Quantum P1000 Series Bedienungsanleitung
Document 6221100-02, Ver. 2, Rel. 0
March 1999
1
ATL P1000 Series Library
Unpacking Instructions 0
Introduction....................................................................................................3
Selecting an Installation Location ...............................................................5
Floor Space...............................................................................................5
Floor Clearance .......................................................................................6
Floor Strength and Inclination..............................................................6
Overhead Clearance...............................................................................6
Power and Grounding ...........................................................................6
Power Inlet ........................................................................................7
Rack Current Rating Consideration ..............................................7
Grounding.........................................................................................7
Temperature......................................................................................7
Environmental Requirements...............................................................7
Unpacking the Library..................................................................................8
Unloading Space Requirements..................................................................9
Uncrating the Library .................................................................................10
Installing the Slide Assembly in the Rack................................................13
Verifying the Rack Requirements.......................................................13
Rack Current Rating Consideration ............................................13
Grounding.......................................................................................14
Temperature....................................................................................14
Determining the Mounting Position..................................................14
Installing the Slide Assembly in the Rack.........................................15
ATL P1000 Series Library Unpacking Instructions
Document 6221100-02, Ver. 2, Rel. 0
March 1999
2
Adjusting the Slide Assembly ............................................................17
Adjusting the Slide Assembly on the Mounting Brackets.......17
Adjusting the Slide Assembly Tray on the Slide Rails.............19
Removing the Library from the Pallet.....................................................22
Removing a Stand-alone Library from the Pallet............................22
Removing a Rack-mount Library from the Pallet ...........................24
Removing the Internal Packing Materials...............................................28
Opening the Doors...............................................................................28
Removing the Load and Bulk Packs..................................................28
Removing the Shipping Restraint......................................................29
Packaging the Library for Reshipment....................................................31
ATL P1000 Series Library Unpacking Instructions
Document 6221100-02, Ver. 2, Rel. 0
March 1999
Introduction 3
Introduction 0
The ATL P1000 Series is an automated tape library consisting of up to 4
tape drives and 30 DLT™ cartridges.
This document explains how to unpack the ATL P1000 Series. Once the
library is unpacked and moved to the desired installation location, set
up the library using the instructions in the ATL P1000 Series Library
User’s Guide.
The P1000 library is shipped in either a stand-alone (see figure 1) or
rack-mount configuration (see figure 2). The stand-alone P1000 is set
on casters. The rack-mount P1000 comes with a slide tray assembly for
installation in a rack.
Note: A rack is not provided with the rack-mount P1000; it must be obtained
separately.
Figure 1 ATL P1000
SeriesLibrary,Stand-alone
Configuration
Key lock
Bulk pack door
Power switch
Window
Touch screen
Load port
Load pack door
graphical user
interface (GUI)
ATL P1000 Series Library Unpacking Instructions
Document 6221100-02, Ver. 2, Rel. 0
March 1999
4 Introduction
Figure 2 ATL P1000
SeriesLibrary,Rack-mount
Configuration
Key lock
Bulk pack door
Power switch
GUI
Load port
Load pack door
Rack (not included)
ATL P1000 Series Library Unpacking Instructions
Document 6221100-02, Ver. 2, Rel. 0
March 1999
Selecting an Installation Location 5
Selecting an Installation Location 2
When selecting an installation site for the ATL P1000 Series, consider
the following requirements:
‡floor space
‡floor clearance
‡floor strength and inclination
‡power and grounding
‡environmental conditions
These requirements are also described in the ATL P1000 Series Library
User’s Guide.
Floor Space 2Figure 3 shows the floor space requirements of the stand-alone P1000.
Figure 3 Floor Space
Requirements, Stand-
alone Library
17.5 in.
(45 cm)
24 in. (61 cm) 29.5 in. (75 cm)
54 in. (137.2 cm)
Library FrontBack
ATL P1000 Series Library Unpacking Instructions
Document 6221100-02, Ver. 2, Rel. 0
March 1999
6 Selecting an Installation Location
Figure 4 shows the floor space requirements for the rack-mount P1000.
Figure 4 Floor Space
Requirements,
Rack-mount Library
Floor Clearance 4The stand-alone P1000 has a floor clearance of 0.75 in. (1.9 cm). Place
the library on a level, uncarpeted floor free of defects.
Floor Strength and
Inclination 4
The floor at the installation site must be rated at 250 lb/ft2(1221 kg/
m2). This is sufficient to support a fully loaded P1000 on the floor or in
a rack.
The floor at the installation site must be level to within 0.25 in (6.4 mm)
over a 6 ft by 6 ft (1.8 m by 1.8 m) area.
Overhead Clearance 4To remove the P1000 enclosure, there must be a minimum clearance of
24 in. (61 cm) above the library. When combined with the height of the
library (21 in./53 cm), this is a total of 45 in. (114.5 cm) from the floor
(stand-alone library) or bottom of the slide (rack-mount library).
Power and Grounding 4The library auto-ranging power supply accepts single-phase, 90 VAC
to 264 VAC input power at 47 Hz to 63 Hz.
30 in. (76.2 cm)
17.5 in.
(45 cm)
24 in. (61 cm)
19-inch rack Library
(extended
from rack)
24 in.
(61 cm)
each side
24 in.
