Princeton VL1919 Bedienungsanleitung

INTRODUCTION

This manual will familiarize you with the installation and use of your PRINCETON VL1919 LCD

Monitor, Please take the time to look through these instructions even if you are familiar with

monitors.

We have taken all possible care to ensure that this manual contains correct, accurate

information. However, the manufacturer cannot assume liability for any possible errors. In addition,

the manufacturer cannot guarantee that the hardware will meet the purpose you require.

any form (print, photocopy, microfilm or any other process) or processed by an electronic system

without prior written permission from the manufacturer.

We reserve the right to make changes according to technical progress. PRINCETON VL1919 is an

internationally registered trademark. Other brand names may be registered trademarks and must be

treated as such.

Important Safety Instructions

Do not place the monitor in very hot or cold, or damp or dusty surroundings. Do not put vases etc. on

the monitor (water may cause short circuits). Do not block or cover the ventilating openings. All

products that produce magnetic fields, i.e. laser printers, loud speakers, etc., must not be placed

close to the monitor. Do not install this monitor in areas where too much light or sunshine might

directly hit the screen, otherwise the brightness of the picture will be poor due to reflections.

Refer all servicing and maintenance to authorized service personnel only!

CAUTION

Do not remove the cover!

Serious electrical shock hazards exist inside this monitor.

NOTE

Removal of cover invalidates your warranty.

TABLE OF CONTENTS

INTRODUCTION 1

TABLE OF CONTENTS 2

IMPORTANTINFORMATION 3

CARING FOR YOUR LCD MONITOR 4

WALLMOUNTING 4

UNPACKING 5

CONNECTING 5

STARTUP 6

BASIC SETUP 7

IMAGE SETTINGS USING THE OSD MENU 7

OSD MENU FUNCTIONS 8

TROUBLESHOOTING 14

TECHNICAL SPECIFICATIONS 15

CONFORMITY AND COMPLIANCE 16

IMPORTANT INFORMATION

Note on monitor placement

 The setup location must not be extremely hot, cold, humid or dusty. Heat and cold can impair

the functionality of the monitor. Humidity and dust can cause the monitor to fail.

 Don’t place the monitor near heaters such as radiators or the like. Don’t expose the monitor to

mechanical vibration or jarring.

 Position the monitor so that no direct light or sun strikes the screen, which could cause

reflections that reduce the quality of the image.

Notes on power connection

 Only use the power cord designated for use in your country. The wall outlet should

be within easy reach. Pulling the power plug is the only way to disconnect

the monitor from the power source.

 This monitor is ENERGY STAR®-compatible, and guarantees that this device

complies with the ENERGY STAR® guidelines for optimizing power consumption.

Safety instructions for operation

 The power cord must not be damaged. Do not place any objects on the power cord

and make sure it does not have any knots. To unplug the cord, always pull on the plug

and not on the cable itself. Damage to the power cord may result in fire or cause electric

shocks.

 Avoid covering the ventilation slots. Air circulation is necessary to prevent the

monitor from overheating. If the air circulation is restricted it could cause fire or

damage the monitor.

 Do not use any solvents to clean the monitor, as the housing could be damaged.

For more information about cleaning the monitor, please see “Caring for Your

LCD Monitor”.

 Never open the monitor housing on you own. There is a danger of electric shock and

other hazards. The monitor may only be opened and serviced by qualified

professionals.

Note on resolution

All resolutions provided by the graphics card that deviate form the physical resolution of the panel

are adjusted by interpolation. This can impair the image quality.

Notes on ergonomics

To protect your eyes, neck and shoulder muscles when working with a computer, we

recommend that you maintain a viewing distance of between 50 and 75 cm from the monitor.

Furthermore, you should regularly focus on an object around 6 m away from you to help your

eyes relax. Ergonomically, your posture is best when elbows, pelvis, knees and ankles are

all at right angles.

CARING FOR YOUR LCD MONITOR

 First, unplug the power cord from the wall socket

 If the LCD screen is extremely dirty, clean it with a moist cloth. Use only warm water and then

wipe the monitor dry. Solvents or harsh cleaners can damage the housing. Clean the display

surface only with a soft cloth, otherwise you may damage the display’s coating

 If the monitor is only slightly dirty, clean it using a soft, dry and antistatic cloth.

