Quadra-Fire 31I-ACC Bedienungsanleitung

1 7044-225B April 9, 2014

3100-I ACC WOOD INSERT

Automatic Combustion Control (ACC)

Model(s):

31-I ACC

O-T L

Tested and

Listed by

Portland

Oregon USA

OMNI-Test Laboratories, Inc.

CUS

HOT SURFACES!

Glass and other surfaces are hot

during operation AND cool down.

Hot glass will cause burns.

• Do not touch glass until it is cooled

• NEVER allow children to touch glass

• Keep children away

• CAREFULLY SUPERVISE children in same room as

replace.

• Alert children and adults to hazards of high temperatures

• High temperatures may ignite clothing or other

ammablematerials.

• Keepclothing,furniture,draperiesandotherammable

materials away.

WARNING

If the information in these instruc-

tions is not followed exactly, a

remayresultcausingproperty

damage, personal injury, or death.

• Donotstoreorusegasolineorotheram-

mablevaporsandliquidsinthevicinityof

this or any other appliance.

• Donotoverre-Ifheaterorchimneycon-

nectorglows,youareoverring.Overring

willvoidyourwarranty.

• Complywithallminimumclearancesto

combustiblesasspecied.Failureto

complymaycausehousere.

WARNING

Fire Risk.

For use with solid wood fuel only.

Otherfuelsmayoverreandgenerate

poisonousgases(i.e.carbonmonoxide).

Installationandserviceofthisapplianceshould

beperformedbyqualiedpersonnel.Hearth&

HomeTechnologiesrecommendsNFIcertied

professionals,ortechnicianssupervisedbyan

NFIcertiedprofessional.

WARNING

Installation Manual

Installation & Appliance Set-Up

INSTALLER: Leave this manual with party responsible for use and operation.

OWNER: Retain this manual for future reference.

NOTICE: DO NOT DISCARD THIS MANUAL

NOTE

ToobtainaFrenchtranslationofthismanual,pleasecontact

yourdealerorvisitwww.quadrare.com

Pourobtenirunetraductionfrançaisedecemanuel,s’ilvous

plaîtcontactervotrerevendeurouvisitezwww.quadrare.com

2 7044-225B April 9, 2014

31-I ACC

1 Important Safety Information

A.InsertCertication.............................................................3

B.BTU&EfciencySpecications........................................3

C.MobileHomeApproved .................................................... 3

D.GlassSpecications .........................................................3

E.Non-CombustibleMaterials ...............................................3

F.CombustibleMaterials........................................................3

2 Getting Started

. Design and Installation Considerations ..................................4

B. Draft ..............................................................................4

C.NegativePressure............................................................5

D.ToolsAndSuppliesNeeded..............................................5

E. Inspect Appliance and Components ..................................5

F. Install Checklist ..................................................................6

3 Dimensions and Clearances

A. Appliance Dimensions ......................................................7

B.ClearancestoCombustibles..............................................8

C. Calculating Alternate Floor Protection ..............................9

D.LocatingYourStove&Chimney .......................................10

E.ChimneyTerminationRequirements.................................10

F. 2-10-3 Rule .......................................................................11

4 Chimney Systems

A. Venting Systems ...............................................................12

B. Inspections........................................................................12

C. Larger Chimneys ..............................................................12

D. Masonry Chimney.............................................................12

E.MetalHeatCirculatingMasonry........................................14

F.PrefabricatedMetalChimney ............................................14

G. Securing Chimney Components.......................................15

H.AlteringtheFireplace........................................................15

I. Zero-Clearance Fireplace ..................................................16

J.OvalizingRoundStainlessSteelLiners ............................16

K.ChimneyHeight/RiseandRun .......................................16

5 Appliance Set-Up

A.OutsideAirKitInstallation..................................................17

B.DisassembleFireboxandOuterCan................................18

C.SecuringStovePipe/LinertoFlueCollar..........................19

D.OptionalOffsetAdapterInstallation ..................................19

E.InstallingOuterCan&LevelingBolts ...............................20

F.Surround&TrimKitInstallation.........................................20

G.InstallingFireboxintoOuterCan......................................21

H.SecuringAppliancetoStovePipe/Liner ...........................21

I.LevelingLegs....................................................................21

J. Snap Disc and Side Panel Installation ..............................22

K. Blower Installation.............................................................22

L. Blower Cord Installation on Left Side................................23

M.ZeroClearanceAdjustableTrimSupport,2”to10”.........24

6 Mobile Home Installation

7 Accessory List

TABLE OF CONTENTS

Safety Alert Key:

• DANGER! Indicatesahazardoussituationwhich,ifnotavoidedwill result in death or serious injury.

• WARNING!Indicatesahazardoussituationwhich,ifnotavoidedmay result in death or serious injury.

• CAUTION! Indicatesahazardoussituationwhich,ifnotavoided,may result in minor or moderate injury.

• NOTICE: Indicates practices which may cause damage to the appliance or to property.

April 9, 2014 7044-225B 3

31-I ACC

Model: 3100-I(ACC)Insert

Laboratory: OMNITestLaboratories,Inc.

Report No: 061-S-74-6.2

Type: SolidFuelType,ListedRoomHeater

Standard: UL1482 and ULC S628-93 and

(UM)84-HUD,MobileHome

Approved.

EPACertied: 2.0 grams per hour

Efciency: up to 79.8%

EPA BTU Output: 11,800 to 32,000

Heating Capacity: upto1800sqftdepending

on climate zone

Vent Size: 6 inches

Firebox Size: 1.9cubicfeet

Max Wood Length: 18 inches

Max First Hour BTUs: 57,100 @ 75.3% B415

TestedEfcienty

Fuel: Cord Wood

Shipping Weight: 345lbs

TheQuadra-Fire3100WoodInsert(ACC)meetstheU.S.Environ-

mentalProtectionAgency’s1990particulateemissionstandards.

1 Important Safety Information

A.InsertCertication

NOTE:Hearth&HomeTechnologies,manufacturerof

thisappliance,reservestherighttoalteritsproducts,their

specicationsand/orpricewithoutnotice.

NOTE:Thisinstallationmustconformwithlocalcodes.Inthe

absenceoflocalcodesyoumustcomplywiththeUL1482,(UM)

84-HUDandNPFA211intheU.S.A.andtheULCS628-93and

CAN/CSA-B365InstallationCodesinCanada.

C. Mobile Home Approved

 • Thisapplianceisapprovedformobilehomeinstalla-

tions when not installed in a sleeping room and when

anoutsidecombustionairinletisprovided.

 • Thestructuralintegrityofthemobilehomeoor,ceil-

ing,andwallsmustbemaintained.

 • Theappliancemustbeproperlygroundedtotheframe

ofthemobilehomewith#8coppergroundwire,and

chimneymustbelistedtoUL103 HToralistedUL-

1777fulllengthsixinch(152mm)diameterlinermust

beused.

 • OutsideAirKit,partOAK-ACCmustbeinstalledina

mobilehomeinstallation.

Improper installation, adjustment, alteration, service or

maintenance can cause injury or property damage.

Forassistanceoradditionalinformation,consultaqualied

installer,serviceagencyoryourdealer.

Quadra-FireisaregisteredtrademarkofHearth&Home

Technologies.

• Installationanduseofanydamagedappliance.

• Modicationoftheappliance.

• Installation other than as instructed by Hearth & Home

Technologies.

• Installationand/oruseofanycomponentpartnotapprovedby

Hearth&HomeTechnologies.

• Operatingappliancewithoutfullyassemblingallcomponents.

• Operatingappliancewithoutlegsattached(ifsuppliedwithunit).

• DoNOTOverre-Ifapplianceorchimneyconnectorglows,you

areoverring.

Anysuchactionthatmaycausearehazard.

WARNING

Fire Risk.

Hearth&HomeTechnologiesdisclaimsany

responsibilityfor,andthewarrantywillbevoided

by,thefollowingactions:

B.BTU&EfciencySpecications

D.GlassSpecications

Thisstoveisequippedwith5mmceramicglass.Replace

glass only with 5mm ceramic glass. Please contact your

dealer for replacement glass.

Hearth&HomeTechnologiesWILLNOTwarrantystoves

thatexhibitevidenceofover-ring.Evidenceofover-ring

includes,butisnotlimitedto:

 • Warpedairtube

 • Deterioratedrefractorybrickretainers

 • Deterioratedbafeandotherinteriorcomponents

E. Non-Combustible Materials

Materialwhichwillnotigniteandburn,composedofany

combinationofthefollowing:

- Steel - Plaster

- Brick - Iron

 -Concrete  -Tile

- Glass - Slate

Materials reported as passing ASTM E 136, Standard

Test Method for Behavior of Metals, in a Vertical Tube

Furnace of 750° C.

