Pro-Ject Audio Systems Amp Box DS2 Mono Bedienungsanleitung

INSTRUCTIONS FOR USE

Pro-Ject Amp Box DS2 Mono

Pro-Ject Audio Systems · Pro-Ject Amp Box DS2 Mono (from SN: 17A004755) · Revision 2017.03.07

Dear music lover,

Thank you for purchasing an amplifier from Pro-Ject Audio Systems.

In order to achieve maximum performance and reliability you should study these instructions for use carefully.

Warning of a hazard for the user, the unit or possible misuse

Important notice

Safety instructions

AC outlet voltages vary from country to country. Before connecting to the mains, make sure that the

voltage in your area meets the voltage requirements printed on the power supply. The power cord is

used to disconnect the unit from the mains. Make sure that the power cord is easily accessible at all

times. Never handle the device, the power cord/power supply while your hands are wet or damp.

Avoid letting liquids enter the device or the power supply. Never place any item containing liquid,

such as a flower vase on or near the device. Never spill any liquid on the device or the power supply.

Never place any naked flame sources, such as lighted candles on or near the device. The product shall not

be used in damp or wet locations, next to a bathtub, sink, swimming pool or any other similar conditions.

Tubes produce heat. Proper ventilation has to be guaranteed all the time. The unit must not be stacked.

Connectors

Make all connections whilst the amplifier is disconnected from the power supply.

The red speaker terminals carry the positive signal (+), the black speaker terminals the negative

signal (–). Make sure the polarity of the connection is correct at each end of the cables.

Only connect one loudspeaker with an impedance not less than 4 ohms per channel.

Never use any other power supply than the one supplied with the unit.

Connection to the preamplifier

The RCA/cinch socket marked

Input

is for connecting the cable from your pre-amp or AV processor. Socket

marked

Bypass

are input bypass.

Connection to the speakers

The output terminals accept loudspeaker cables terminated with 4mm ∅Banana plugs, spades connectors

or naked wire.

Mains power connection and methods to switch the unit on and off

Connect the low voltage plug from the power supply to the

2x48V=

socket of the amplifier

before

connecting the power supply to the mains. Amp Box DS2 Mono can be switched on and off by using 2

different methods which are equal in priorities.

1. Using front pushbutton to switch on or into standby

The pushbutton on the front panel of the unit alternately turns the power on or returns it to standby mode. The

blue LED on the front panel shows that the unit is powered on.

Please note: If a trigger signal is present Amp Box DS2 Mono can’t be switched off by the

pushbutton.

2. Remote power on - triggers

Amp Box DS2 Mono can be switched on via other Box Design components when a 12V trigger voltage is

present at the 2.5mm socket marked

Trigger Input.

Special power-on cables (polarity ) in diverse

lengths are available as accessories. The remote power-on signal can be relayed to further units via the

Trigger Output

socket. When the 12V trigger signal is switched off, Amp Box DS2 Mono will also switch off.

Trigger cables may only be plugged into the sockets when the amplifier is disconnected from the

power supply and from the mains. Failure to do so may result in damage of the unit.

Technical specifications Pro-Ject Amp Box DS2 Mono

Power output 120W/205W at 8ohm/4ohm (<1% THD)

Frequency response: 10Hz - 50kHz (0dB, -3dB)

Channel separation: >40dB at 20kHz

Noise floor: >90dB

THD <0.1% at 90W

Gain 31dB

Pre in 2 RCA (bypass input-output)

Input sensitivity 550mV (100W, 4ohms)

Input impedance 10kohm

Speaker connectors: 4mm banana plugs

Trigger 12V switching voltage

Trigger in and out 2-pole coaxial 2,5mm jack

Outboard power supply: +-48/2,5ADC, suitable for your countries mains supply

Power consumption: 2,5A DC, <1W in standby

Dimension (W x D x H): 206 x 194 x 68 aluminium;

240 x 194 x 69 wood

Weight (without power supply): 1440g aluminium,

1900g wood

Pro-Ject Audio Systems · Pro-Ject Amp Box DS2 Mono (from SN: 17A004755) · Revision 2017.03.07

Service

Should you encounter a problem which you are not able to alleviate or identify, please contact your dealer for

further advice. Only if the problem cannot be resolved there, the unit should be sent to the responsible

distributor in your country.

Warranty

The manufacturer accepts no responsibility for damage caused by not adhering to these instructions

for use. Modification or changes to any part of the product by unauthorized persons release the

manufacturer from any liability over and above the lawful rights of the customer.

Pro-Ject Audio Systems is a registered Trademark of

H. Lichtenegger.

This guide was produced by: Pro-Ject Audio Systems

The information was correct at the time of going to

press. The manufacturer reserves the right to make

changes to the technical specification without prior

notice as deemed necessary to uphold the ongoing

process of technical development.

Inhaltsverzeichnis

Andere Pro-Ject Audio Systems Verstärker Handbücher

Pro-Ject Audio Systems

Pro-Ject Audio Systems Remote Box S2 Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pre Box S2 Digital Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pro-Ject MaiA DS Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems BOX-DESIGN Vinyl NRS Box S3 Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Phono Box Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Xpression II Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Tube Box SE II Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems MaiA Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Box S USB Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Phono Box USB V Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Amp Box RS Mono Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pre Box S2 Analogue Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Head Box SE II Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Phono Box SE II Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Tube Box DS2 Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Tube Box DS Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems BOX-DESIGN Stereo Box DS2 Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Head Box S2 Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Phono Box II Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Stereo Box S Phono Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Phono Box USB Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Power Box RS Amp Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pro-Ject MaiA DS Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Phono Box Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung