Radio Shack ET-926 Bedienungsanleitung

Cat. No. 43-1096

OWNER’S MANUAL

Please read before using this equipment.

ET-926

900-MHz Digital Spread Spectrum

Cordless Phone

43-1096.fm Page 1 Tuesday, August 17, 1999 3:47 PM

FEATURES

RadioShack is a registered trademark used by Tandy Corporation.

Your RadioShack ET-926 900-MHz

Digital Spread Spectrum Cordless

Phone uses the most advanced cord-

less telephone technology to give you

superior audio quality and extended

range.

Its features include:

Spread Spectrum Technolo

—

spreads signals out over several fre-

quencies rather than locking onto just

one.

900-MHz Operation — provides less

interference, clearer sound, and longer

range than many other cordless

phones (over twice the range of 46/49-

MHz cordless phones).

20 Channels — automatically selects

a clear channel when you make or an-

swer a call.

Securit

Access-Protection Code —

automatically prevents other cordless

phone users from using your phone

line while the handset is off the base.

Redial — lets you quickly redial the

last number dialed.

20-Number Memor

Dialin

— lets

you store up to 20 numbers in memory

for easy dialing.

e— lets you send a paging signal

from the base to the handset to page

someone or locate the handset if you

misplace it.

Flash — sends an electronic switch-

hook signal for use with special phone

services, such as Call Waiting.

Volume Control — lets you adjust the

volume you hear through the handset.

Pro

rammable Rin

er — lets you se-

lect from eight tone/volume settings.

Tone/Pulse Dialin

— you can use

this phone with either type of service.

Quick Talk — lets you answer a call

by just lifting the handset from the

base.

Answer — lets you press

any key to answer a call when the

handset is away from the base.

Hearin

-Aid Compatibilit

— lets

you use your phone with hearing aids

that have a T (telephone) switch.

This telephone has been tested and

found to comply with all applicable UL

and FCC standards.

43-1096.fm Page 2 Tuesday, August 17, 1999 3:47 PM

Important Note: Cordless phones

such as this one require AC power to

operate. When the AC power is off,

you cannot dial out or receive incoming

calls using your ET-926. To be safe,

you should also have a phone that

does not need AC power to operate

(not a cordless phone) so you can still

make and receive calls if there is an

AC power failure.

We recommend you record your

phone’s serial number here. The num-

ber is on the bottom of the base.

Serial Number __________________

This symbol is intended to alert you

to the presence of uninsulated dan-

gerous voltage within the product’s

enclosure that might be of sufficient

magnitude to constitute a risk of

electric shock. Do not open the

product’s case.

This symbol is intended to inform

you that important operating and

maintenance instructions are in-

cluded in the literature accompany-

ing this product.

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER OR BACK. NO USER-SERVICE-

ABLE PARTS INSIDE. REFER SERVIC-

ING TO QUALIFIED PERSONNEL.

Warning: To reduce the risk of fire

or shock hazard, do not expose

this product to rain or moisture.

CAUTION !

READ THIS BEFORE

INSTALLATION

Each device that you connect to the

phone line draws power from the

phone line. We refer to this power draw

as the device’s

ringer equivalence

number

, or REN. The REN is on the

bottom of the base.

If you are using more than one phone

or other device on the line, add up all

the RENs. If the total is more than five,

your phones might not ring. In rural ar-

eas, a total REN of three might impair

ringer operation. If ringer operation is

impaired, remove a device from the

line.

FCC STATEMENT

This telephone complies with Part 68

FCC Rules

. You must, upon re-

quest, provide the FCC Registration

Number and the REN to your phone

company. These numbers are on the

bottom of the base.

Note: You must not connect your

phone to any of the following:

• coin-operated systems

• party-line systems

• most electronic key phone sys-

tems

43-1096.fm Page 3 Tuesday, August 17, 1999 3:47 PM

CONTENTS

Installation ............................................................................................................ 5

Selecting a Location ........................................................................................ 5

Placing the Base on a Desk Top ............................................................... 5

Mounting the Base on a Wall Plate ........................................................... 6

Mounting the Base Directly on the Wall .................................................... 8

Connecting and Charging the Battery Pack .................................................. 10

Setting the Dialing Mode ............................................................................... 11

Setting the Ringer Tone/Volume .................................................................... 12

Using the Belt Clip ......................................................................................... 12

Operation ............................................................................................................ 13

Making and Receiving Calls .......................................................................... 13

Setting the Handset Volume .......................................................................... 13

Using Redial .................................................................................................. 13

Using Flash .................................................................................................... 14

Using Tone Services on a Pulse Line ............................................................ 14

Paging ........................................................................................................... 14

Memory Dialing .............................................................................................. 15

Storing a Number in Memory .................................................................. 15

Entering a Pause .................................................................................... 16

Dialing a Memory Number ...................................................................... 16

Chain-Dialing Service Numbers .............................................................. 16

Testing Stored Emergency Numbers ...................................................... 17

Troubleshootin

................................................................................................. 18

Care and Maintenance ....................................................................................... 20

Replacing the Battery Pack ........................................................................... 21

The FCC Wants You to Know ........................................................................ 22

Lightning ........................................................................................................ 22

43-1096.fm Page 4 Tuesday, August 17, 1999 3:47 PM

INSTALLATION

SELECTING A

LOCATION

You can place the ET-926’s base on a

desk top or table, or mount it on a wall.

Select a location that is:

• near an AC outlet

• near a telephone line jack

• out of the way of normal activities

• away from electrical machinery,

electrical appliances, metal walls

or filing cabinets, wireless inter-

coms, alarms, and room monitors

• away from other cordless phones

The base’s location affects the hand-

set’s range. If you have a choice of

several locations, try each to see

which provides the best performance.

Caution: The supplied RadioShack

AC adapter was designed specifically

for your ET-926. Use only the supplied

adapter.

Notes:

• Your telephone connects directly

to a modular telephone line jack. If

your phone line jack is not a mod-

ular jack, you can update the wir-

ing yourself, using jacks and

adapters available at your local

RadioShack store. Or, you can let

the phone company update the

wiring for you.

• The USOC number of the jack to

be installed is RJ11C (RJ11W if

you want to mount it on a wall

plate).

Placing the Base on a

Desk Top

Follow these steps when you place the

base on a desk, shelf, or table.

1. Plug one end of the supplied long

modular cord into the TEL LINE

jack on the back of the base.

2. Plug the modular cord’s other end

into a modular phone line jack.

43-1096.fm Page 5 Tuesday, August 17, 1999 3:47 PM

3. Insert the supplied AC adapter’s

barrel plug into the DC IN 9V jack

on the back of the base.

4. Route the adapter’s cord through

the strain relief slot on the base.

5. Plug the adapter into a standard

AC outlet.

6. Lift the base’s antenna to a verti-

cal position.

Strain Relief

Slot

Mounting the Base on a

Wall Plate

1. Insert the two catches at the top of

the bracket into the upper slots on

the bottom of the base. Then

press the two latches on the sides

of the bracket into the lower slots.

2. Plug one end of the supplied short

modular cord into the TEL LINE

jack on the back of the base.

43-1096.fm Page 6 Tuesday, August 17, 1999 3:47 PM

3. Route the modular cord through

the wide right groove on the bot-

tom of the bracket.

4. Insert the supplied AC adapter’s

barrel plug into the DC IN 9V jack

on the back of the base.

AC ADAPTOR

DC IN 9V

PULSE-TONE TEL LINE

5. Route the adapter’s cord through

the narrow groove on the bottom

of the bracket.

6. Plug the short modular cord into

the wall plate jack, press the

excess cord into the slot in the

center of the bracket, then align

the bracket’s keyhole slots with

the wall plate studs and slide the

base downward to secure it.

7. Plug the adapter into a standard

AC outlet.

8. Lift the base’s antenna to a verti-

cal position.

AC ADAPTOR

DC IN 9V

PULSE-TONE

TEL LINE

AC ADAPTOR

DC IN 9V

PULSE-TONE

TEL LINE

43-1096.fm Page 7 Tuesday, August 17, 1999 3:47 PM

Mounting the Base Directly

on the Wall

For this mounting method, you need

two flat-head wood screws (not sup-

plied) with heads that fit into the key-

hole slots on the bottom of the base.

1. Drill two holes 35/16

inches apart. Then

thread a screw into

each hole, letting the

heads extend about

3/16 inch from the

wall.

2. Insert the two catches at the top of

the bracket into the upper slots on

the bottom of the base. Then

press the two latches on the sides

of the bracket into the lower slots.

3/16

35/16

3. Plug one end of the supplied long

modular cord into the TEL LINE

jack on the back of the base.

4. Route the modular cord through

the wide right groove on the bot-

tom of the bracket.

AC ADAPTOR

DC IN 9V

PULSE-TONE

TEL LINE

43-1096.fm Page 8 Tuesday, August 17, 1999 3:47 PM

5. Insert the supplied AC adapter’s

barrel plug into the DC IN 9V jack

on the back of the base.

6. Route the adapter’s cord through

the narrow groove on the bottom

of the bracket.

AC ADAPTOR

DC IN 9V

PULSE-TONE

TEL LINE

7. Align the keyhole slots with the

mounting screws and slide the

base downward to secure it.

8. Plug the modular cord into a mod-

ular phone line jack.

9. Plug the adapter into a standard

AC outlet.

10. Lift the base’s antenna to a verti-

cal position.

AC ADAPTOR

DC IN 9V

PULSE-TONE

TEL LINE

43-1096.fm Page 9 Tuesday, August 17, 1999 3:47 PM

CONNECTING AND

CHARGING THE

BATTERY PACK

The ET-926 comes with a recharge-

able nickel-cadmium battery pack in

the handset. Before using your phone,

you must connect the battery pack,

then charge it for about 14 hours.

1. Slide the cover in the direction of

the arrow to remove it.

2. Unfasten the plastic retainer strap

and lift the battery pack out of the

compartment. Plug the battery

pack’s connector into the socket in

the compartment. The connector

fits only one way.

3. Replace the battery pack inside

the compartment and refasten the

retainer strap.

4. Replace the cover.

To charge the battery pack, place the

handset upright on the base if you

placed the ET-926 on a desk top, or

hang the handset on the holder if you

mounted it on a wall. The In Use/

Charge indicator on the base lights.

When the handset beeps and the Talk/

Batt Low indicator on the handset

flashes, recharge the battery pack.

Notes:

• If the In Use/Charge indicator

does not light when you place the

handset on the base, be sure the

battery pack and AC adapter are

correctly and securely connected.

Also, check the charging contacts

on the handset and the base. If

the contacts are dirty or tarnished,

clean them with a pencil eraser.

43-1096.fm Page 10 Tuesday, August 17, 1999 3:47 PM

Inhaltsverzeichnis

Andere Radio Shack Schnurloses Telefon Handbücher

Radio Shack

Radio Shack ET-1105 Bedienungsanleitung

Radio Shack

Radio Shack 43-3704 Bedienungsanleitung

Radio Shack

Radio Shack ET-905 Bedienungsanleitung

Radio Shack

Radio Shack 43-3871 Bedienungsanleitung

Radio Shack

Radio Shack TAD-729 Bedienungsanleitung

Radio Shack

Radio Shack ET-2101 Bedienungsanleitung

Radio Shack

Radio Shack Presidian Bedienungsanleitung

Radio Shack

Radio Shack 43-3856 Bedienungsanleitung

Radio Shack

Radio Shack 2.4 GHz Digital Spread Spectrum Cordless Telephone with Caller ID/Call Waiting... Bedienungsanleitung

Radio Shack

Radio Shack 43-3577 Bedienungsanleitung

Radio Shack

Radio Shack ET-1109 Bedienungsanleitung

Radio Shack

Radio Shack TAD 1130 Bedienungsanleitung

Radio Shack

Radio Shack ET-548 Bedienungsanleitung

Radio Shack

Radio Shack ET-3504 Bedienungsanleitung

Radio Shack

Radio Shack 43-3827 Bedienungsanleitung

Radio Shack

Radio Shack ET-551 Bedienungsanleitung

Radio Shack

Radio Shack 43-3815/43-3898 Bedienungsanleitung

Radio Shack

Radio Shack 43-3558 Bedienungsanleitung

Radio Shack

Radio Shack 43-3815 Bedienungsanleitung

Radio Shack

Radio Shack 900MHz Hands-free Phone Bedienungsanleitung

Radio Shack

Radio Shack 43-324 Bedienungsanleitung

Radio Shack

Radio Shack 43-3576 Bedienungsanleitung

Radio Shack

Radio Shack ET-917 Bedienungsanleitung

Radio Shack

Radio Shack 43-143 Bedienungsanleitung

Beliebte Schnurloses Telefon Handbücher anderer Marken

3Com

3Com NBX Bedienungsanleitung

Panasonic

Panasonic KX-TGK210HK Bedienungsanleitung

Panasonic

Panasonic KX-TCA181EX Bedienungsanleitung

BT FREESTYLE 3200 Bedienungsanleitung

AT&T

AT&T CL84102 Bedienungsanleitung

BREZZICNI

BREZZICNI CL-3622 Bedienungsanleitung

Panasonic

Panasonic KX-TG1831NZ Bedienungsanleitung

Panasonic

Panasonic KX-TG7301E Bedienungsanleitung

Sanyo

Sanyo CLT-J70 Bedienungsanleitung

Amplicomms

Amplicomms BigTel 201 Bedienungsanleitung

GE 26992 Bedienungsanleitung

AT&T

AT&T E1812B Bedienungsanleitung

Sanyo

Sanyo CLT-670 Bedienungsanleitung

GE 15432970 Bedienungsanleitung

Curtis

Curtis TC595 Bedienungsanleitung

Gigaset

Gigaset Gigaset 3000 Micro Bedienungsanleitung

Poly

Poly VVX D230 Einrichtungshandbuch

AT&T

AT&T 7625 Bedienungsanleitung