 The LCD monitor’s screen surface is very sensitive. Please avoid any contact with the

surface (finger, pencil, etc.) and be especially cautious during transportation since

jolts and shocks can cause the screen to become scratched (always use the original

packaging).

WALL MOUNTING

The PRINCETON monitor is shipped with the standard desktop configuration. However, you can optionally

mount the device on a wall or on a monitor swivel arm (optional accessory). Please follow the

corresponding instructions (4-hole assembly with a spacing of 4 ×4 inches (100 ×100 mm)according

to the international VESA FDMI standard).

UNPACKING

Carefully lift the monitor out of the packaging and make sure that all components are included (see fig. 1).

Save the original box and packing material in case you have to ship or transport the monitor. To set up the

device, you must fit the monitor base together.

Figure 1.LCD Monitor

CONNECTING

➧To connect the monitor to your PC

1. Make sure that the PC and the monitor is unplugged.

2. Connect the 15-pin signal cable to the monitor and The PC (see fig. 2)

3. If you have a graphic card with a digital DVI-D connector(24-pin socket), then connect one end

of the DVI-D cable to the DVI-D connector of your monitor (see fi g. 2b), the other end to the

computer.

Figure 2.Connecting the monitor to the PC

Signal coble

➧Connecting the audio cable

If your computer is equipped with an audio output port, connect one end of the sound cable to the audio

Input connector of the monitor (①in fig. 3) and the other end to the Line-Out connector of the computer.

➧To connect the monitor to the power source

Connect the separate power cable (②in fig. 3) to the Monitor and a grounded outlet.

Figure 3.Connecting the monitor to the power source

STARTUP

1. First start your PC and then turn on your monitor using the power switch (④in fig. 4). The status

indicator (④in fig. 4) should light up green.

2. Adjust the image to meet your requirements (see the following sections “Basic Setup”and

“Image settings using the OSD menu”).

3. If there is no image displayed on the monitor, consult the section “Troubleshooting”.

Cable DVI-D

BASIC SETUP

➧Automatic Image Adjustment

You can adjust the image settings (such as brightness, contrast, image position, phase, etc.)

manually or by using the LCD monitor’s automatic image adjustment feature. This will adjust

the image parameters to their optimal settings for the current graphics mode. Press

SELECT/AUTO (①in fig. 4) to launch the automatic adjustment. The process will take a short

while until completed.

➧Setting the volume directly

You can adjust the speaker volume of the integrated audio system directly by pressing the ◄or

►buttons (③and②in fig. 4) while the OSD menu is inactive. Next press the ►button to increase

the volume or the ◄button to decrease it.

➧Shortcut for adjusting brightness and contrast

You can adjust brightness and contrast directly by pressing the ▲or ▼buttons (⑥and⑤in fig. 4)

while the OSD menu is not displayed. Next, press the ▲or ▼buttons (⑥and⑤in fig. 4) to adjust the

brightness or the ◄or ►buttons (③and②in fig. 4) while the OSD contrast.

➧Disabling the sound (MUTE)

You can mute sound playback by pressing the ◄or ►buttons (③and②in fig. 4) while the OSD

menu is not displayed. Next, press the ▼button to mute the sound or the ▲button to reactivate it.

1. IMAGE SETTINGS USING THE OSD MENU

The OSD menu is a window on your screen that allows you to view and change display settings. To change

an OSD setting:

Figure 4.Monitor features

Press the MENU button (⑤in fig. 4) to display the OSD menu on the screen.

1. There are a total of 5 OSD submenus divided by categories. Select the desired submenu by

pressing the OSD button < or > (①and ②in fig. 4; see section “OSD Menu Functions”).

2. Press the OSD button MENU (⑤in fig. 4) to activate the selected function or associated submenu.

3. If you selected submenu, now select the sub-function you want using < or > (①and ②in fig. 4)

4. Set the desired value using the OSD button < or > (①and ②in fig. 4)

5. The current settings are automatically saved when you return to the previous level or exit the OSD

menu. Repeat steps 2–5 to make further adjustments as needed.

6. The OSD menu automatically disappears if no changes are made for more than 45 seconds

(default setting). The current settings will be saved. You can close it manually by pressing the

button AUTO (⑥in fig. 4).