F. Combustible Materials

Materialmadeof/orsurfacedwithanyofthefollowingma-

terials:

- Wood - Compressed Paper

 -PlantFibers  -Plastic

 -Plywood/OSB  -SheetRock(drywall)

Anymaterialthatcanigniteandburn:ameproofedornot,

plastered or un-plastered.

4 7044-225B April 9, 2014

31-I ACC

Install Guide

2 Getting Started

. Design and Installation Considerations

Beforeinstalling,determinethefollowing:

• Typeofchimneyconnectortobeused

· singlewall,6inch(152mm)diameter,stainlesssteel,or

·doublewall,6inch(152mm)diameter,stainlesssteel

• Consultpage28forclearancestocombustibles

• Poweroutletlocatedclosebyforoptionalblower

Draftisthepressuredifferenceneededtoventappliances

successfully. When a appliance is drafting successfully, all

combustion byproducts are exiting the home through the

chimney.

Considerationsforsuccessfuldraftinclude:

• Preventingnegativepressure

• Locationofapplianceandchimney

obesurethatyourapplianceburnsproperly:

• Duringalowburn,thechimneydraft(staticpressure)should

beapproximately-.04inchwatercolumn(W.C.)

• Duringahighburnthechimneydraftshouldbeapproximately

-.10inch(W.C.)

• MeasuretheW.Cat6inches(152mm)abovethetopofthe

applianceafteronehourofoperationateachburnsetting.

B. Draft

Checkbuildingcodespriortoinstallation.

• Installation MUST comply with local, regional, state and

national codes and regulations.

• Consult insurance carrier, local building, re ofcials or

authoritieshavingjurisdictionaboutrestrictions,installation

inspection, and permits.

CAUTION

WARNING

• DONOTCONNECTTHISUNITTOACHIMNEY

FLUESERVICINGANOTHERAPPLIANCE.

• DONOTCONNECTTOANYAIRDISTRIBUTION

DUCTORSYSTEM.

Mayallowuegasestoenterthehouse.

Asphyxiation Risk.

• Installationanduseofanydamagedappliance.

• Modicationoftheappliance.

• Installation other than as instructed by Hearth & Home

Technologies.

• Installationand/oruseofanycomponentpartnotapproved

byHearth&HomeTechnologies.

• Operatingappliancewithoutfullyassemblingallcomponents.

• Operatingappliancewithoutlegsattached(ifsuppliedwith

unit).

• DoNOTOverre-Ifapplianceorchimneyconnectorglows,

youareoverring.

Anysuchactionthatmaycausearehazard.

WARNING

Fire Risk.

Hearth&HomeTechnologiesdisclaimsany

responsibilityfor,andthewarrantywillbe

voidedby,thefollowingactions:

NOTICE: Hearth & Home Technologies assumes no

responsibility for the improper performance of the

appliancesystemcausedby:

• Inadequatedraftduetoenvironmentalconditions

• Downdrafts

• Tightsealingconstructionofthestructure

• Mechanicalexhaustingdevices

• Overdraftingcausedbyexcessivechimneyheights

• Idealperformanceiswithheightofchimneybetween

14-16feet(4.26-4.88m)measuredfromthebaseof

the appliance.

April 9, 2014 7044-225B 5

31-I ACC

C. Negative Pressure

Negative pressure results from the imbalance of air avail-

ablefortheappliancetooperateproperly. Itcanbestron-

gestinlowerlevelsofthehouse.

Causesinclude:

• Exhaustfans(kitchen,bath,etc.)

• Rangehoods

• Combustionairrequirementsforfurnaces,waterheaters

andothercombustionappliances

• Clothesdryers

• Locationofreturn-airventstofurnaceorairconditioning

• ImbalancesoftheHVACairhandlingsystem

• Upperlevelairleakssuchas:

- Recessed lighting

- Attic hatch

- Duct leaks

Tominimizetheeffectsofnegativeairpressure:

• Installtheoutsideairkitwiththeintakefacingprevailing

winds during the heating season

• Ensureadequateoutdoorairforallcombustionappliances

andexhaustequipment

• Ensurefurnaceandairconditioningreturnventsarenot

locatedintheimmediatevicinityoftheappliance

• Avoid installing the appliance near doors, walkways or

small isolated spaces

• Recessedlightingshouldbea“sealedcan”design

• Attichatchesweatherstrippedorsealed

• Atticmountedductworkandairhandlerjointsandseams

taped or sealed

• Basementinstallationsshouldbeavoided

WARNING

• Negativepressurecancausespillageofcom-

bustionfumes,sootandcarbonmonoxide.

