warns of overheating. It activates when
the absorber casing reaches a temperature of 60 °C.
In case of alarm, immediately turn off the laser and allow the absorber to cool!
NOTICE
Risk of burns
The laser beam can make the surface of the absorber very hot.
Do not touch the absorber during or immediately after a measurement!
7 Mounting/Dismounting
7.1 Installation position
The FMW+ was designed for a vertical beam incidence from above.
7.2 Alignment
1. When positioning the device in x- and y- direction,
please make sure that the laser beam hits the
center of the semi-circle in the inlet aperture.
RS 232
Air in
Air out
24 V
Power
Data
Send
Trigger
Position of the laser beam
FocusMonitor FMW+
10
Revision 01/2018 EN
35,0(6
8 Electrical connection
The FMW+ requires a voltage supply of 24VDC for the operation. A suitable power supply is included in the
scope of delivery. Use only the included cable to connect the power supply with the local power supply.
Data is transmitted between the FocusMonitor FMW+ and PC/LAN via the Ethernet connection.
8.1 Connection to the PC/LAN and establishing the power supply
Zeichnungsname:
Zeichnungsnummer:
Bearbeiter:
Erstellungsdatum:
Druckausführung:
Maßstab:
FM-W-Plus-Deckplatte
FMW02P0004D
M.Werner
22.12.2016
einfarbig weiss
1:1
Geprüft von: Ch. Gerhardt Datum: 06.10.2017
Index Änderung Name Datum
2 Änderung der Fertigungszeichnung/Bedruckung M. Werner 04.10.2017
1 Änderung der Fertigungszeichnung/Bedruckung M. Werner 04.05.2017
Offset: 10.6 mm
Measuring
Rotation
Power
x+
-
+
yFMW+
FocusMonitor Ethernet
Power In
Ethernet crossover cable
Ethernet
PC
FMW+
PRIMES power supply
Fig. 8.1: Connection of FMW+
Connect the FMW+ to the PC via a crossover cable or to the network via a patch cable.
Inhaltsverzeichnis
Andere Primes Messgerät Handbücher
Primes
Primes MSM+ Bedienungsanleitung
Primes
Primes PowerMonitor PM Series Bedienungsanleitung
Primes
Primes PMT 01 Bedienungsanleitung
Primes
Primes PROFINET Bedienungsanleitung
Primes
Primes LQM series Bedienungsanleitung
Primes
Primes PowerMonitor PM Series Bedienungsanleitung
Primes
Primes CUBE Bedienungsanleitung
Primes
Primes Cube L1 Bedienungsanleitung
Primes
Primes ScanFieldMonitor SFM Bedienungsanleitung
Primes
Primes PMC-C Bedienungsanleitung
Primes
Primes LQM+ 20 Bedienungsanleitung
Primes
Primes PocketMonitor Bedienungsanleitung
Primes
Primes MSM Bedienungsanleitung
Primes
Primes PMC-BEO Bedienungsanleitung
Primes
Primes BM+ 60 Bedienungsanleitung
Primes
Primes Cube M Bedienungsanleitung
Primes
Primes PowerMeasuringCassette PMC Bedienungsanleitung
Primes
Primes PowerLossMonitor PLM Series Bedienungsanleitung
Primes
Primes Cube L1 Bedienungsanleitung
Primes
Primes Cube L1 Bedienungsanleitung