(61 cm)
Back
Front
ATL P1000 Series Library Unpacking Instructions
Document 6221100-02, Ver. 2, Rel. 0
March 1999
Selecting an Installation Location 7
Power Inlet 4
The power inlet is an IEC-320 connector (see figure 5). For
international applications, replace the power cord with a harmonized
3x1.0mm
2power cord approved by the country where used.
Figure 5 AC Power
Receptacle
Rack Current Rating Consideration 5
Consider the current rating of the rack before installing more than one
P1000 library. The P1000 library is rated 6A/3A (120V/230V). This
means that no more than two libraries can be installed in a typical
15A/120V rack.
If other equipment is installed in the rack, determine the total current
rating of all the equipment before adding the P1000 library to the rack.
Grounding 5
The P1000 must be connected to a grounded power outlet. If the
library is rack-mounted, the rack must also be grounded.
Temperature 5
The rack temperature should be less than 90qF (32qC).
Environmental
Requirements 5
The installation site (stand-alone library) or the interior of the rack
(rack-mount library) must meet the following environmental
requirements:
‡humidity: 20% to 80%, non-condensing
‡temperature: 59qF to 90qF (15qC to 32qC)
‡altitude: sea level to 10,000 feet (3,033 meters)
NeutralLine
Ground
~100V to 120V / ~200V to 240V
6A/3A 50Hz/60Hz
IEC-320 Type
ATL P1000 Series Library Unpacking Instructions
Document 6221100-02, Ver. 2, Rel. 0
March 1999
8 Unpacking the Library
Unpacking the Library 5
The P1000 unpacking procedure consists of the following steps:
‡receiving the library from the shipper (see “Unloading Space
Requirements” on page 9)
‡uncrating the library (see “Uncrating the Library” on page 10)
‡installing the slide assembly in the rack (rack-mount library only)
(see “Installing the Slide Assembly in the Rack” on page 13)
‡removing the library from the pallet (see “Removing the Library
from the Pallet” on page 22)
‡removing the internal packing materials from the library (see
“Removing the Internal Packing Materials” on page 28)
The following sections detail each of these steps.
Note: Before performing the procedures in the following sections, make sure
the site you have chosen for the installation meets the requirements
listed in “Selecting an Installation Location” on page 5.
ATL P1000 Series Library Unpacking Instructions
Document 6221100-02, Ver. 2, Rel. 0
March 1999
Unloading Space Requirements 9
Unloading Space Requirements 5
Before uncrating the library, verify that you have sufficient space. For
the stand-alone unit, allow a minimum of six feet in front of the ramp
side of the pallet (see figure 6).
Note: Unpack the library as close to the installation site as possible.
Figure 6 Unloading Space
Requirements, Stand-
alone Library
Pallet
Pallet ramp
Library
Unloading area
(minimum)
30 in. (76 cm)
18 in. (46 cm)
33 in. (84 cm) 97 in. (2.5 m)
ATL P1000 Series Library Unpacking Instructions
Document 6221100-02, Ver. 2, Rel. 0
March 1999
10 Uncrating the Library
Uncrating the Library 6
To uncrate the P1000 library:
Procedure
1Open the top of the shipping carton by carefully cutting the
packaging tape.
The following items are stacked on top of the P1000:
‡accessories tray
‡ramp (stand-alone library) or slide assembly (rack-mount
library)
2Remove these items from the carton and set them aside.
3Remove all foam supports from inside the carton (see figure 7 on
page 11 and figure 8 on page 12).
Andere Handbücher für P1000 Series
1
Inhaltsverzeichnis
Andere Quantum Lagerung Handbücher
Quantum
Quantum StorNext QM1200 Bedienungsanleitung
Quantum
Quantum DXi4520 Bedienerhandbuch
Quantum
Quantum Tape Drive SDLT 600A Bedienungsanleitung
Quantum
Quantum Quantum Bigfoot CY Bedienungsanleitung
Quantum
Quantum Scalar 50 Leitfaden
Quantum
Quantum StorNext QS1200 Technisches Handbuch
Quantum
Quantum DXi6701 Technisches Handbuch
Quantum
Quantum Scalar i6 Bedienungsanleitung
Quantum
Quantum DLTtape SDLT 600 Bedienungsanleitung
Quantum
Quantum ACL 4/52 Handbuch
Quantum
Quantum LTO-4 (Model B) Bedienungsanleitung
Quantum
Quantum Scalar 50 Bedienungsanleitung
Quantum
Quantum PX500 Series Bedienungsanleitung
Quantum
Quantum ValueLoader DLT VS80 Betriebsanleitung
Quantum
Quantum Scalar i2000 Bedienungsanleitung
Quantum
Quantum ATL StackLink Bedienungsanleitung
Quantum
Quantum LTO 3A Bedienungsanleitung
Quantum
Quantum DXi4701 Bedienungsanleitung
Quantum
Quantum P3000 Series Bedienungsanleitung
Quantum
Quantum Atlas 10K II Bedienungsanleitung
Beliebte Lagerung Handbücher anderer Marken
Spectra Logic
Spectra Logic T-Series Spectra T50e Bedienungsanleitung
Panasonic
Panasonic LKM-F931-1 Bedienungsanleitung
Tabernus
Tabernus Enterprise Erase E2400 Bedienungsanleitung
Rocstor
Rocstor COMMANDER 3F series Bedienungsanleitung
HP
HP P9000 Bedienungsanleitung
Western Digital
Western Digital Ultrastar Data60 Bedienungsanleitung