PSC SP400rf Betriebsanleitung

ROGRAMMING

UIDE

ADIO

REQUENCY

ANDHELD

ASER

CANNER

PSC Scanning, Inc.

959 Terry Street

Eugene, Oregon 97402

Telephone: (541) 683-5700

Toll Free: (800) 547-2507

Telefax: (541) 345-7140

PSC and the PSC logo are registered trademarks of PSC INC

This manual and the procedures described in it are copyrighted, with all rights

reserved. Under copyright law, this manual may not be copied in whole or in part

without the prior written consent of PSC. The same proprietary and copyright notices

must appear on any permitted copies as appears on the original. This exception does

not permit copies to be made for others, whether or not sold. Under the law, copying

includes translating into another language or format.

Disclaimer

Reasonable measures have been taken to ensure that the information included

in this manual is complete and accurate. However, PSC reserves the right to

change any specification at any time without prior notice.

R44-1027 i

Contents

Introduction

I Need to Understand the Basics.............................. 1

Integrating Peripherals With Host Systems ............. 1

Changing Interfaces................................................. 2

Customizing Your Scanner Operation ...................... 3

Programming Overview ................................................. 4

What Is Programming Mode? ................................. 4

How To Program Using Barcodes............................ 4

The Programming Session ...................................... 5

Scanner Response When In Programming Mode .... 5

If You Make a Mistake... .......................................... 6

Return to Factory Settings ....................................... 6

Configuration Upload............................................... 6

Where To Go From Here .......................................... 7

Interface Selection

IBMIBM 4683/84 • 4693/94 Port 5B I/F Selection .......... 8

IBM 4683/84 • 4693/94 Port 9A, 9B,

9C, 9E I/F Selection.......................................... 9

IBM 4682/92 Port E Interface Selection................. 10

OCIA

PSC OCIA Interface Selection ................................ 11

NCR OCIA Eight Bit (short format) I/F Selection .... 11

NCR OCIA Nine Bit (long format) I/F Selection ...... 11

SNI OCIA Interface Selection ................................. 11

OCIA Options ......................................................... 12

Wand

Wand Emulation Interface Selection ...................... 13

SP400RF

Programming Guide

RS-232

RS-232 Interface Selection .................................... 15

SNI RS-232 Interface Selection ............................. 15

Hardware Control................................................... 18

Software Control.................................................... 19

Keyboard Wedge

PC Keyboard Wedge Interface Selection................ 22

PC Keyboard Wedge –

Connect to a Laptop/No Keyboard Attached ...... 23

STI Keyboard Wedge Interface Selection ............... 26

Label Transmit Format Configuration Items ................ 27

Prefix & Suffix ....................................................... 27

ASCII Character Set ............................................... 33

Symbologies

Symbology Options Overview...................................... 42

Symbology Selection ................................................... 43

UPC/EAN Options ........................................................ 45

UPC/EAN Expansion .............................................. 46

UPC/EAN Add-Ons................................................. 47

Price/Weight Check Digit ....................................... 50

Code 39 Options .......................................................... 51

Interleaved 2 of 5......................................................... 55

Check Digit and Variable Length Label Selections . 56

Standard 2 of 5 ............................................................ 60

Normal or IATA Selection ...................................... 61

Check Digit and Variable Length Label Selections . 62

Codabar Options .......................................................... 65

Codabar Check Digit & Variable Length ................. 66

Codabar Start/Stop Character ................................ 67

Codabar Fixed Length ............................................ 68

MSI/Plessey Options ................................................... 70

MSI/Plessey Check Digit........................................ 70

MSI/Plessey Fixed Length...................................... 71

R44-1027 iii

Code 128 Options ........................................................ 73

AIM Symbology ID Prefix ...................................... 73

General Features .......................................................... 74

Communications Protocol ..................................... 75

ASCII Character Set ............................................... 78

When To Acknowledge .......................................... 80

“When to Beep” Options ........................................ 84

Beeper Volume ...................................................... 88

Radio Channel Frequency ...................................... 89

Radio Transmit Power ........................................... 90

Wait Time For Host Acknowledge .......................... 91

Read Verification ................................................... 93

Low Battery Indication Method .............................. 95

Appendix A

Standard Factory Settings............................................ 96

Factory Defaults..................................................... 96

Interface-Discrete Defaults .......................................... 99

RS-232/Keyboard Wedge ...................................... 99

IBM Interfaces ..................................................... 100

Appendix B

Additional Information ............................................... 101

Host Programming .................................................... 101

Creating MultiFunction Labels ................................... 101

Need More Information.............................................. 101

Appendix C

Sample Barcodes....................................................... 102

NOTES

SP400RF

Programming Guide

R44-1027 1

GENERAL

INFORMATION

INTRODUCTION

This manual contains instructions for changing interfaces, barcodes for

customizing the

SP400RF

scanner's operation and a listing of standard

factory settings. It is important to note that many of the features and

programming labels contained here are identical to those available for

other

SP400

models. Since the

SP400RF

contains software enhance-

ments and characteristics that set it apart from other models, it is recom-

mended that this guide be used as the sole source of programming labels

and information (except for other

SP400RF

product-specific publica-

tions).

