Prorack K094 Bedienungsanleitung

K094

Fitting Kit

EN Fitting Instructions for Basic Carrier

x 4 x 1 x 4

Revision No: 3C 1

Fitting Kit K094

MAX kgs (lbs)

W/P WHD

Nissan

Maxima A32, 4dr Sedan Feb 95-99 AU 75 kgs (165 lbs) 75 kgs (165 lbs)

Maxima, 4dr Sedan 95-99 ZA 75 kgs (165 lbs) 75 kgs (165 lbs)

Maxima, 4dr Sedan 95-99 EU 75 kgs (165 lbs) 75 kgs (165 lbs)

Maxima, 4dr Sedan Feb 95-99 NZ 75 kgs (165 lbs) 75 kgs (165 lbs)

Fitting Kit EN

K094

First Time Installation

●Remove parts from inside the package and

check. Contact your dealer if any parts are

missing or damaged.

●This kit fits type A, B, C and D.

●These instructions show type A crossbar

fitted. They also apply to type B, C and D.

NOTE: Clamp images in these instructions may

not be representative of the clamps in this kit

Fitting Kit EN

K094

●Use keys to remove covers.

●Use hex screwdriver to reverse adjusting

screw 10 turns.

●Press adjusting screw and pull crossbar

legs out. Refer to the crossbar instructions

for crossbar adjustment method.

●Ensure each end of the crossbar is

adjusted equally.

Fitting Kit EN

K094

●Remove locking screw.

●Cut protective strip in four equal lengths.

●Apply protective strip as shown.

Trim if required.

●Attach clamp to each leg. NOTE; clamps

may have labels showing their positions on

the vehicle (For example; "Front Right").

Fitting Kit EN

K094

●Refit locking screw so that it goes through

the hole in the clamp. Do not begin to

tighten the locking screw.

●Fit rubber pads (supplied with fitting kit) to

foot.

●Make sure the pad fits into the holes

underneath the foot.

Fitting Kit EN

K094

Fitment

●Place crossbar on vehicle. Minimum

recommended spacing between the bars is

700mm (27 1/2") (unless otherwise stated).

●Clamps over rubber door frame mouldings.

●Adjust the legs on the crossbar so that they

are positioned equally from the ends of the

crossbar, and the clamps engage firmly on

the body work of the vehicle.

●Tighten adjusting screw to 5 Nm (3.7 ft lb)

hand tight.

Fitting Kit EN

K094

●Tighten locking screw on both legs evenly.

●Check crossbar is securely attached to the

vehicle.

●Use keys to fit and lock covers

Fitting Kit EN

K094

CAUTION: Recheck all fasteners immediately after

a load is applied to the crossbars.

Regularly check screws are tight.

Fitting Kit EN

K094

Maintenance

●Clean the car roof and surfaces of the

product that will be in contact with the car

roof.

●Follow the fitting instructions for fitting the

product to your vehicle. Make sure all steps

are carried out in order.

●Set crossbars a minimum distance of

700mm (27 1/2") apart where no other

distance is specified in the fitting

instructions. This is especially important

when carrying long loads.

●Check unit is securely attached whenever

you refit it to the vehicle. If the unit feels

loose, refer to the fitting instructions and

readjust.

●Some glass/panoramic roofs and radio

antennae may not be able to be used when

the product is fitted.

●Do not modify this product.

●Refer to the maximum permitted load

capacity specified in the fitting instructions.

Do not exceed the vehicle manufacturers

roof load rating if it is lower than the

maximum load capacity specified in the

fitting instructions.

●Loads should not overhang the sides of the

product and be evenly distributed with the

lowest possible centre of gravity.

●Long loads should be secured with non-

elastic straps to the front and rear of the

vehicle.

●Objects with pointed ends (e.g. ski poles)

should be carried with the pointed ends to

the rear of the vehicle.

●Remove all loose or removable objects

from the load prior to loading.

●Make sure all loads are securely fastened

with non-elastic straps. Check regularly

during longer journeys.

●A loaded roof rack system can alter the

performance of your vehicle. Be especially

aware of the effects of side winds,

changing of direction, and braking

performance. Avoid rapid acceleration and

deceleration. Drive carefully.

●Note that the total height of the vehicle

increases when upright loads are carried.

●Products should be locked during transport

if they have locks fitted.

Inhaltsverzeichnis

Andere Prorack Autozubehör Handbücher

Prorack

Prorack K934 Bedienungs- und Installationshandbuch

Prorack

Prorack K877 Bedienungs- und Installationshandbuch

Prorack

Prorack K388 Bedienungsanleitung

Prorack

Prorack K404 Bedienungs- und Installationshandbuch

Prorack

Prorack K324 Bedienungsanleitung

Prorack

Prorack K1041 Bedienungsanleitung

Prorack

Prorack K449 Bedienungsanleitung

Prorack

Prorack K427 Bedienungsanleitung

Prorack

Prorack K1226 Bedienungsanleitung

Prorack

Prorack K188 Bedienungsanleitung

Prorack

Prorack VOYAGER PR3207 Bedienungsanleitung

Prorack

Prorack K769 Bedienungsanleitung

Prorack

Prorack K876 Bedienungsanleitung

Prorack

Prorack K156 Bedienungsanleitung

Prorack

Prorack K618 Bedienungsanleitung

Prorack

Prorack K363 Bedienungsanleitung

Prorack

Prorack K471W Bedienungsanleitung

Prorack

Prorack K762 Bedienungsanleitung

Prorack

Prorack K931 Bedienungsanleitung

Prorack

Prorack K766 Bedienungsanleitung

Prorack

Prorack K084 Bedienungsanleitung

Prorack

Prorack K540 Bedienungsanleitung

Prorack

Prorack K091 Bedienungsanleitung

Prorack

Prorack K070 Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung

Curt Manufacturing

Curt Manufacturing A25 Bedienungsanleitung