Prorack K919 Bedienungsanleitung
K919
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 1 x 6 x 4 x 2
x 6 x 1 x 6 x 1
Revision No: 3C 1
Fitting Kit K919
x 6 x 2 x 1 x 1
x 1 x 1
2
Fitting Kit K919
MAX kgs (lbs)
W/P WHD
Land Rover
Range Rover Sport (2 BAR), 5dr SUV 13-+ NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
Range Rover Sport (2 BAR), 5dr SUV 13-+ AU 75 kgs (165 lbs) 75 kgs (165 lbs)
Range Rover Sport (2 BAR), 5dr SUV 13-+ EU 75 kgs (165 lbs) 75 kgs (165 lbs)
Range Rover Sport (2 BAR), 5dr SUV 13-+ ZA 75 kgs (165 lbs) 75 kgs (165 lbs)
Range Rover Sport (2 BAR), 5dr SUV 13-+ CN 75 kgs (165 lbs) 75 kgs (165 lbs)
Range Rover Sport (3 BAR), 5dr SUV 13-+ AU 75 kgs (165 lbs) 75 kgs (165 lbs)
Range Rover Sport (3 BAR), 5dr SUV 13-+ CN 75 kgs (165 lbs) 75 kgs (165 lbs)
Range Rover Sport (3 BAR), 5dr SUV 13-+ EU 75 kgs (165 lbs) 75 kgs (165 lbs)
Range Rover Sport (3 BAR), 5dr SUV 13-+ NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
Range Rover Sport (3 BAR), 5dr SUV 13-+ ZA 75 kgs (165 lbs) 75 kgs (165 lbs)
3
Fitting Kit K919
X
A B C 1 2 3
Range Rover Sport (2 BAR), 5dr SUV 13-+ (NZ) -230mm 450mm - 1056mm 1056mm -
-9 -1/16ths" 17 3/4ths" - 41 9/16ths" 41 9/16ths" -
Range Rover Sport (2 BAR), 5dr SUV 13-+ (AU) -230mm 450mm - 1056mm 1056mm -
-9 -1/16ths" 17 3/4ths" - 41 9/16ths" 41 9/16ths" -
Range Rover Sport (2 BAR), 5dr SUV 13-+ (EU) -230mm 450mm - 1056mm 1056mm -
-9 -1/16ths" 17 3/4ths" - 41 9/16ths" 41 9/16ths" -
Range Rover Sport (2 BAR), 5dr SUV 13-+ (ZA) -230mm 450mm - 1056mm 1056mm -
-9 -1/16ths" 17 3/4ths" - 41 9/16ths" 41 9/16ths" -
Range Rover Sport (2 BAR), 5dr SUV 13-+ (CN) -230mm 450mm - 1056mm 1056mm -
-9 -1/16ths" 17 3/4ths" - 41 9/16ths" 41 9/16ths" -
Range Rover Sport (3 BAR), 5dr SUV 13-+ (AU) -230mm 450mm 1285mm 1056mm 1056mm 1028mm
-9 -1/16ths" 17 3/4ths" 50 9/16ths" 41 9/16ths" 41 9/16ths" 40 1/2ths"
Range Rover Sport (3 BAR), 5dr SUV 13-+ (CN) -230mm 450mm 1285mm 1056mm 1056mm 1028mm
-9 -1/16ths" 17 3/4ths" 50 9/16ths" 41 9/16ths" 41 9/16ths" 40 1/2ths"
Range Rover Sport (3 BAR), 5dr SUV 13-+ (EU) -230mm 450mm 1285mm 1056mm 1056mm 1028mm
-9 -1/16ths" 17 3/4ths" 50 9/16ths" 41 9/16ths" 41 9/16ths" 40 1/2ths"
Range Rover Sport (3 BAR), 5dr SUV 13-+ (NZ) -230mm 450mm 1285mm 1056mm 1056mm 1028mm
-9 -1/16ths" 17 3/4ths" 50 9/16ths" 41 9/16ths" 41 9/16ths" 40 1/2ths"
Range Rover Sport (3 BAR), 5dr SUV 13-+ (ZA) -230mm 450mm 1285mm 1056mm 1056mm 1028mm
-9 -1/16ths" 17 3/4ths" 50 9/16ths" 41 9/16ths" 41 9/16ths" 40 1/2ths"
4
Fitting Kit EN
K919
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
●Use keys to remove covers.
5
Fitting Kit EN
K919
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
●Attaches to factory-fitted mounting points
●Please check the front of this manual for
information relating specifically to your
vehicle.
●Adjust crossbar in or out to suit vehicle.
Refer to the crossbar instructions for
crossbar adjustment.
6
Fitting Kit EN
K919
●Tighten adjusting screw to 2 Nm (1.5 ft lb)
hand tight.
●Remove plastic clamp block by gripping bar
leg with fingers and push firmly with
thumbs until clamp block drops out behind
leg.
●Select plastic internal block (from fitting kit)
and insert into foot.
●Repeat for all legs.
7
Fitting Kit EN
K919
Fitment
●Lift and pull ditch moulding back towards
you and remove from the vehicle.
●Remove retaining clips from 2nd and 4th
position for 2 bar system.
●Remove retaining clips from 2nd, 4th and
6th position for 3 bar system.
●Repeat both sides.
●Remove centre of retaining clip by twisting.
●Repeat for all six positions.
8
Fitting Kit EN
K919
●Use drill bit supplied, to drill holes in
marked positions on ditch mould.
●Replace retaining clips into ditch mould.
●Re-install rubber ditch mould back into roof
channel and click into place.
9
Fitting Kit EN
K919
●Letters refer to the part numbers stamped
on clamps.
●Grubscrew Part Number: 2 bars only
A = 70mm
●Grubscrew Part Number: 3 bars only
A = 70mm
B = 90mm
●Select grubscrews and screw into the
vehicle's fixed points.
●Do not over tighten.
●Repeat for all positions.
●Refer to the underside of the pad for the
part number.
10
Inhaltsverzeichnis
Andere Prorack Autozubehör Handbücher
Prorack
Prorack K457 Bedienungs- und Installationshandbuch
Prorack
Prorack K730 Bedienungsanleitung
Prorack
Prorack VOYAGER PR3207 Bedienungsanleitung
Prorack
Prorack K199 Bedienungsanleitung
Prorack
Prorack K594 Bedienungsanleitung
Prorack
Prorack K621 Bedienungsanleitung
Prorack
Prorack K868 Bedienungsanleitung
Prorack
Prorack K192 Bedienungsanleitung
Prorack
Prorack K869 Bedienungsanleitung
Prorack
Prorack K402 Bedienungsanleitung
Prorack
Prorack K078 Bedienungsanleitung
Prorack
Prorack K473 Bedienungsanleitung
Prorack
Prorack K416 Bedienungs- und Installationshandbuch
Prorack
Prorack S16 Bedienungsanleitung
Prorack
Prorack K122 Bedienungsanleitung
Prorack
Prorack K661 Bedienungs- und Installationshandbuch
Prorack
Prorack PR3097 Bedienungsanleitung
Prorack
Prorack K412 Bedienungsanleitung
Prorack
Prorack K1242 Bedienungsanleitung
Prorack
Prorack K698 Bedienungs- und Installationshandbuch