• Applianceneedstodraftproperlyforsafety.

Asphyxiation Risk.

D. Tools And Supplies Needed

Beforebeginningtheinstallationbesurethefollowingtools

andbuildingsuppliesareavailable:

Reciprocating saw Framing material

Pliers Hightempcaulkingmaterial

Hammer Gloves

Phillipsscrewdriver Framingsquare

Flatbladescrewdriver Electricdrillandbits

Plumbline Safetyglasses

Level Tapemeasure

1/2-3/4in.length,#6or#8self-drillingscrews

Misc. screws and nails

• Removeapplianceandcomponentsfrompackagingand

inspect for damage.

• Vent system components and doors are shipped in

separate packages.

• Reporttoyourdealeranypartsdamagedinshipment.

• Read all the instructions before starting the

installation. Follow these instructions carefully during

theinstallationtoensuremaximumsafetyandbenet.

E. Inspect Appliance and Components

Inspect appliance and components for damage.

Damaged parts may impair safe operation.

WARNING

• DoNOTinstalldamagedcomponents.

• DoNOTinstallincompletecomponents.

• DoNOTinstallsubstitutecomponents.

Report damaged parts to dealer.

Fire Risk.

6 7044-225B April 9, 2014

31-I ACC

ATTENTION INSTALLER:

Follow this Standard Work Checklist

Thisstandardworkchecklististobeusedbytheinstallerinconjunctionwith,notinsteadof,theinstructionscontainedinthisinstallationmanual.

Customer:

Date Installed:

Lot/Address:

Location of Fireplace:

Installer:

Dealer/ Distributor Phone #:

Serial #:

Model (circle one): 31I-ACC

WARNING! Risk of Fire or Explosion! Failuretoinstallreplaceaccordingtotheseinstructionscanleadtoareorexplosion.

Appliance Install

Veriedclearancestocombustibles.(Pg.8)

Fireplaceisleveledandlinerissecuredtoappliance.(Pg.18)

Hearthextensionsize/heightdecided.(Pg.22)

Outsideairkitinstalled.(Pg.16)

Floorprotectionrequirementshavebeenmet.

Themasonrychimneyisinspectedbyaprofessionalandiscleanorthe

factorybuiltmetalchimneyisinstalledaccordingtothemanufacturer’s

instructions and clearances.

Chimney Section 4 (Pg. 11)

Chimneycongurationcomplieswithdiagrams.

Chimney installed, locked and secured in place with proper clearance.

Chimneymeetstheminimumheightrequirements.

Roofashinginstalledandsealed.

Terminationsinstalledandsealed.

Clearances Section 3 (Pg. 7)

Combustiblematerialsnotinstalledinnon-combustibleareas.

Veriedallclearancesmeetinstallationmanualrequirements.

Mantelsandwallprojectionscomplywithinstallationmanualrequirements.

Protectivehearthstripsandhearthextensioninstalledpermanualrequirements.

Appliance Setup Section 5 (Pg. 16)

Allpackagingandprotectivematerialsremoved.

Firebrick,bafeandceramicblanketinstalledcorrectly.

Alllabelshavebeenremovedfromthedoor.

Allpackagingmaterialsareremovedfrominside/underthereplace.

Manualbagandallofitscontentsareremovedfrominside/underthereplace

andgiventothepartyresponsibleforuseandoperation.

Hearth & Home Technologies recommends the following:

•Photographingtheinstallationandcopyingthischecklistforyourle.

•Thatthischecklistremainvisibleatalltimesonthereplaceuntiltheinstallationiscomplete.

Comments: Furtherdescriptionoftheissues,whoisresponsible(Installer/Builder/OtherTrades,etc.)andcorrectiveactionneeded:

Commentscommunicatedtopartyresponsible by on

(Builder/Gen.Contractor) (Installer)(Date)

Part#4017-254•RevB•01/29/13

YES IF NO, WHY?

F. Install Checklist

April 9, 2014 7044-225B 7

31-I ACC

Figure 7.1 Top View Figure 7.2 Front View

Figure 7.3 - Side View

27-5/8 in (702mm)

23-13/16 in (589mm)

38-9/16 in (979mm)

5-1/2 in (140mm)

5-11/16 in (144mm)

8-1/2 in (216mm)

7-3/4 in (197mm)

12-1/2 in

(318mm)

26-3/4 in (679mm)

23-1/4 in (591mm)

14-1/4 in

(362mm)

20-7/16 in

(519mm)

21-1/2 in

(546mm)

Surround Sizes AB

Standard 43in.(1092mm) 31in.(787mm)

Large 53in.(1346mm) 34in.(864mm)

11-7/8 in. to 15-3/16 in.

(302mm to 386mm)

4 in.

(102mm)

24-3/16 in.

(614mm)

16-5/16 in. to 19-5/8 in.

(414mm to 498mm)

Figure 7.4 - Side View With Optional Offset Adapter

3 Dimensions and Clearances

A. Appliance Dimensions NOTE:FlueCollarsizeis6inch(152mm)diameter(ID)

8 7044-225B April 9, 2014

31-I ACC

NOTE: Clearances may only be reduced by

means approved by the regulatory authority

having jurisdiction

Fire Risk.

• Complywithallminimumclearancesto

combustiblesasspecied.

• Failuretocomplymaycausehousere.

WARNING

InCanadaafulllength6inch(152mm)S635uelinerrequiredasperULCS628.

InUSAaminimum5ftlength(1.82m),6inch(152mm)diameteruelinerisrequiredasperUL1482.

SIDE TRIM

SIDE WALL

TOP TRIM

27-1/4

692mm

32-1/4

819mm

HEARTH

EXTENSION

USA 16-3/4

CANADA

24-3/4 (629mm)

40-11/16

1033mm

FIREPLACE FRONT SURFACE

USA 23-1/2

CANADA 25-1/2 (648mm)

HEARTH EXTENSION

51 7/16

1306mm

12in max

MANTEL

See next page for thermal protection

calculations

THERMAL

PROTECTION

USA

& CANADA

Floorheight0”to6-1/2”

(6mmto165mm)below

insertbase

1-1/2inch(38)of

k=3.06

Floor height greater

than6-1/2”(165mm)

belowinsertbase

1inch(25)ofk=

0.49, R = 2.04

Optional

Mantel

Deflector

FIREPLACE FRONT SURFACE

USA 23-1/2

CANADA 25-1/2 (648mm)

HEARTH EXTENSION

41 7/16

1052mm

12in max

MANTEL

See next page for thermal protection

calculations

WithoutMantelDeector WithMantelDeector

B. Clearances to Combustibles UnitedStatesandCanada(ULandULC)

April 9, 2014 7044-225B 9

31-I ACC

C. Calculating Alternate Floor Protection

Material

Thermal Conductivity: k value

Thekvalueindicatestheamountofheat(inBTU’s)thatwillow

in1hourthrough1squarefootofauniformmaterial1inchthick

foreachdegree(F)oftemperaturedifferencefromonesideof

the material to the other.

TheLOWER the kfactormeans less heatisbeing conducted

throughthenon-combustiblematerialtothecombustiblemate-

rialbeneathit.

Thekvalueofamaterialmustbeequalorsmallerthenthere-

quiredkvaluetobeacceptable.

(BTU)(inch)

(foot2(hour)(oF)

Thermal Resistance: R value

TheRvalueisameasureofamaterial’sresisteancetoheat

transfer.

Rvalueisconvenientwhenmorethanonematerialisused

sinceyoucanaddtheRvaluestogether,whereasyoucan

notdothisforkvalue.

TheHIGHERtheRfactormeanslessheatisbeingconduct-

edthroughthenon-combustiblematerialtothecombustible

materialbeneathit.

TheRvalueofamaterialmustbeequalorlargerthenthe

requiredRvaluetobeacceptable.

Converting k to R:

Divide1bykandmultiplytheresultstimesthethicknessininch-

es of the material.

 R=1/kxinchesofthickness

Converting R to k:

DividetheinchesofthicknessbyR.

 k=inchesofthickness/R

Calculatons:

Example:Floorprotectionrequireskvalueof0.84and3/4inch

thick.

Alternativematerialhasakvalueof0.6andis3/4inchthick.

Divide0.6by.75=kvalueof0.80.Thiskvalueissmallerthan

0.84andthereforeisacceptable.

Figure 9.2

ZERO

CLEARANCE

ONLY

Required

Thermal

Protection

Adj. Hearth

Support

1-1/2 inch (38mm) 1 inch (25mm)

1-1/2 inch (38mm)

0 to 6-1/2 inch

(0 to 165mm)

ZERO

CLEARANCE

ONLY

Required

Thermal

Protection

1 inch

(25mm)

1 inch (25mm)

Adj. Hearth

Support 1-1/2 inch (38mm)

6-1/2 inch

(165mm)

Figure 9.1

Zero Clearance Floor Thermal Protection

10 7044-225B April 9, 2014

31-I ACC

Figure 10.1

Recommended

Location

Marginal

Location

Not

Recommended

Location

Location NOT

Recommended

Multi-level Roofs

Windward

Leeward

Outside Air Kit Termination Cap

E.ChimneyTerminationRequirements

Followmanufacturer’sinstructionsforclearance,securing

ashingandterminatingthechimney.

•MusthaveanapprovedandListedcap

•Mustnotbelocatedwhereitwillbecomepluggedby

snow or other material

 • Mustterminateatleast3feet(91cm)abovetheroof

andatleast2feet(61cm)aboveanyportionofthe

roofwithin10feet(305cm).

 • Mustbelocatedawayfromtreesorotherstructures

D. Locating Your Stove & Chimney

Location of the appliance and chimney will affect perfor-

mance. As shown in Figure 10.1thechimneyshould:

 • Installthroughthewarmspaceenclosedbythebuild-

ingenvelope.Thishelpstoproducemoredraft,espe-

ciallyduringlightinganddiedownofthere.

 • Penetratethehighestpartoftheroof.Thisminimizes

theaffectsofwindturbulenceanddowndrafts.

 • Considertheappliancelocationinordertoavoidoor

and ceiling attic joists and rafters.

 • Locate termination cap away from trees, adjacent

structures,unevenrooflinesandotherobstructions.

Yourlocaldealeristheexpertinyourgeographicareaand

canusuallymakesuggestionsordiscoversolutionsthatwill

easilycorrectyourueproblem.

NOTICE:

• Chimneyperformancemayvary.

• Trees,buildings,rooflinesandwindconditionsaffect

performance.

• Chimneyheightmayneedadjustmentifsmokingor

overdraftoccurs.

NOTICE: Locating the appliance in a basement or in a

locationofconsiderableairmovementcancauseintermittent

smokespillagefromappliance.Donotlocateappliancenear

• Frequentlyopendoors

• Centralheatoutletsorreturns

Andere Handbücher für 31I-ACC

Inhaltsverzeichnis

Andere Quadra-Fire Kamin im Innenbereich Handbücher

Quadra-Fire

Quadra-Fire 21M-ACC-C Bedienungsanleitung

Quadra-Fire

Quadra-Fire VOYA-GRAND-MBK Bedienungsanleitung

Quadra-Fire

Quadra-Fire VILLAGE Series Handbuch

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Quadra-Fire

Quadra-Fire Quadra-Fire VOYAGEUR-MBK Bedienungsanleitung

Quadra-Fire

Quadra-Fire QFP44 Bedienungsanleitung

Quadra-Fire

Quadra-Fire Direct Vent Gas Fireplace Insert Bedienungsanleitung

Quadra-Fire

Quadra-Fire QFP 30 Handbuch

Quadra-Fire

Quadra-Fire MTVERNINSAE-MBK Bedienungsanleitung

Quadra-Fire

Quadra-Fire 27I-ACC Bedienungsanleitung

Quadra-Fire

Quadra-Fire QVI-25FB-S Bedienungsanleitung

Quadra-Fire

Quadra-Fire 31I-ACC Bedienungsanleitung

Quadra-Fire

Quadra-Fire QV26E-B Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100 ACC Bedienungsanleitung

Quadra-Fire

Quadra-Fire QFI30FB-IFT Montageanleitung

Quadra-Fire

Quadra-Fire CASTILE Sicherheitsleitfaden

Quadra-Fire

Quadra-Fire QV36DB-A Bedienungsanleitung

Quadra-Fire

Quadra-Fire FireBrick qvi25fb Bedienungsanleitung

Quadra-Fire

Quadra-Fire iLLAGE QV32-A Montageanleitung

Quadra-Fire

Quadra-Fire HUDSON BAY HUDBAY-FS Bedienungsanleitung

Quadra-Fire

Quadra-Fire CB1200 Bedienungsanleitung

Quadra-Fire

Quadra-Fire EXPEDITIONII-AU Bedienungsanleitung

Quadra-Fire

Quadra-Fire 43M-ACC-NZ Bedienungsanleitung

Quadra-Fire

Quadra-Fire QV32B-A Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch

Regency Fireplace Products

Regency Fireplace Products Pro Series Kurzanleitung