The organization of this manual is intended to support a variety of users

while making it quick and easy to find the information you need. Look at

the descriptions that follow to find where to go from here.

I NEED TO UNDERSTAND THE BASICS

If you do not regularly use barcode labels to configure (program) scan-

ners, it will be very helpful to read the introductory portions of this

manual prior to beginning your programming session. In addition to the

information that follows, information of specific interest to you is titled:

— Integrating Peripherals with Host Systems

— Changing Interfaces

— Customizing Your Scanner Operation

— Programming Overview

— What is Programming Mode?

— How to Program Using Barcodes

— The Programming Session

— Scanner Response When in Programming Mode

— If You Make A Mistake

— Where to Go From Here

INTEGRATING PERIPHERALS WITH HOST SYSTEMS

It is important that you understand that the scanner must contain software

that supports a specific interface in order to use that interface.

Next, turn to Appendix A, Standard Factory Settings, which contains a

complete factory default configuration listing. Assuming that your scanner

is configured using the standard factory settings, use this list to identify

any changes or additions you need to make.

Then, locate the programming labels you need and change the necessary

settings. Once you have completed these steps, you can begin scanning.

SP400RF

Programming Guide

GENERAL

INFORMATION

CHANGING INTERFACES

The scanner is configured at the factory to support one of two interface

groups listed in Table 1 below. Changing the current interface is simply a

matter of selecting the desired interface from your scanner's group, and

enabling the new interface using the programming labels contained in this guide.

Table 1. SP400RF Interface Groups

S-232 • IBM • OCIA Group RS-232 • Wand Emulation • Keyboard Wedge Group

RS-232 RS-232

SNI RS-232 SNI RS-232

IBM 468x/9x Port 5B

Wand Emulation

IBM 468x/9x Port 9x

Type A — PC/XT w/foreign keyboard

IBM 4682/92 Port E

Type B — AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95

w/foreign keyboard

PSC

OCIA

Type C — PS/2 25 and 30 w/foreign keyboard

NCR OCIAEightBit

Type D — PC/XT w/USkeyboard

NCR OCIANineBit

Type E — AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95

w/USkeyboard

SNI OCIA

Type F— PS/2 25 and 30 w/USkeyboard

STI keyboard wedge

NOTE

If you attempt to select an interface that is

not supported by your scanner, or if the

scanner's interface hardware malfunctions,

all three LEDs will flash five times and the

scanner will automatically reset to the stan-

dard RS-232 interface. The scanner will oth-

erwise be returned to normal function.

Once you have enabled the new interface with the appropriate label, the

new interface becomes the default interface that is active whenever power

is applied to the scanner.

The following steps describe the interface change procedure.

1. Turn to the appropriate page in this manual and scan the

desired interface enable programming label. This will enable

the software for the new interface and disable the 'old'

interface software.

2. Scan a barcode to verify that the scanner communicates

correctly with the host system. Some sample barcodes are

provided on the last pages of this manual. If any changes to

the scanner's factory settings are needed, use the instructions

titled, Customizing Your Scanner Operation.

1 Formerly titled: "Spectra-Physics OCIA" or "S-P OCIA".

R44-1027 3

GENERAL

INFORMATION

CUSTOMIZING YOUR SCANNER OPERATION

When enabling a new interface, it may be necessary to modify the stan-

dard factory settings to match your specific host system's communication

and symbology requirements. Check with your system administrator to

identify your host system's specific interface requirements to ensure that

they match the new interface you have selected. Also, the scanner's

operational features (e.g. speaker volume, radio channel frequency, etc.)

can be customized to match your unique requirements.

1. Use the labels in this manual to modify the standard configu-

ration to match your specific interface requirements or user

preference.

NOTE

Ensure that your planned modifications are

compatible with the current interface. For

example, baud rate selections are only valid in

the RS-232 interface. The scanner will read

and seem to accept programming labels for

features invalid to the current interface, how-

ever the feature will not be modified.

2. Enable any additional symbologies as required and exit

Programming Mode.

3. Scan a regular barcode label and verify that the scanner and

host communicate correctly.

