Pro's Kit MT-7029 Bedienungsanleitung

MT-7029

Noise-Filtering Network PoE

Toner & Probe

User’s Manual

2ed Edition

Thank your for your purchase of Pro’sKit MT-7029 Noise-Filtering

Network PoE Toner & Probe. The Toner and Probe set is used to

quickly trace and identify cables or wires within a group without

noise and also check the operation of telephone lines. With proper

use and care, this instrument will provide many years of reliable

service.

OVERVIEW

MT-7029 with EMI filters to eliminate high frequency noise, for which

allows user to quickly locate and verify the cable status and

troubleshoot wiring for continuity, shorts, opens and crossover on

RJ45, Lan cable Cat 5、5e、6 (UTP/STP), RJ11/12 telephone cable

Cat. 3 (2/4/6 pin) & normal solid/stranded wire by alligator clips

patch cord. Telephone line polarity and status (severed lines, the

off-hook

condition, or incoming call ringing) can be indicated and detected

easily as well.

Ideal for all installation and maintenance fields of telecommunication,

networking, datacom, Audio/Video, cable TV, and all weather

cabling, etc.

SPECIFICATIONS

MT-7029 Transmitter specifications

Tone frequency 130KHz

Max. distance of transmission ≧3km

Max. distance of cable map 300m

Max. working current ≦70mA

Tone mode Single tone

Compatible connectors

for RJ45(8 pin)/RJ11(6 pin) cable map test.

RJ45 SCAN socket : for RJ45 locating

individual wire pairs

RJ11 SCAN socket: for RJ11 locating

individual wire pairs

Cable types RJ45 Lan cable Cat 5、5e、6(UTP/ STP)、

RJ11/12 telephone cable Cat 3

(6P/2C/4C/6C)

Function selection 5 Press button switch (POWER、SCAN

PoE

SCAN、TEST/FAST TEST、Ω、POL/TEL)

Continuity test 1 LED (≦300Ω), Coaxial cable & normal

solid/Stranded wire by alligator clips patch

cord.

Max. signal voltage 8Vp-p

Cable map indication 8 LEDs, Fast/Slow dual speed

Shielded indication 1 LED

Telephone line polarity, status

indication 1 Dual color LED

Live telecommunication

equipment test and router test Yes

Voltage protection DC 48V

Auto power off 1 hour

Low battery display 6.5V (Power LED flashes)

Battery type DC 9.0V (NEDA 1604/ 6F22 DC9V ×1pce)

Dimension (L×W×D) 138×80×35 mm

Weight 140g

MT-7029 Receiver specifications

Frequency 130KHz

The Max. working current ≦115mA

Compatible connectors RJ45(8 pin)/RJ11(6 pin)

Function selection 4 Position mode switch (LED、NCV、OFF、

SCAN)

Earphone jack 1

Signal status indication 1 dual color LED & Buzzer

Cable map indication 8 LEDs

Shielded indication 1 LED

NCV indication 1 LED (AC90~1000V，≥50mm，≤100mm)

LED illumination 1 LED

Power indication 1 LED

Battery type DC 9.0V (NEDA 1604/ 6F22 DC9V ×1pcs)

Dimension (L×W×D) 203×50×32 mm

Weight 95g

Accessories RJ45 cable patch cords、RJ11 cable patch

cords、RJ11 to alligator clips patch

cord,earphone, storage bag, user manual

Safety Information

Never use the Transmitter or Receiver on live circuits of

more than DC48V or it will result damage.

Never use the Transmitter, Receiver or test wire if they are

damaged. Inspect the cases and test leads for damage before

use.

Disconnect unused test leads and connectors from the

Transmitter when testing telephone circuits.

Never open the case except to change the battery or the fuse;

no user-serviceable parts are inside.

Turn off the Transmitter or Receiver and disconnect all test

leads before replacing the battery.

Use only a 9V battery, properly installed in the case, to operate

the Transmitter and Receiver.

If this equipment is used in a manner not specified by the

manufacturer, the protection provided by the equipment may be

impaired.

