Pro-Lift WMHS-WB Bedienungsanleitung
ThankyouforpurchasingaProͲLIFTWMHS.TheProͲLIFTproductlineisdesignedtoenhanceyour
interactivewhiteboardsandprojectorsorLCD.Pleasefollowallassemblyinstructionscorrectlyto
provideoptimaluse.
OnlyaqualifiedcontractorshouldinstalltheProͲLIFTWMHS.Ifyoudonotunderstandanyofthe
assemblyinstructions,pleasecontactyourlocalreͲsellerorvisitwww.proliftstand.com.
IMPROPERINSTALLATIONCANCAUSEDAMAGETOYOURProͲLIFTANDLEADTOSERIOUSPHYSICAL
INJURY.JOROManufacturingcannottakeanyresponsibilityfordamageorinjuryresultingfrom
improperinstallation.
DonotoperateProͲLIFTWMHSifthereareanyobstructionsbeloworabovethe
board.Doingsomaycauseunitmalfunctionorleadtoseriousphysicalinjury.
ThesuppliedmountinghardwareisforuseontheProͲLIFTstandsonly.Ifyouencounteranyproblems
orinsufficienthardwareduringinstallation,pleasecontactyourlocalreͲseller.
WB Fastener Kit
(ONLY available with WMHS-LCD Models)
Note: Parts may not be exactly as shown and not to scale
(ONLY available with WMHS-WB Models)
LCD Mount Fastener Kit
WMHS Main Frame Kit
M6x12mm SILVER Button Head
10x
Machine Screw Insulator
6x
WMHS - WMHS-WB ASSY Instructions : 0.004
16x
M6 x 8mm Socket Cap Screw
Wire Mgmt Molding
4x
JORO Button Head
16x
5/16 Hex Nut
8x
Head Self Tapping Screw
#12 x 2" Slotted Washer
12x
M6 Hex Nut
4x
Nylon Washer
6x
3/16" Allen (Hex) Key
1x
2x
#8 x 3/4" Pan Head Wood Screw
5/16" Washer
4x
5/16x1" Button Head
4x
M5 Allen (Hex) Key
1x
JORO Button Head
8x
5/32" Allen (Hex) Key
1x
4x
Thread-Cutting Screw (8-32 x 3/8" Lg.)
8x
M6 x 20mm Socket Cap Screw
Low Profile
2x
Nylon Cable Clip 5/16''
2x
Nylon Cable Clip 1/4''
1/4" Washer
4x
18x
M6 x 20mm Socket Cap Screw
Low Profile
5/32" Allen (Hex) Key
1x
5/32" Allen (Hex) Key
1x
Board Backer Support
2x
2x
#8 Zinc Wall Anchor
JORO Button Head
8x
COPYRIGHT 2017
www.proliftstand.comwww.joromfg.com
WMHS - WMHS-WB ASSY Instructions : 0.004
For ease of installation, do this step prior to mounting WMHS
Carefully ease out the power cable and switch assembly through panel window
Be sure to NOT pull with excessive force
Switch Assembly
Power Cable - Male End
Panel Window
1
COPYRIGHT 2017
www.proliftstand.comwww.joromfg.com
Be sure to fasten Sacrificial Surface to at least three joists
WMHS - WMHS-WB ASSY Instructions : 0.004
Sacrificial Surface
(recommended
3/4" thick)
Min.
35.5 Recommended
" Ceiling Height96
Recommended
24
Min.24
Recommended
2
COPYRIGHT 2017
www.proliftstand.comwww.joromfg.com
WMHS - WMHS-WB ASSY Instructions : 0.004
Mark out the two screw locations to hang the WMHS
Pre-drill pilot holes at the two locations
Be sure both points are horizontal and level
Slotted Hex Washer Head Screw
Fasten the two Slotted Hex Washer Head Screws in the pre-drilled holes
Allow3/8"Min.distance
fromsacrificialsurfaceto
hangWMHS
Slotted Hex Washer Head Screw
Slotted Hex Washer Head Screw
(recommendedfor8'ceiling)
54
20.625
3
COPYRIGHT 2017
www.proliftstand.comwww.joromfg.com
Slotted Hex Washer Head Screw
WMHS - WMHS-WB ASSY Instructions : 0.004
Slotted Hex Washer Head Screw
Add the Slotted Hex Washer Head Screws to upper flat bar
(3 per either side of WMHS is recommended)
Temporarily plug in WMHS and raise the mechanism to
access upper flat bar slots
Be sure previous steps are completed and WMHS is
securely fastened to wall prior to operation
Be sure WMHS is securely fastened to wall by tightening all
Slotted Hex Washer Head Screw
Lower mechanism back to lowest position and unplug
before continuing to next step
Slotted Hex Washer Head Screw
Add the Slotted Hex Washer Head Screws to lower flat bar
(2 per either side of WMHS is recommended)
MUST fasten Slotted Hex Washer Head Screws
through the hole on the flat bar to prevent sliding
Be sure WMHS is securely fastened to wall by tightening
all Slotted Hex Washer Head Screws
Hang the WMHS on the two
Slotted Hex Washer Head Screw
4
COPYRIGHT 2017
www.proliftstand.comwww.joromfg.com
WMHS - WMHS-WB ASSY Instructions : 0.004
Mount the WB Hangers (WMHS-ACC-WBH)
Be sure to NOT over tighten
BE AWARE the mounting position of the WB Hanger is dependant on projector/white
board combination
WMHS-ACC-WBH
M6 x 8mm Socket Cap Screw
Be sure to use the M6 x 8mm Socket Cap Screw screws provided
WMHS-ACC-WBH
UpperMountingPosition
LowerMountingPosition
5
COPYRIGHT 2017
www.proliftstand.comwww.joromfg.com
Mount the Turret Head
Be sure to NOT over tighten
WMHS - WMHS-WB ASSY Instructions : 0.004
M6 x 8mm Socket Cap Screw
Be sure to use the M6 x 8mm Socket Cap Screws provided
6
COPYRIGHT 2017
www.proliftstand.comwww.joromfg.com
Dieses Handbuch passt für folgende Modelle
1
Andere Pro-Lift Whiteboard Handbücher
Beliebte Whiteboard Handbücher anderer Marken
EGAN
EGAN GlassWrite TableScreen TSG Bedienungsanleitung
Claridge
Claridge Edify Mobile Bedienungsanleitung
Legamaster
Legamaster e-Board Touch 2 Bedienungsanleitung
Nureva
Nureva WALL Bedienungsanleitung
Best-Rite
Best-Rite Black Splash Bedienungsanleitung
Da-Lite
Da-Lite Cosmopolitan Electrol Bedienungsanleitung