4. You have completed the factory settings change procedure.

If you experience difficulties, have questions or require additional infor-

mation, contact your local distributor using the listings located on the back

cover of this guide.

SP400RF

Programming Guide

GENERAL

INFORMATION

PROGRAMMING OVERVIEW

This section describes how to set the scanner's programmable features.

These features can be configured using the barcode labels contained in

this manual or by using commands sent from the host. Refer to Appendix

B, Additional Information, for host programming details. If you program

the scanner using these barcodes, the scanner stores the changes until

reprogrammed. Whenever you use these labels to change programmable

features, you are changing these features for the active interface only.

WHAT ISPROGRAMMING MODE?

To change the scanner's programmed settings, it is necessary to place the

scanner in Programming Mode using the special “set” label. This ensures

that the scanner only recognizes the special programming labels contained

in this programming guide.

HOW TOPROGRAM USING BARCODES

The following pages contain special barcode labels that are used to

change or enable the scanner's programmable options. All programming

sessions follow this order, unless otherwise instructed:

NOTE

Programming should be performed with the

base station in near proximity to ensure opti-

mal communication and sllow the user to

monitor the base station’s LED indicators.

1. Scan the SET label at the top of the page. The scanner will

emit two beeps indicating it has read the label, and the base

station’s red LED will begin flashing. As long as the lamp is

flashing, the scanner will only recognize and decode pro-

gramming labels.

2. Scan the feature label(s) for the programmable options

you wish to enable. The scanner will emit two beeps each

time you scan a valid label. (Note that not all features are

available for all interfaces.) The first beep indicates that the

scanner has read the label, the second announces base station

acknowledgement of the label.

3. Scan the END label at the bottom of the page to complete

the programming session and exit Programming Mode.

Inhaltsverzeichnis

Andere PSC Barcode-Lesegerät Handbücher

PSC

PSC SP400 Betriebsanleitung

PSC

PSC vs1200 Bedienungsanleitung

PSC

PSC QRG QuickScan QS3500 Bedienungsanleitung

PSC

PSC Magellan 2200VS omega Bedienungsanleitung

PSC

PSC QuickScan QS6500 Bedienungsanleitung

PSC

PSC QuickScan QS2500 Installations- und Betriebshandbuch

PSC

PSC Magellan 2300HS Bedienungsanleitung

PSC

PSC Scanners Betriebsanleitung

PSC

PSC Magellan 2200VS omega Bedienungsanleitung

PSC

PSC Magellan 8500 Bedienungsanleitung

PSC

PSC PowerScanTM RF Bedienungsanleitung

PSC

PSC HS1250, Bedienungsanleitung

PSC

PSC PowerScan RF Benutzerhandbuch

PSC

PSC QuickScan QS2500 Installations- und Betriebshandbuch

PSC

PSC PowerScan RF Bedienungsanleitung

PSC

PSC Duet Bedienungsanleitung

PSC

PSC QuickScan 6000 Betriebsanleitung

PSC

PSC PSRF-1000 Benutzerhandbuch

PSC

PSC HD Bedienungsanleitung

PSC

PSC LM520 Betriebsanleitung

PSC

PSC PowerScan Betriebsanleitung

PSC

PSC QuickScan QS6500 Bedienungsanleitung

PSC

PSC QuickScan QS2500 Bedienungsanleitung

PSC

PSC LazerData Series 9000E Bedienungsanleitung

Beliebte Barcode-Lesegerät Handbücher anderer Marken

POSMicro

POSMicro Datalogic PowerScan D7100 Bedienungsanleitung

Marson

Marson MT780 Kurzanleitung zur Einrichtung

NCR

NCR RealPOS Bedienungsanleitung

Motorola

Motorola SE3300 Kurzanleitung zur Einrichtung

Element

Element P130BT Bedienungsanleitung

Motorola

Motorola Symbol LS3008 Installations- und Betriebshandbuch

Meec tools

Meec tools OBD-II / VAG Bedienungsanleitung

SICK

SICK CLP 100 Bedienungsanleitung

Royal Tag SA

Royal Tag SA I-Read Bedienungsanleitung

Welch Allyn

Welch Allyn IMAGETEAM 3800 Bedienungsanleitung

Meteor

Meteor 8310 Bedienungsanleitung

Denso

Denso BHT-500B Bedienungsanleitung

Datalogic

Datalogic Heron HD3130 Bedienungsanleitung

Motorola

Motorola MP6000 Montageanleitung

Newland

Newland NLS-HR15-BT Bedienungsanleitung

ARTDEV

ARTDEV AS-1310 Bedienungsanleitung

Aopos

Aopos AS290 Bedienungsanleitung

ENS

ENS 367-5455 Bedienungsanleitung