INTRODUCTION

MT-7029 Transmitter：

Do not connect with DC 48V live circuit equipment or it will

result damage.

Figure1. MT-7029 Transmitter Diagram

1.「TEST」: RJ45(8 pin)/ RJ11 (6/4/2 pin) cable mapping test socket.

2.「SCAN」: RJ11(6 pin) socket.

3.「SCAN」RJ45 socket.

Caution! Do not plug in any live cable over DC 48V to the

transmitter socket.

4.「SHORT」Continuity test indication

5.「Ω」Continuity function indicator

6.「SCAN」Locating and isolating cables function indicator

7.「PoE SCAN」Locating and isolating Cables function indicator

8.「POWER/BAT LOW」Power ON/OFF & Battery low indicator

9.「1~8、G」Cable map & Shielded indication

10.「TEST」Cable map & Shielded function indicator

11.「POL－/G，POL＋/R」Phone line polarity indication

12.「POL」Phone line polarity function indicator

13.「CONT」Phone line status/polarity indicator

14.「TEL」Phone line status function indicator

15. 「」Locating and isolating cables function button

16.「」Continuity/short function button

17.「」Power ON/OFF button

18.「」Cable map & Shielded function button

19.「」Phone line polarity function button

20. Battery cover

Figure 2. MT-7029 Receiver Diagram

1. Probe：Used for cable tracing and NCV detection.

2. LED light

3. Power ON/OFF indicator

4. NCV indicator

5. Signal status indicator

6. Volume control

7. Earphone jack Φ3.5mm

8. Function switch (LED/NCV/OFF/SCAN mode)

9. Speaker

10.「」Locating and isolating cables function button

11.「1~8、G」Cable map & Shielded indication

12. RJ45(8 pin)/ RJ11 (6/4/2 pin) cable mapping test socket.

13. Battery cover

OPERATION

Locating and Isolating Cables：

Using MT-7029 to locate and insolate cables using the 130KHz

analog, also trace twisted wires (UTP, STP, Cat 5, Cat 5e, Cat 6)

and telephone line(Cat 3). Use with a patch cord for RJ45 / RJ11

coaxial cable, general cable and various wiring boards can be tested

by using with alligator clip cable.

Warning

• It is not intended to be used on live wires with a DC power

source over DC 48V (e.g., live telephone lines), nor will it work

on wire pairs that are carrying AC signals.

• Use RJ45 SCAN compatible connector for RJ45 cable tracing.

Use RJ11(6 pin) connector for RJ11(6P/6C/4C/2C) cable tracing.

Use RJ11 (6 pin) connector and work with alligator clips for

coaxial cable, general cable and various wiring boards.

Caution

• The position on the MT-7029 lets you use the Receiver to trace

using an analog 130KHz tone. When using the Receiver to

isolate the tone source in the cable bundle or at the patch panel,

the signal might be interfered with or decreased and the signal

will not pass through metal tubes.

• It is not necessary to touch the Receiver’s tip to the cable or

patch panel when searching for the Transmitter’s signal.

• Make sure the black alligator clip of the Transmitter is connected

to the ground before use.

• When using the MT-7029 with earphone to locate and isolate

cables, please keep probe away from the earphone to avoid

interference of resonance effects

• When doing cable locating, if the signal becomes intermittent,

trailed off or interrupted, the receiver may be disturbed by the

harmonics of other devices. Please move your position for better

signal.

• Different PoE injector may cause Receiver signal to be

intermittent, trailed off or interrupted; please move your position

for better signal.

• When doing PoE scan, bigger current consumption, which will

decrease the battery life time, may occur according to different

PoE equipments, and it is normal.

To locate cables, do the following steps (Figure 3)：

1. Connect the black alligator clip of the Transmitter to the ground,

and then connect the red clip to a jack or punch-down block as

shown in Figure 3.

2. As the Figure 3 shown, when push , the red indicator of

“POWER/ BAT LOW” will light up and turn on the power.

SCAN : Press button for cable tracing. When the red

“SCAN” indicator lights up, the cable tracing is working.