2.OSD Structure

2.1 Menu Items

2.2 Messages

Message

Audio Status

+- Audio Status: mute

+- Audio Status: normal

Auto Adjust

+- Auto processing

Input Status

+- Input: Analogue

+- Input: Digital

No Signal

+- No signal

Going to sleep

OSD locked

+- OSD locked

Power button locked

+- Power button locked

+- Power button unlocked

Out of Range

+- Frequency out of range: ## kHz / ## Hz

Please change the display mode to

1280 x 1024 with 60 Hz.

Resolution notice

+- For best picture quality, please

change resolution to 1280 x 1024.

SELECT:Disable EXIT:Clear

2.2.1 Message window style and size

Size 1: 290 x 94 pixels:

-Input select message window to be defined-

Size 2: 360 x 140 pixels for Resolution notice and out of range message:

2.2.2 Message location

All messages are centered on the screen.

2.2.3 Message time-out

All messages are disappearing automatically after 3 seconds, except:

 Resolution notice message keeps until end user either disables or exits message

 Out of range message keeps until monitor enters to PS mode

3 Function description

3.1 Start up logo

When the monitor is switched on, the FSC logo is shown in center of screen with a black screen for about 2

seconds.

3.2 Key response

All changes of options with adjust bars will take place immediately. Also the color temperature menu shows

immediate response, when the selection cursor is moved. All other options are stored when EXIT is

pressed.

Andere Handbücher für VL1919

Inhaltsverzeichnis

Andere Princeton Monitor Handbücher

Princeton

Princeton SENergy 714 Bedienungsanleitung

Princeton

Princeton ULTRA97 Bedienungsanleitung

Princeton

Princeton LCD1908 Montageanleitung

Princeton

Princeton LCD1516 Montageanleitung

Princeton

Princeton LCD Flat Panel TV LCD 1911 Montageanleitung

Princeton

Princeton LCD17M Bedienungsanleitung

Princeton

Princeton 1700PD Montageanleitung

Princeton

Princeton VL2418W Bedienungsanleitung

Princeton

Princeton VL2018W Bedienungsanleitung

Princeton

Princeton LCD1711 Bedienungsanleitung

Princeton

Princeton VL1919 Montageanleitung

Princeton

Princeton LCD2000 Bedienungsanleitung

Princeton

Princeton LCD17D Bedienungsanleitung

Princeton

Princeton VL2418W Montageanleitung

Princeton

Princeton LCD1700 Bedienungsanleitung

Princeton

Princeton VL1514 Bedienungsanleitung

Princeton

Princeton LCD Flat Panel TV LCD 1708 Montageanleitung

Princeton

Princeton LCD1711 Montageanleitung

Princeton

Princeton VL154 Bedienungsanleitung

Princeton

Princeton AGX700 Bedienungsanleitung

Princeton

Princeton LCD 1912 Montageanleitung

Princeton

Princeton LCD Flat Panel TV PD Montageanleitung

Princeton

Princeton W1901PD Montageanleitung

Princeton

Princeton LCD1950 Bedienungsanleitung

Beliebte Monitor Handbücher anderer Marken

Linear Acoustic

Linear Acoustic LQ-1000 Bedienungsanleitung

AOC

AOC I2579V Bedienungsanleitung

Gateway

Gateway FPD1520 Bedienungsanleitung

Furuno

Furuno Mu 120c Bedienungsanleitung

Asus

Asus VB171D - 17" LCD Monitor Bedienungsanleitung

Dell

Dell S2230MX Gebrauchsanweisung

Philips

Philips 107C64 Bedienungsanleitung

Dell

Dell S2409WFP Bedienungsanleitung

EverFocus

EverFocus EN-7517E Bedienungsanleitung

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Bedienungsanleitung

Dell

Dell Precision 7680 Bedienungsanleitung

LG 50PM1M - - 50" Plasma Panel Bedienungsanleitung

Bosch

Bosch DDU 9 Bedienungsanleitung

Acer

Acer A231HL Bedienungsanleitung

Philips

Philips 86BDL4152T Bedienungsanleitung

NEC

NEC AccuSync LCD5V Bedienungsanleitung

Emay

Emay SleepO2 Bedienungsanleitung

IBM

IBM 6360 Montageanleitung