PoE Switches SCAN : Press the button twice for PoE

switches cable tracing. When the red “PoE SCAN” indicator

lights up, the cable tracing is working.

PoE SCAN function applicable with PoE switches and network

switches.(In the cable tracing process, if the sound is weak,

perhaps cable did not connect to the PoE switches/network

switches or cable is broken, please switch to "SCAN" mode)

Press button again, stop tracing.

3. As the figure 3 shown, put the receiver function switch at "scan",

the red indicator in the middle will light up, and long press“ ”

on receiver to operate cable tracing function. The tracing sound

will be output from speaker. When put on the earphone, there

will be no sound from speaker, but from the earphone.

4. Use the Receiver to find the cable location from the cable rack,

patch panel, or behind the wall. The closer the cable locates, the

louder signal sound will be. The signal status indicator will

change from red to blue, and the brightness depends on signal

strength. If the blue LED indicator light is not bright, there is no

signal.

5. Adjust the volume control on the receiver to locate the wire pairs

from 0 cm to 15cm.

Figure 3 Locating cables

Isolating Cables:

To isolate the tone source in the cable bundle or at the patch panel,

do the steps as described in the previous section of “Locating

Cables”.

1. Strip the cable’s shield to a length of between 30 to 45

centimeters and divide the wires into two parts. Do the wire

separation to isolate the cables to verify the signal of each part.

If the beeper gets louder and LED lights up, you have located

the position you are looking for.

2. Adjust the volume control from high to low to locate the wire that

more difficult to be identified. Narrowing the length from 15 to 0

centimeters will help to identify the wire pairs more accurately.

3. Repeat the steps of 1 and 2 to isolate the bundled cables.

Caution

•If you cannot locate the MT-7029 signal on 2-conductor cables,

the cable may be shorted or opened. Use the Continuity Test to

check for shorts or opens on coax and non-terminated cables.

If cables are connected to the switches, it may not easy to find

the signal from MT-7029; please try to turn off the switches or

pull out the cable 1 pce a time to check the signal. If signal is still

hard to found, use " " Cable map & Shielded function or " "

Continuity function test to check cable connection.

Inhaltsverzeichnis

Andere Pro's Kit Messgerät Handbücher

Pro's Kit

Pro's Kit MT-4015 Bedienungsanleitung

Pro's Kit

Pro's Kit MT-3112 Bedienungsanleitung

Pro's Kit

Pro's Kit MT-8100 Bedienungsanleitung

Pro's Kit

Pro's Kit MT-7901 Bedienungsanleitung

Pro's Kit

Pro's Kit MT-7028 Bedienungsanleitung

Pro's Kit

Pro's Kit MT-3102 Bedienungsanleitung

Pro's Kit

Pro's Kit MT-7025 Bedienungsanleitung

Pro's Kit

Pro's Kit MT-7601 Bedienungsanleitung

Pro's Kit

Pro's Kit MT-1505 Bedienungsanleitung

Pro's Kit

Pro's Kit MT-3209 Bedienungsanleitung

Pro's Kit

Pro's Kit MT-4616 Bedienungsanleitung

Pro's Kit

Pro's Kit MT-7600 Bedienungsanleitung

Pro's Kit

Pro's Kit MT-3102 Bedienungsanleitung

Pro's Kit

Pro's Kit NT-311 Bedienungsanleitung

Pro's Kit

Pro's Kit TE-8202A-W Series Bedienungsanleitung

Pro's Kit

Pro's Kit MT-7071 Bedienungsanleitung

Pro's Kit

Pro's Kit MT-7601 Bedienungsanleitung

Pro's Kit

Pro's Kit MT-3266 Bedienungsanleitung

Pro's Kit

Pro's Kit MT-7610 Series Bedienungsanleitung

Pro's Kit

Pro's Kit MT-3110 Bedienungsanleitung

Pro's Kit

Pro's Kit MT-7029N Bedienungsanleitung

Pro's Kit

Pro's Kit PD-151 Bedienungsanleitung

Pro's Kit

Pro's Kit MT-4616 Bedienungsanleitung

Pro's Kit

Pro's Kit MT-7071 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung